Page 2
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without notice. Every precaution has been taken in the preparation of this manual. Neverthe- less, OMRON assumes no responsibility for errors or omissions.
Introduction Introduction Thank you for purchasing an NA-series Programmable Terminal. This manual contains information that is necessary to use the NA-series Programmable Terminal. Please read this manual and make sure you understand the functionality and performance of the NA-series Programmable Terminal before you attempt to use it in a control system. Keep this manual in a safe place where it will be available for reference during operation.
Relevant Manuals Relevant Manuals The basic information required to use an NA-series PT is provided in the following four manuals. • NA-series Programmable Terminal Hardware User’s Manual (Cat. No. V117) • NA-series Programmable Terminal Hardware(-V1) User's Manual (Cat. No. V125) •...
Manual Structure Manual Structure Page Structure and Markings The following page structure is used in this manual. Level 1 heading 3 Installation and Wiring Level 2 heading Installing NA-series PTs Level 3 heading Level 2 heading Give the current headings. Level 3 heading 3-3-1 Installation in a Control Panel...
Page 6
Manual Structure Special Information Special information in this manual is classified as follows: Precautions for Safe Use Precautions on what to do and what not to do to ensure safe usage of the product. Precautions for Correct Use Indicates precautions on what to do and what not to do to ensure proper operation and perfor- mance.
Sections in this Manual Sections in this Manual Introduction to the NA-series Programmable Terminals Configuration Units Installation and Wiring System Program Troubleshooting Maintenance Appendices Index NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
Page 8
Sections in this Manual NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
CONTENTS CONTENTS Introduction ......................1 Relevant Manuals..................... 2 Manual Structure...................... 3 Sections in this Manual ................... 5 Terms and Conditions Agreement ................11 Safety Precautions....................13 Precautions for Safe Use ..................16 Precautions for Correct Use ................. 19 Regulations and Standards .................. 20 Conformance to Shipbuilding Standards ............
Page 10
CONTENTS USB Memory Devices......................2-11 2-3-1 Models and Specifications ......................2-11 2-3-2 Applications..........................2-11 2-3-3 Installing and Removing......................2-11 Support Software......................... 2-13 2-4-1 Connection Methods ......................... 2-13 Section 3 Installation and Wiring Processing at Power ON and Power OFF ................3-2 3-1-1 Power ON Operation........................
Page 11
CONTENTS Section 5 Troubleshooting Operation after an Error ......................5-2 5-1-1 Checking NA Unit Status ......................5-2 5-1-2 Fatal Errors in the NA Unit......................5-3 5-1-3 Nonfatal Errors in the NA Unit ....................5-4 Troubleshooting ........................5-5 5-2-1 Confirming NA Unit Operation ....................5-5 5-2-2 Correcting Fatal Errors in the NA Unit ..................
Omron’s exclusive warranty is that the Products will be free from defects in materials and workman- ship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied.
Page 14
Disclaimers Performance Data Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual perfor- mance is subject to the Omron’s Warranty and Limitations of Liability.
Safety Precautions Safety Precautions Definition of Precautionary Information The following notation is used in this manual to provide precautions required to ensure safe usage of the NA-series Programmable Terminal. The safety precautions that are provided are extremely impor- tant to safety. Always read and heed the information provided in all safety precautions. The following notation is used.
Page 16
Safety Precautions Warnings WARNING Do not attempt to take the NA Unit apart and do not touch the product inside while the power is being supplied. Otherwise it may result in electric shock. Always ensure that the personnel in charge confirm that installation, inspection, and maintenance were properly performed for the NA Unit.
Page 17
Safety Precautions Precaution WARNING Wiring Observe the following precautions when wiring the NA5-W-V1. The internal power supply in the NA5-W-V1 is a non-isolated DC power supply. Never ground the 24 V side. If the 24 V power supply to the NA is grounded positively, a short circuit will occur as shown below and may result in damage to the device.
Precautions for Safe Use Precautions for Safe Use • When unpacking the NA Unit, check carefully for any external scratches or other damages. Also, shake the NA Unit gently and check for any abnormal sound. • The NA Unit must be installed in a control panel. •...
