Advertisement
Quick Links
Item No.: SPE-G110
Accessory List
Attention: The drawings below are only for reference which might be slightly different from the actual object, please in kind prevail. Any tools missing
or installation problems, please contact the customer service firstly.
A
B
C
x4
x8
x4
M6x12
M6x20
ST4.2x32
Part List
Qty
No.
Part
No.
Part
1
1
2
Left lifting
Tabletop set
column set
3
2
4
Feet
Power plug
5
6
4
Cable management
Lifting column cover
7
8
2
Feet cover
Switch cord
9
10
1
Handset
ST4.2x19
Installation guide
Technical Data
Item No.
SPE-G110
Column Design
2-stage & enhanced column
Maximum Lo ad
50KG
Max Speed
25mm/s
Highest Position
1255mm
Lowest Position
755mm
Height range
500mm
Inner tube
70mmx40mmx2mm
Outer tube
75mmx45mmx1.5mm
Desktop
1200mmx600mmx25mm MDF
D
x1
4x4
5x5(With cross)
Installation Instruction
1
Qty
2
1
2
4
5
2
6
1
7
3
2
10
STEP1
A
x4
M6x12
D
x1
4x4
longside of the
lifting column
D
A
Shortside of the desktop
STEP2
B
x8
M6x20
C
x4
ST4.2x32
D
x1
5x5(With cross)
D
x1
4x4
STEP3
D
x1
5x5(With cross)
9
2
8
Install the left column
Install the lifting column
1
Rotate the column after
inserting it to the bottom
to avoid height difference
1.Insert the column coupling into the
gear box as shown in the figure.
3
3. Rotate it as shown in the figure. Then use 4x4
Note: The method of installing the left column is
allen key to tighten two M6x12 screws. The
the same as that of the right column, and the
installation completes.
direction is the same.
Install the feet
D
C
B
Install the key button
2
Insert
2.Rotate the left column to the position shown
in the figure to avoid the screws, and rotate it
counterclockwise after fully inserting it.
4
D
A
Tighten
4. The installation of the other side column
is the same as that of the left column, and
the direction is the same.
Connect the feet to the column, use a 4x4 wrench
to screw M6x20 and tighten them, and use a 5x5
wrench to screw ST4.2x32 self-tapping screws to
fix the lifting column cover and the feet cover.
Place the key button in the position shown in the figure, align the
two holes of the table as shown in the figure, and not align the
other holes. Use a 5x5 hex wrench with a cross to screw two
ST4.2x19 self-tapping nails and fix them.
D
10
Advertisement
Related Manuals for Spacetronik SPE-G110
Summary of Contents for Spacetronik SPE-G110
- Page 1 Install the left column STEP1 Install the lifting column Item No.: SPE-G110 Installation guide Rotate the column after Insert inserting it to the bottom M6x12 to avoid height difference 2.Rotate the left column to the position shown 1.Insert the column coupling into the in the figure to avoid the screws, and rotate it gear box as shown in the figure.
- Page 2 STEP4 Install the cables Removable Stick “▲” ● “▼” ● Instruction Lifting Function: adjust the height of desk by pressing the button“▲”or ”▼” Reset Function: (1) When at the lowest position, long press the button ”▼” for more than 5 seconds to enter the reset state. The reset is completed until the lifting system hits the bottom and rebounds to stop.
Need help?
Do you have a question about the SPE-G110 and is the answer not in the manual?
Questions and answers