Lid, Measuring Cup; Cleaning & Storage; Operating Notes - Wilfa POWER FUEL PB-1200S Operating Instructions Manual

10 10

Lid, Measuring Cup

„ Insert the measuring cup in the lid by aligning the two tabs in the slots
on the lid and twisting to lock. Then push the lid onto the blender jug to
close it. To open the lid, pull the lap up.
Cleaning & Storage
„ Unplug the appliance from the wall socket.
„ Do not immerse the base unit or power cord in water or other liquids.
„ Clean surface of the blender jug with a soft cloth or sponge.
The measuring cup can be disassembled for cleaning.
„ The blender jug can be rinsed with water. It can also be cleaned by
pouring 2 cups of water into the blender jug, closing the lid and then
operating the blender in Pulse Mode. Then pour out the water and dry
with soft cloth.
„ After cleaning, place the blender jug on its side or upside down (Note 1)
to dry. Do not immerse the whole jug in water.
„ Clean the base unit with a soft cloth. NEVER immerse it in water or other
liquid.
Note: Tamper and blender jug shall not be washed in a dishwasher.
Note 1: If you place the blender jug in upside down position, please remove residual
water with a dry cloth. Do not leave it close to the sink or basin in order to avoid water
spraying onto the bottom part of the jug. This may cause the bearing to rust, thus
affecting the performance of the blender

Operating notes

„ The blender cannot be operated if:
– The jug is not irmly positioned on the base.
– The speed dial is turned to variable speed before the jug is positioned
irmly on the base.
– The jug is removed during operation and put back again.
„ You need to turn the speed dial back to the "OFF" (OFF) position and
make sure the jug is positioned irmly on the base. This will reset the
blender.
„ If the motor is forced to slow down because of food that is too big in
size or if there is not enough liquid in the jug, and if it operates for a
long period, the temperature monitoring system will trigger and stop
the operation of the motor. The red LED will blink at a rate of 2 Hz. In this
case, unplug the blender and leave it in a place with good ventilation to
cool down the motor temperature for 45 minutes. The system will reset
and the blender can be used again.
„ During operation, close the lid tightly to avoid scalding due to spraying
of hot liquids.
„ Keep hands and utensils out of the container while the motor is running
to prevent the possibility of severe injury and/or damage.
„ When making hot beverages such as soybean milk, or making hot soup,
please check that the lid is secured tightly to the jug to prevent it from
falling off. It is advisable to start operation at a low speed setting and
then increase the speed gradually, or use the PULSE mode.
„ When making sauces (e.g. almond sauce, jam and sesame sauce) or
stufings or processing nuts, put in between 2 and 3 cups of ingredients.
The amount should neither be too large or too small. Keep the blending
time below 2 minutes to prevent any burnt smell due to overheating. Too
large a quantity of ingredients may lead to overloading and overheating
of the motor. In this case, wait until the motor temperature falls before
operating again.
„ Add liquids and soft foods before putting in hard food or ice cubes.
„ When the operation inishes, wait until the blade assembly comes to
a complete stop before removing the blender jug. Otherwise, the drive
gear may be damaged.
„ If you notice a scorched smell from the blender, stop the operation
immediately. It may be caused by abrasion of the rubber cushion base
if this is not properly assembled.
„ When blending thick and sticky food at high speed, please start the
operation at low speed. If there is still no rotation, disconnect the power
and stir the contents of the blender jug using a rubber stirrer to drive
out air trapped in the food. Then close the lid and switch on to resume
operation.
„ Do not operate for more than 10 minutes at a time.
11 11