Page 19
Precautions for Safe Use • Disconnecting the cable between a support tool and the NA Unit. • Do not connect an AC power supply to the DC power terminals. • Do not perform a dielectric strength test. • Use a DC power with a slight voltage fluctuation and that will provide a stable output even if the input is momentarily interrupted for 10 ms.
Page 20
Precautions for Safe Use • To ensure the system's safety, make sure to incorporate a program that call periodically signals dur- ing the operation at connected device side and can confirm the normal functionality of the NA Unit before running the system. •...
Precautions for Correct Use Precautions for Correct Use Do not install or store the NA Unit in any of the following locations: • Locations subject to severe changes in temperature • Locations subject to temperatures or humidity outside the range specified in the specifications •...
Concepts EMC Directive OMRON devices that comply with EU Directives also conform to the related EMC standards so that they can be more easily built into other devices or the overall machine. The actual products have been checked for conformity to EMC standards.* Whether the products conform to the standards in the system used by the customer, however, must be checked by the customer.
Page 23
Regulations and Standards Conformance to KC Standards When you use this product in South Korea, observe the following precautions. This product meets the electromagnetic compatibility requirements for business use. There is a risk of radio interference when this product is used in home. NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
The NA-series Programmable Terminals comply with shipping standards. Application conditions are set for compliance for individual shipping standards, and it may not be possible to use the product in some installation locations. Contact an OMRON sales representative before using the product. International Shipping Standards...
Page 25
Conformance to Shipbuilding Standards Certification Zones for Shipping Standards b. Bridge Air conditioning a. Deck No air conditioning Devices on deck or bridge Devices not on deck or bridge Ocean e. Boiler room c. Depends on ship type d. Engine room Air conditioning Emergency power supply devices on No air conditioning...
Related Manuals Related Manuals The following manuals are related to the NA-series PTs. Use these manuals for reference. Manual name Cat. No. Models Applications Description NA-series Program- V117 NA5-W Learning the speci- Information is provided on NA-series mable Terminal Hard- fications and set- PT specifications, part names, instal- ware User’s Manual...
Page 27
Related Manuals Manual name Cat. No. Models Applications Description NX-series CPU Unit W535 NX701- Learning the basic An introduction to the entire NX-series Hardware User's specifications of system is provided along with the fol- Manual the NX-series CPU lowing information on the CPU Unit. Units, including •...
Page 28
Related Manuals Manual name Cat. No. Models Applications Description CJ Series Program- W393 CJ1H-CPUH-R Learning the basic The following information is provided mable Controllers specifications of on a CJ-series PLC. CJ1G/H-CPUH Operation Manual the CJ-series • Introduction and features CJ1G-CPUP PLCs, including •...
Page 29
Related Manuals Manual name Cat. No. Models Applications Description CS/CJ/NSJ Series W342 CS1G/H-CPUH Learning detailed 1) C-mode commands and 2) FINS Communications specifications on commands are described in detail. CS1G/H-CPU-V1 Commands Refer- the communica- Refer to this manual for information CS1D-CPUH ence Manual tions instructions...
Page 30
Related Manuals Manual name Cat. No. Models Applications Description CS/CJ-series Ether- W465 CJ2H-CPU6-EIP Learning how to Information is provided on the built-in Net/IP™ Units Oper- use the built-in Eth- EtherNet/IP port and EtherNet/IP CJ2M-CPU3 ation Manual erNet/IP port of the Units.
Page 31
Related Manuals Manual name Cat. No. Models Applications Description NY-Series IPC W557 NY532-1 Learning the basic An introduction to the entire NY-series Machine Controller specifications of system is provided along with the fol- Industrial Panel PC the NY-series lowing information on the Industrial Hardware User's Industrial Panel Panel PC.
Page 32
NJ-series Robot Inte- O037 NJ501-R Using the Describes the settings and operation grated CPU Unit NJ-series Robot of the CPU Unit and programming User’s Manual Integrated CPU concepts for OMRON robot control. Unit. NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
Term Description A general term for interface devices that indicates both hardware and software elements. In this manual, “HMI” refers to an OMRON Sysmac-brand product unless otherwise specified. The hardware elements of the HMI. NA Series The NA Series of Programmable Terminals and peripheral devices.
