Operation - Tarrington House QA18-0000001813 Assembly Instructions Manual

Connecting / exchanging gas cylinders
WARNING!
Only use the provided or equivalent pressure regulator(s) (→ TECHNICAL DATA) in order to guarantee that it functions safely and efficiently. Using
an improper or a defective pressure regulator is dangerous. Consult your specialised dealer concerning suitable pressure regulators. The type of
the pressure regulator to be used must indicate that it complies with the relevant standard and requirement (EN 16129).
Consult your local gas retailer regarding suitable gas cylinders and pressure regulators (→ TECHNICAL DATA).
NOTE: Gas connections are equipped with left handed threads; the screw-nut needs to be turned counter clockwise!
1. Ensure that there are no ignition sources like cigarettes, open flames, sparks and other heat sources nearby when connecting or replacing gas cylinders.
GB
2. Place the gas cylinder on level ground next to the appliance.
3. Make sure that all control knobs on the appliance are in the off positions OFF.
4. Make sure that the gas valve of the gas cylinder(s) and / or the gas regulator(s) is / are closed.
5. Connect the gas hose(s) to the gas line(s) of the appliance (Fig. 1). Do not overtighten the connections. Use only the delivered hardware to secure the
connections. Do not use sealing tape or a liquid sealant.
6. Connect the / each pressure regulator to the gas cylinder inlet(s) by turning the pressure regulator counter clockwise (Fig. 2). Secure the connection(s) with
the retention nut(s).
7. Connect the other end of the gas hose(s) to the pressure regulator(s) (Fig. 3).
8. Check all connections for gas leaks (→ Testing for gas leaks).
1
Testing for gas leaks
WARNING! Risk of explosion!
Never check for gas leaks using a match or any other open flame!
Test all connections, fittings and all gas hoses for gas leaks every time prior use of the appliance, or each time the gas cylinder(s) is / are changed. Make sure
this procedure is carried out in a well ventilated area away from flames, sparks or any heat sources. Do not attempt to light the appliance, if you smell gas.
1. Make sure that all control knobs on the appliance are in the off positions OFF.
2. Open the gas valve of the gas cylinder(s) and / or the pressure regulator(s).
3. Apply leak detector spray or half water / half soap solution with a brush to all the connection points.
4. Turn the gas supply on the valve of the gas cylinder(s) and or the pressure regulator(s) off immediately, if you spot gas bubbles forming on the interested
areas. Tighten all connections again and repeat the test.
5. Do not use the appliance but contact your retailer, if gas bubbles keep forming.
Burning-off
Before first use, remove any production residue and clean the appliance:
1. Operate the appliance at high temperature with the cover opened for about 10 - 15 minutes to burn-off production residues (→ IGNITING THE
BURNER(S)).
2. Turn the appliance off; allow it to cool and clean all parts (→ CLEANING AND CARE) afterwards.

OPERATION

WARNING! Danger of burns!
This appliance generates heat and escaping steam during use! Take proper precautions to prevent risk of burns, fires, or other damages to people
and property! Wear protective oven mittens or gloves. Use proper tools like barbecue tong and prongs to turn over grillables!
COOKING TIPS
1. Brush the grill grates with cooking or vegetable oil, before using the appliance. Use a brush with a long handle. The juices from the food drip onto the
heater during cooking and vaporise. The steam arising from this process contributes to the taste of the food.
2. Set the control knob(s) to the desired temperature in order to reach your desired cooking results. The build in thermometer could be used as reference (not
calibrated).
3. Keep the cover(s) closed in order to achieve a more consistent result and to cook larger pieces of meat or whole chickens.
4. Avoid opening the cover(s) too often as accumulated heat escapes each time and the grilling time increases as a result.
IGNITING THE BURNER(S)
The burner(s) can be ignited with the built-in electronic ignitor(s) or alternatively manually with a match.
1. Wait 5 minutes after all connections are made and make sure no gas is leaking (→ Testing for gas leaks).
2. Open the cover(s) of the appliance. Refer to the illustration pages in the front section of this instruction manual for details. Turn all control knobs to the off
positions OFF (Fig. 1).
3. Open the valve of the gas cylinder(s) and / or the pressure regulator(s) (Fig. 2).
4. Keep your face and body as far away from the appliance as possible while igniting.
2
1.
8
3
2.
2.
1.