Operation - Tarrington House K103M1BME3-1 Assembly Instructions Manual

Test all connections, fittings and all gas hoses for gas leaks every time prior use of the appliance, and each time the gas cylinder is / are changed. Make sure
this procedure is carried out in a well ventilated area away from flames, sparks or any heat sources. Do not attempt to light the appliance if you smell gas. For
the initial leak test, make sure the LPG cylinder is 80% full.
1. Make sure that all control knobs on the appliance are in the off positions OFF.
2. Open the gas valve of the gas cylinder or the pressure regulator.
3. Apply leak detector spray or half water / half soap solution with a brush to all the connection points.
4. Turn the gas supply on the valve of the gas cylinder or the pressure regulator off immediately, if you spot gas bubbles forming on the checked areas.
Tighten all connections again and repeat the test.
5. Turn off the gas supply and do not use the appliance but contact your retailer, if gas bubbles keep forming.
Burning-off
Before first use, remove any production residue and clean the appliance:
GB
1. Operate the appliance at high temperature with the cover opened for about 10 - 15 minutes to burn off production residues (
/ SIDE BURNER(S)).
2. Turn the appliance off; allow it to cool down before cleaning all the parts (

OPERATION

WARNING! Danger of burns!
This appliance generates heat and escaping steam during use! Take proper precautions to prevent risk of burns, fires, or other damages to
people and property! Wear protective oven mittens or gloves. Use proper tools like barbecue tong and prongs to turn over grillables!
WARNING!
The black area of the handle (see below picture for reference) will become hot when the appliance In use, BE CAREFUL! Do not touch the black
area.
COOKING TIPS
1. Brush the grill grates with cooking or vegetable oil prior to using the appliance. Use a brush with a long handle. Juices from the food drip onto the heater
during cooking and vaporise. The steam arising from this process contributes to the taste of the food.
2. Adjust the control knobs between HI and LO position in order to achieve your desired cooking results. The built-in thermometer on the cover can be used
for reference (not calibrated).
3. Keep the cover closed in order to achieve a more consistent result and to cook larger pieces of meat or whole chickens.
4. Avoid opening the cover too often as accumulated heat escapes each time, increasing the grilling duration as a result.
ENERGY SAVING TIPS
• Reduce the opening time of the lid.
• Turn the appliance off as soon as cooking is completed.
• Preheat the appliance for 10 to 15 minutes only (except for the first use).
• Do not preheat longer then recommended.
• Do not use a higher setting than required.
Only place the gas cylinder in the appliance's gas cyliner compartment, not at the side of the appliance. The hose dimension is 8 mm diameter.
IGNITING THE BURNER(S) / SIDE BURNER(S)
WARNING!
Before attempting to light your appliance you must refer to the lighting instructions and warning / safety points.
The burners can be ignited with the spark ignition which combine with the gas taps.
1. Wait 5 minutes after all connections are made and make sure no gas is leaking (
2. Open the cover of the appliance. Turn all control knobs to the off positions OFF.
3. Open the valve of the gas cylinder and / or the pressure regulator.
4. Keep your face and body as far away from the appliance as possible while igniting.
WARNING! Risk of explosion!
Always ignite the burner(s) within 5 seconds after turning the control knob to a position between HI and LO. Otherwise, gas can collect inside
the appliance causing an explosion on ignition.
WARNING!
Turn all the control knobs to the off positions OFF, if any burner does not ignite within 5 seconds. Wait for 5 minutes to let the gas dissipate and
try again.
WARNING!
If any burner still does not ignite after a few tries, it could indicate a problem with the gas supply. Turn the gas supply off on the appliance as well
as on the gas cylinder and / or the pressure regulator. Do not use the appliance until the cause of the problem has been found
( TROUBLESHOOTING).
5. Push the control knob of the selected burner in (A) and hold in this position for 3-5 seconds to allow gas flow and then turn anticlockwise to HI position
(B). It can spark to the burner lighting tube (C). You will hear a "snap" from the igniter and you will also see a 7 - 13 cm orange flame coming from the
burner lighting tube at the left side of the burner (D). Continue to hold the burner control knob in for two seconds after the "snap", this will allow gas to flow
completely down the burner tube (E) and insure ignition.
6. To adjust the heat, set the control knob between HI and LO position. At HI setting the burner flame should be approximately 12-20 mm long with a
minimum of orange flame. Turn the control knob fully anticlockwise for minimum setting.
CLEANING AND CARE).
Testing for gas leaks).
- 10 -
IGNITING THE BURNER(S)