Revision History Revision History A manual revision code appears as a suffix to the catalog number on the front and back covers of the manual. V125-E1-02 Cat. No. Revision code Revision code Date Revised content April 2020 Original production April 2021 Made revisions accompanying version upgrade.
Introduction to the NA-series Pro- grammable Terminals This section describes the features, basic system configuration, specifications, and overall operating procedure of the NA-series Programmable Terminals. 1-1 NA-series Programmable Terminals ......1-2 1-1-1 Features .
They provide all of the functions of traditional programmable terminals with a clearer, easy-to-use interface. OMRON offers the new Sysmac Series of control devices designed with unified communications speci- fications and user interface specifications. The NA-series Programmable Terminals are Sysmac devices that you can use together with the NJ/NX/NY-series Machine Automation Controllers and the Sysmac Studio Automation Software to achieve optimum functionality and ease of operation.
Page 37
1 Introduction to the NA-series Programmable Terminals Standard-feature SD Memory Card Slot You can use an SD Memory Card inserted in the NA Unit to automatically transfer the project you created on the Sysmac Studio to the NA Unit, to update the system program in the NA Unit, or to save the log data from the NA Unit.
1 Introduction to the NA-series Programmable Terminals System Configurations The section describes the system configurations of an NA-series PT. 1-2-1 Connecting to the Support Software You can connect the Sysmac Studio to a USB port on the NA Unit with a commercially available USB cable.
1-3-1 NA Units Case Display Data Power con- Model Weight Appearance Color panel capacity sumption NA5-15W101S-V1 Silver 15.4 inches 29 W max. 3.2 kg max. NA5-15W101B-V1 Black NA5-12W101S-V1 Silver 12.1 inches NA5-12U101S 25 W max. 2.4 kg max. 256 MB...
1 Introduction to the NA-series Programmable Terminals 1-3-3 Other Optional Products SD Memory Cards Model Appearance Capacity HMC-SD291 2 GB HMC-SD491 4 GB USB Memory Devices Model Appearance Capacity FZ-MEM2G 2 GB FZ-MEM8G 8 GB Other Products Name Model Appearance Specifications Battery Set CJ1W-BAT01...
1.4 kg max. Front-panel controls: IP65 oil-proof type, UL Type 4X (at initial state) Degree of pro- To reinstall the NA Unit in a panel, contact your OMRON representative for replacement of tection the rubber packing. Battery life: 5 years at 25°C The RTC will be backed up for 5 days after the battery runs low.
Page 42
1 Introduction to the NA-series Programmable Terminals Specification Item NA5-15W-V1 NA5-12W-V1 NA5-9W-V1 NA5-7W-V1 UL61010-2-201/CSA C22.2 NO.61010-2-201:14 EMC Directive (2014/30/EU) EN 61131-2:2007 Shipbuilding standards LR, DNV, and NK International IP65 oil-proof, UL Type 4X (front panel only) standards UL 121201, 9th Edition/CSA C22.2 NO.213-2017 EAC IEC61131-2:2007 KC Standards KN61131-2 2018 RCM EN61000-6-4:2007+A1:2011...
Page 43
Temperature [°C] *4. Check with your OMRON representative or refer to the following OMRON website for the latest information on the applicable standards for each model: www.ia.omron.com. *5. Use power supply Class 2 to conform to UL Standards.
NA5-9W-V1 NA5-7W-V1 *2. The backlight can be replaced at an OMRON maintenance base. The backlight is LED type. *3. This is the estimated time before brightness is reduced by half at room temperature and humidity. The life expectancy is drastically shortened if PT is used at high temperatures.
Page 45
1 Introduction to the NA-series Programmable Terminals Data Capacity Specification Item NA5-15W NA5-12W NA5-9W NA5-7W User data capacity 256 MB External Interfaces Item Specifications (Same for all models.) Ethernet ports Applications Port 1: Connecting to anything other than the Sysmac Studio, e.g., device connections and VNC clients Port 2: Connecting to the Sysmac Studio in addition to the applications of port 1.
