Related Manuals for Uni-ram UG2000DM Series
Summary of Contents for Uni-ram UG2000DM Series
- Page 1 USER MANUAL UG2000DM SERIES AUTOMATIC SPRAY GUN CLEANERS Uni-ram Corporation www.uniram.com 381 Bentley St. 905-477-5911 Markham On L3R 1P7 sales@uniram.com REV 2018-12...
-
Page 2: Common Features
Inspect the shipping carton for any sign of transport damage. Carefully remove the unit from the ship- ping carton and check the unit for damage. Report any transport damage immediately to the carrier and to Uni-ram Corporation. Initiate a freight claim with the carrier. The manufacturer is not respon- sible for the freight damage. - Page 3 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 UG2000DM FIGURE 1 Cleaning Tank (inside) Timer Drain Valve (inside) Drain Hose Suction hose for Wash pail and suction hose for brush Wash Pail Foot petal for brush...
-
Page 4: Air Supply
MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 LOCATION Position the unit in a well-ventilated area away from sparks, heat and open flames, at least 6 " from the back wall. AIR SUPPLY • Connect a male air supply adapter (not supplied) into the female Air Inlet on the unit. The male air supply adapter is 1/4"... - Page 5 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 PRE - CLEAN • Disconnect the spray gun from the air hose. • Remove disposable cup shown in A. • Squirt solvent into disposable cup adapter, shown in B photo. • Pull the gun’s trigger to fl ush the solvent through the fl uid channel.
- Page 6 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 SPRAY GUN INSTALLED IN TANK brush Caps points to the corner jets Location for Push On Nozzle Extension INSTALLING SPRAY GUNS IN TANK Place the spray gun on the nozzle with the cap facing the corner.
- Page 7 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12...
- Page 8 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 Prevent Solvent From Entering the Air Passage of Spray Gun: insert the plastic plug into the air fi tting as in the photo below . Positive air will fl ow through the passage way to the cap during cleaning.
- Page 9 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 MAINTENANCE • A removable screen fi lter is installed at the end of the suction pipe, in the wash pail. See the photos below. • Once each week, remove the wash pail from the cabinet, remove the suction pipe with the pail, see photos below, unscrew the metal fi lter ( see right photo below) and clean the fi lter in a cup of solvent.
-
Page 10: Troubleshooting
MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 TROUBLE SHOOTING PROBLEM REASON CORRECTIVE ACTION WASH PUMP MAKES PUMPING SOUND BUT Open drain valve (put in vertical position), if Drain valve closed SOLVENT DOES NOT FLOW not already open FROM THE JETS Check wash liquid level. - Page 11 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 Trouble shooting continued SYMPTOM REASON CORRECTIVE ACTION Replace solvent / water and AQUA- INSIDE WALL OF TANK IS KLEEN in pail. Consider a solvent COATED WITH PAINT EVEN that is formulated for type of paint...
- Page 12 This procedure may have to be repeated several times. If this procedure does not work, the pump must be replaced. If you need to replace the pump call the Uni-ram Service Engineer. The warranty on the diaphragm pump is two years from date of purchase.
- Page 13 MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 UG4000E FLOW DIAGRAM Use the diagram to trace the fl ow of compressed air and solvent.
-
Page 14: Replacement Parts
MANUAL - UG2000DM SERIES SPRAY GUN CLEANERS REVISED 2018-12 REPLACEMENT PARTS art No. Description 110-430 Nozzle Adapter, Push On, Conventional Systems Only 110-430PPS Nozzle Adapter, Push On, Disposable and Conventional Systems 780-3530 Nozzle Adapter, Disposable Cup Systems Only 100-413F Paint Cap Holder... - Page 15 "Conditions of Warranty" as consumables are not covered. Uni-ram reserves the right to direct the customer to ship the unit collect to the Uni-ram factory or to an approved Service Center for repair using the Uni-ram Return Goods Procedure or to repair the unit on- site.