Advertisement
Quick Links
Important Safety Advice Sheet
PLEASE READ BEFORE YOU BEGIN:
• Please read and understand the instructions prior to assembly.
Incorrect installation of this product could possibly result in personal
injury or physical damage.
• WallBeds Australia recommends two people to safely assemble and
install the wall bed - It is not recommended you try to install this bed
on your own.
• The wall bed MUST be securely fastened to the wall. Failure to do
so will cause the bed to tip over & may cause damage to the cabinet
or serious personal injury.
• All additional cabintery must be securely fasten to the Wall Bed
cabinet.
• Whilst these products are DIY it is recommended the wall bed be
installed by a qualified trades person if you are not comfortable with
the installation of this product.
WallBeds Australia is not responsible for any damages or
injuries incurred by incorrect installation of this product.
1
Advertisement
Related Manuals for Wallbeds Australia AB3a
Summary of Contents for Wallbeds Australia AB3a
- Page 1 Incorrect installation of this product could possibly result in personal injury or physical damage. • WallBeds Australia recommends two people to safely assemble and install the wall bed - It is not recommended you try to install this bed on your own.
- Page 2 AB3a Cupboard Drawer and Bookcase Assembly Instructions Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior to assembly, separate and group all matching panels numbers. Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the units have been built, as these will assist with assembly.
- Page 3 AB3a Cupboard and Drawer Hardware Parts Small Handle Drawer Runners & Drawer Clip Metal Drawer Sides Handle Fixing Screw Door Hinge Door Hinge Clip Euro Screw Cam Lock Cam Pin Done Head Screw 28mm Wood Screw Step 1 – Inserting Cupboard and Drawer Cabinetry Hardware Cam Locks –...
- Page 4 Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located on the cabinet sticker. Bottom Panel Top Panel End Panel Drw Bot End Panel NOTE: In the NOTE: In the Top Bottom Panel Insert Panel Insert the cam the cam pins on the pins on the same...
- Page 5 Step 2 – Cupboard & Drawer Cabinet Assembly Start the cabinet assembly by using either one of the cabinet End Panels. Cabinet Back Panel - Ensuring the cam locks are facing away from the inside. Place the cabinet back panel onto the side panel. Match up the cam locks with the cam pins. Tighten the cam locks and cam pins together by using a Philips head hand screwdriver.
- Page 6 AB3a Bookcase Assembly Instructions Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior to assembly, separate and group all matching panels panel numbers. Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the units have been built, as these will assist with assembly.
- Page 7 AB3a Cabinet Hardware Parts Cam Lock Small Handle Cam Pin Shelf Pin Handle Fixing Screw Door Hinge Clip Door Hinge 28mm Wood Screw Step 1 – Inserting Cabinetry Hardware Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part located on the cabinet sticker.
-
Page 8: Step 2 - Cabinet Assembly
Door Hinge Clips – Attach the Hinge Plates before assembling the cabinetry. With the arrow indicator on the hinge block facing to the front edge of the panel. Line up the Hinge Plate with the pre-drilled holes in the End Panel. Fix these by tapping them in gently with a hammer, then tightening the screws. - Page 9 Step 5 – Fitting the Door Hinges and Door Panel Attaching the Door to the Cabinet - Clip the hinge arm into the hinge block previously attached to the bookcase. Attaching the Cabinet to your wall bed - Check that the cabinet door panel is flush with the front edge of the wall bed End Panel.
- Page 10 Image 2 Image 1 Image 3 Image 4...
- Page 11 Image 5 Image 6 Image 8 Image 7 Image 9 Image 10...
- Page 12 Image 12 Image 11 Image 14 Image 13 NOTE: Image s 13 & 14 are a representation of how to place Top unit onto Lower unit. These images may not represent each individual product.