Page 46
1 Introduction to the NA-series Programmable Terminals 1 - 12 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
Configuration Units This section describes the basic system configuration and devices used for NA-series Programmable Terminals. 2-1 NA Units ........... . . 2-2 2-1-1 Components and Functions .
2 Configuration Units NA Units This section describes the names and functions of NA Unit parts and installation methods and provides other information. 2-1-1 Components and Functions Front Panel RUN indicator Display F1 Key F2 Key F3 Key Function keys Name Description ...
Page 49
2 Configuration Units Precautions for Safe Use • Do not press the touch panel with a force greater than 30 N. • The deterioration over time may cause the touch points to move on the touch panel. Cali- brate the touch panel periodically. •...
Page 50
2 Configuration Units Back Panel • Back Panel (a) Battery cover (b) ID information label NA5- • Bottom Panel (e) Ethernet ports (f) Serial port (for future expansion) (d) Protective ground connector (c) SD Memory (g) USB host port Card connector (h) USB slave port (j) DC input terminals...
Page 51
2 Configuration Units Name Description Battery cover Open this cover to replace the Battery. ID information label You can check the ID information of the NA Unit. SD Memory Card connector Insert an SD Memory Card here. Protective ground terminal Use for protective grounding.
Page 52
2 Configuration Units Protective Ground Terminal 24VDC 24VDC Pin No. Signal name Name Protective ground Reset Switch Use a precision screwdriver or similar device with a diameter of less than 2.4 mm. The reset switch performs the same function as cycling the power supply. ...
Page 53
2 Configuration Units • Connecting Devices That Support IEEE 802.3i (10BASE-T) or IEEE 802.3u (100BASE-TX) Pin No. Signal name Name Twisted-pair output (differential output) Twisted-pair output (differential output) Twisted-pair input (differential input) BI D+ Protection circuit BI D- Protection circuit Twisted-pair input (differential input) BI D+ Protection circuit...
Page 54
Give the MAC addresses of the Ethernet ports. Lot number Gives the lot number of the NA Unit. DDMYY: Lot number, : For use by OMRON M is 1 to 9 for January to September, X for October, Y for November, and Z for December.
SD and SDHC memory cards are supported, but use the OMRON-specified SD Memory Cards. (Refer to 1-3-3 Other Optional Products on page 1-6.) OMRON is not responsible for the operation, perfor- mance, or write life of any other memory card.
Page 56
2 Configuration Units • Never insert the SD Memory Card facing the wrong way. If the SD Memory Card is inserted forcibly, it may become unusable. • To format the SD Memory Card (e.g., to delete all of the data), use the SD Formatter for SD/SDHC/SDXC provided by the SD Association.
USB Memory Devices that comply with the USB 2.0 standard are supported, but use one of the USB Memory Devices specified by OMRON. (Refer to 1-3-3 Other Optional Products on page 1-6.) OMRON is not responsible for the operation, performance, or write life of any other USB Memory Device.
Page 58
2 Configuration Units Installing the USB Memory Device Insert the USB Memory Devices into the USB host port on the back of the NA Unit. NA5- Push the USB Memory Device all of the way in. Removing the USB Memory Device Execute EjectUSBDevice in a subroutine and then remove the USB Memory Device.
2 Configuration Units Support Software This Sysmac Studio is used to create, debug, and maintain applications for NA-series Programmable Terminals. 2-4-1 Connection Methods With an NA-series Programmable Terminal, you can connect the Sysmac Studio online in the following ways. Connecting with USB Use a commercially available USB cable for a USB connection.
Page 60
2 Configuration Units Connecting with Ethernet You can use a direct connection or connect through an Ethernet switch by connecting to Ethernet port 2 on the NA Unit. Back Panel of NA Unit Sysmac Studio Ethernet cable (direct connection or connection Connect to Ethernet port 2 (on the right).
Page 61
Installation and Wiring This section describes how to install and wire an NA Unit. 3-1 Processing at Power ON and Power OFF ......3-2 3-1-1 Power ON Operation .
