Advertisement
Available languages
Available languages
Quick Links
Page 1 of 8
ECC0310R
FITTING INSTRUCTIONS FOR ECC0310R
LHS ALTERNATOR COVER
HONDA CBR1000RR-R & SP 2020-
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Advertisement
Related Manuals for R&G ECC0310R
Summary of Contents for R&G ECC0310R
- Page 1 Page 1 of 8 ECC0310R FITTING INSTRUCTIONS FOR ECC0310R LHS ALTERNATOR COVER HONDA CBR1000RR-R & SP 2020- HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
-
Page 2: Tools Required
0 BOLT = 40Nm M12 BOLT = 40Nm LEGEND ITEM NO. DESCRIPTION ITEM 1 ECC0310R ENGINE CASE COVER ITEM 2 M6 x 1.00 x 45mm BUTTON HEAD BOLT ITEM 3 M6 x 1.00 x 45mm CAP HEAD BOLT FITTING PICTURES... - Page 3 Page 3 of 8 ECC0310R Picture 3 Picture 4 Picture 5 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 4: Fitting Instructions
Page 4 of 8 ECC0310R Picture 6 FITTING INSTRUCTIONS • Please make sure the engine is cold before proceeding with the fitting of the R&G cover. • To begin, the belly pan must be removed, to do this both left and right-handed lower side panels can be removed as one unit. - Page 5 Page 5 of 8 ECC0310R • Offer up the R&G cover to the engine and carefully fit it over the casing. Ensure that the three R&G bolt holes are lined up with the holes in the engine casing, and then push the case on as far as it will •...
- Page 6 Page 6 of 8 ECC0310R NOTICE DE MONTAGE POUR ECC0310R PROTECTION CARTER MOTEUR CÔTÉ GAUCHE HONDA CBR1000RR-R & SP 2020- E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS...
-
Page 7: Outils Requis
0 BOULON = 40Nm M12 BOULON = 40Nm LÉGENDE ARTICLE NO. DESCRIPTION QTÉ ARTICLE 1 ECC0310R PROTECTION CARTER MOTEUR ARTICLE 2 M6 x 1.00 x 45mm BOULON ARTICLE 3 M6 x 1.00 x 45mm BOULON NOTICE DE MONTAGE • Veuillez vous assurer que le moteur soit froid avant de procéder au montage de la protection R&G. - Page 8 Page 8 of 8 ECC0310R • À l'aide de clés hexagonales, serrez les boulons de manière égale pour qu'ils mettent la protection en place. NE SERREZ PAS COMPLÈTEMENT. • Enfin, utilisez une clé dynamométrique réglée à 10 N / m (7 Lb / ft) pour serrer complètement.