3 Installation and Wiring Processing at Power ON and Power WARNING Do not attempt to disassemble, repair, or modify the NA Unit. It may cause NA Unit to lose its safety function. Do not attempt to take the NA Unit apart and do not touch the product inside while the power is being supplied.
3 Installation and Wiring Fail-safe Measures WARNING Provide safety measures in external circuits to ensure safety in the system if an abnormality occurs due to malfunction of the NA Unit or due to other external factors affecting operation. Not doing so may result in serious accidents due to incorrect operation. The circuits associated with safety measures, such as emergency stop circuits, interlock cir- cuits, and limit circuits, must be provided in external control circuits.
3 Installation and Wiring Installing NA Units This section describes how to install an NA Unit. Precautions for Correct Use • Follow the instructions in this manual to correctly perform installation. • Do not install or store the NA Unit in any of the following locations: •...
3 Installation and Wiring 3-3-1 Installation in a Control Panel Installation in a Control Panel The NA Unit is installed by embedding it in a control panel. Panel Mounting Brackets and a Phillips screwdriver are required to mount the NA Unit. The required number of Panel Mounting Brackets are included with the NA Unit.
Page 66
3 Installation and Wiring Slide the PWA over the NA Unit from the back until the flat side of the PWA is flat against the inside of the panel, as shown in the following figure. Attach the panel mounting brackets from the back of the panel as shown in the following figure. The number of mounting brackets depends on the size of the NA Unit, as shown in the following table.
Page 67
3 Installation and Wiring Precautions for Safe Use • Do not let metal particles enter the NA Unit when preparing the panel. • To conform to UL Type 4X standards, the thickness must be 1.6 to 4.5 mm. To conform to UL Type 4X standards, always use the NA5-W-V1 with a High-pressure Waterproof Attachment (PWA).
Page 68
3 Installation and Wiring Additional Information Bracket Mounting Locations for Different Units When you mount an NA Unit, secure it with the mounting brackets as shown in the following fig- ures. • NA5-15W-V1 Secure the NA Unit with mounting brackets in the eight locations shown below. •...
3 Installation and Wiring Wiring Methods This section describes how to wire an NA Unit. WARNING Make sure that the voltage and current that are input to the NA Unit are within the specified ranges. Inputting voltages or currents that are outside of the specified ranges may cause acci- dents or fire.
Page 70
3 Installation and Wiring Wiring Materials Use the enclosed power supply connector to connect the power supply to the NA Unit. • We recommend that you use a power supply cable with the following stranded wires. Wire the power supply giving sufficient consideration to the voltage drop and heat generation for the cable length in the installation environment.
Page 71
3 Installation and Wiring Wiring Procedure Use the following procedure to connect the power supply. Remove the sheath from the power supply wires. 7 mm Remove the power supply connector from the NA Unit and loosen the terminal block screws. Insert the wires all the way to the back of the connector and then turn the screws clockwise to secure the wires.
3 Installation and Wiring Precautions for Correct Use Observe the following precautions to prevent broken wires. • When you remove the sheath, be careful not to damage the conductor. • Connect the conductor without twisting the wires. • Do not weld the conductors. If you do so, vibration may cause the wires to break. •...
3 Installation and Wiring Control Panel Installation To ensure system reliability and safety, the system must be designed and configured according to the installation environment (temperature, humidity, vibration, shock, corrosive gases, overcurrent, noise, etc.). 3-5-1 Temperature Panels have been reduced in size due to space-saving and miniaturization in devices and systems, and the temperature inside the panel may be at least 10 to 15°C higher than outside the panel.
3 Installation and Wiring Forced Air Circulation (with Fan in Closed Panel) NA Unit Forced Circulation Room Cooling (Cooling the Entire Room Where the Control Panel Is Located) Cooler NA Unit Control panel Room Cooling 3-5-2 Humidity Rapid temperature changes can cause condensation to occur, resulting in malfunctioning due to short-circuiting.
3 Installation and Wiring 3-5-3 Vibration and Shock The NA Unit is tested for conformity with the sine wave vibration test method (IEC 60068-2-6) and the shock test method (IEC 60068-2-27) of the Environmental Testing for Electrotechnical Products. It is designed so that malfunctioning will not occur within the specifications for vibration and shock.
3 Installation and Wiring 3-5-5 Electrical Environment When installing or wiring devices, make sure that there will be no danger to people and that noise will not interfere with electrical signals. Installation Locations for NA Unit Install the NA Unit as far away as possible from high-voltage (600 V or higher) and power devices to ensure safe operation and maintenance.
Page 77
3 Installation and Wiring External Wiring Wiring, and noise countermeasures in particular, must be based mostly on experience, and it is neces- sary to closely manage wiring based on information in the manuals. Wiring Routes Each of the following combinations includes different signal types, properties, or levels. They will cause the signal-to-noise ratio to drop due to factors such as electrical induction.
Page 78
3 Installation and Wiring • To avoid overheating the conduits when using conduits for wiring, do not place wires for a single circuit in separate conduits. Power supply Load Incorrect Power supply Load Correct Power supply Load Correct Parallel Wiring (Single Phase) •...
3 Installation and Wiring 3-5-6 Grounding Grounding has the following two purposes. • Protective Grounding Protective grounding is done to ensure safety. It is intended to prevent electrical shock by holding the electrical potential at the grounding potential that is generated by factors such as leakage, induction, or failure.
Page 80
3 Installation and Wiring 2. Functional ground For the grounding wiring, refer to 3. Grounding Wiring on page 3-20. • Applicable Wire Size Conductor cross-section AWG #12 to 22 0.35 to 3.31 mm • Screw Tightening Torque 0.5 to 0.6 N·m •...
Page 81
3 Installation and Wiring 4. NA Unit internal grounding connection diagram NA5-@@W@@@@-V1 Non-isolated power TVS clamping diode supply 35 V Gas Discharge Tube 470 V Serial USB slave connector connector hood hood Ethernet connector USB host hood connector 24 VDC PE (Protective ground) hood FG (Functional ground)
System Program This section describes the system program that is used by NA-series Programmable Terminals. 4-1 System Program and NA Unit Startup Status ..... . . 4-2 4-2 System Recovery .
4 System Program System Program and NA Unit Startup Status The system program is required to start the NA Unit and execute the project in the NA Unit. • The system program automatically starts when you turn ON the power supply to the NA Unit or when you press the reset switch while power is supplied.
4 System Program System Recovery You can implement system recovery if the NA Unit will not start normally or if you want to initialize the contents of the NA Unit to the default state. When you implement system recovery, all of the user data is deleted from the NA Unit and the system program is overwritten with the newest version.
Page 86
4 System Program Insert the media that you prepared in step 2 into the NA Unit and turn ON the power supply to the NA Unit. Tap the language to use for system recovery. Select the package that you want to install, and then tap the Install Button. Tap the Yes Button.
Page 87
4 System Program When the following message is displayed, remove the media from the NA Unit and turn OFF the power supply to the NA Unit. Open the battery cover on the back of the NA Unit and set the DIP switch to the settings shown below.
4 System Program System Menu Overview You can use the System Menu to perform operations according to on-screen displays to perform vari- ous settings for the NA Unit. Refer to 4-3-1 System Menu Configuration on page 4-6 for the configuration of the System Menu. Refer to 4-3-2 Using the System Menu on page 4-9 for the procedures to use the System Menu.
Page 89
4 System Program • Project System Menu (2/2) Item Description Reference Print Settings Sets up printing/capturing of the NA screens. P. 4-29 Buzzer Settings Sets buzzer sounds. P. 4-30 Operation Log Viewer Displays the Operation Log Viewer. P. 4-31 Safety Monitor Displays the Safety Monitor.
Page 90
4 System Program • Device System Menu Item Description Reference Date & Time Settings Sets the date and time, as well as settings for synchronization P. 4-48 with the time server. Language Settings Makes settings for the system language. P. 4-48 Interface Settings Makes settings for the NA Unit interface.
4 System Program 4-3-2 Using the System Menu This section describes how to use the System Menu, including the display methods and how to select menu items. Additional Information The system settings that are made in the Sysmac Studio project data take priority over the set- tings that are made from the System Menu.
Page 92
4 System Program Selecting Menu Items Tap a menu item or icon on the System Menu to display the corresponding functionality. Example: Tap the Hardware Diagnostics Icon on the Device System Menu to display the Hardware Diagnostics Screen. Leaving the System Menu to Enter Operating Status Tap the Exit Button on the Project System Menu to return to Run Status.
4 System Program System Menu Details This section describes the functions that are provided by the System Menu. 4-4-1 Display Settings (Project System Menu) You can use the display settings to set the following items. Item Description Screen Saver Enabled Select this check box to use the screen saver.
4 System Program 4-4-2 Language Settings (Project System Menu) You can use the language settings to set the following items. Item Description User Language Sets the user language. System Language Displays the system language that is associated with the user lan- guage.
4 System Program 4-4-4 User Accounts (Project System Menu) You can use the user account settings to set the following items. Precautions for Safe Use • When you change a password, do not reset the NA Unit or turn OFF the power supply before writing the new password is completed.
4 System Program 4-4-5 NJ/NX/NY Troubleshooter (Project System Menu) The NJ/NX/NY Troubleshooter can be used to access descriptions and countermeasures for errors and events that occur in the Controller and built-in devices. These functions can be used only when you are connected to an NJ/NX/NY-series Controller.
Page 97
4 System Program When Connected to an NJ-series CPU Unit Troubleshooter functions System configuration element Displaying Clearing Displaying Clearing error errors errors error logs logs CPU Rack CPU Unit Applicable CJ-series Units Applicable Partially applicable EtherCAT Slaves (Sysmac devices) *2 *3 Applicable Applicable Applicable...
Page 98
4 System Program When Connected to an NX-series Communication Control Unit Troubleshooter functions System configuration element Displaying Clearing Displaying Clearing error errors errors error logs logs Communication Control Unit Applicable NX Units Partially appli- *2*3 Applicable Applicable Applicable cable *1. Events are not displayed for some NX Units. *2.
Page 99
4 System Program Starting and Quitting the NJ/NX/NY Troubleshooter There are four ways to start the NJ/NX/NY Troubleshooter. • Select NJ/NX/NY Troubleshooter from the System Menu. • Execute the ShowTroubleshooter action. • Execute the ShowTroubleshooter function. • Set the Troubleshooter operation settings to specify monitoring user-defined or Controller errors. (The NJ/NX/NY Troubleshooter will be displayed automatically when a user-defined error or Control- ler error occurs.) ...
Page 100
4 System Program Starting from a User Screen The required settings must be made from the Sysmac Studio. The following example shows how to execute the Troubleshooter by using an object event. In this example, settings are performed to execute the Troubleshooter when a Button object is clicked.
Page 101
4 System Program Additional Information If you use runtime version 1.02 or if you do not specify a name for ControllerName, a Controller status list is displayed on the screen when the Troubleshooter is activated. Starting the Troubleshooter for User-defined Errors or Controller Errors The required settings are made from the Sysmac Studio.
Page 102
4 System Program Quitting the NJ/NX/NY Troubleshooter Click the Exit Button on the screen that was displayed when the NJ/NX/NY Troubleshooter started. The display will return to the user screen that was displayed before the NJ/NX/NY Trouble- shooter started. NJ/NX/NY-series Controller Status Screen The status of the host to which the NA is currently connected is displayed.
Page 103
4 System Program Controller Event List Screen This screen displays a list of the Controller errors for the selected host. Item Description Exit Button Quits the Troubleshooter. Title Bar Displays the current date of the NA. Tabs Switch between displaying active events and the event log. Controller Events Displays current Controller events.
Page 104
4 System Program Controller Event Log Screen This screen displays a list of the Controller events for the selected host. Item Description Exit Button Quits the Troubleshooter. Tittle Bar Displays the current date of the NA. Tabs Switch between displaying active events and the event log. Controller Events Displays current Controller events.
Page 105
4 System Program Event Source Selection Screen On this screen, the Functional Modules that are the sources of the errors are selected. Item Description Functional Module List Displays a list of the Functional Modules in the Controller. Sub Functional Module List Displays a list of the Sub Functional Modules in the Controller.
Page 106
4 System Program Details Screen This screen displays detailed information on errors or events. Item Description Tittle Bar Displays the current date of the NA. Back Button Closes the Details Screen. Details Button Displays errors and events in detail. Screen Shot Button Captures an image of the displayed screen and stores it in USB memory or an SD Memory Card in PNG format.
Page 107
4 System Program Operation Settings of the NJ/NX/NY Troubleshooter The operation settings of the NJ/NX Troubleshooter are set from the Sysmac Studio. Double-click Trou- bleshooter under Configurations and Setup in the Multiview Explorer. The Troubleshooter Settings Tab Page will be displayed in the Edit Pane. ...
4 System Program 4-4-6 Alarm Viewer (Project System Menu) The following two functions are provided to display alarms. Item Description Active HMI User Alarms Displays current user alarms. Historical HMI User Alarms Displays the user alarm log. From the Alarm Viewer Screen, you can tap any of the icons for functions to display the individual func- tion screens.
Page 109
4 System Program • Alarm Details Screen This screen displays detailed information on a selected user alarm. Item Description Alarm Code Displays the alarm code of the user alarm that occurred. Additional Information Displays the additional information of the user alarm that occurred. Details Displays the details on the user alarm that occurred.
Page 110
4 System Program • Historical HMI User Alarms Screen This screen displays a log of the user alarms. Item Description Historical HMI User Alarm Displays a log of the user alarms. 4 - 28 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
4 System Program 4-4-7 Project System Menu Settings (Project System Menu) You can use the System Menu settings to set the following items. Item Description Double-tap Interval Sets the double-tap interval for the operation to start the System Menu. Detectable Corner Sets the double-tap detection positions for the operation to start the System Menu.
4 System Program 4-4-9 Buzzer Settings (Project System Menu) You can use the buzzer settings to set the following items. Item Description Touch Input Notification Select this check box to sound the buzzer when an object is touched. Alarm Notification Select this check box to sound the buzzer when an alarm occurs.
Page 113
4 System Program 4-4-10 Operation Log Viewer In the Operation Log Viewer, you can check the logs recorded when operations specified on Sysmac Studio are executed on the NA unit. Starting and Exiting Operation Log Viewer There are three ways to start the Operation Log Viewer as shown below. •...
Page 114
4 System Program Starting from a User Screen The required settings are made from the Sysmac Studio. The following example shows how to execute the Operation Log Viewer by using an object event. In this example, settings are performed to execute Operation Log Viewer when a Button object is tapped.
Page 115
4 System Program Exiting Operation Log Viewer Tap Back on the screen that was displayed when the Operation Log Viewer started. The display will return to the screen that was displayed before the Operation Log Viewer started. 4 - 33 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
4 System Program Operation Log Viewer Displays the operation logs. Item Description Search Searches the specified date and time and then displays the results in the log list. Log List Displays a list of the logs that have been recorded. Date and Time: Displays the local time at which the log was recorded.
Page 117
4 System Program Detail Information Displays detailed information on the log. Item Description Log detail information Displays detailed information on the log. Date and Time: Displays the local time at which the log was recorded. User: Displays the user who executed the operation. Category: Displays the category of the operation executed.
4 System Program 4-4-11 Safety Monitor Safety Monitor provides a function to identify inputs that cause abnormal states when the external out- put from the safety program of the safety control unit is in an abnormal state. Display Item Safety Monitor can display the items below. •...
Page 119
4 System Program System configuration All NA5 Series Programmable Terminals support the Safety Monitor. To use the Safety Monitor, an SD memory card needs to be inserted into the NA unit. The equipment that can be monitored is as follows. ...
Page 120
4 System Program Starting and exiting Safety Monitor There are three ways to start the Safety Monitor as shown below. • Select Safety Monitor from the System Menu. • Execute the StartSafetyMonitor action. • Execute the StartSafetyMonitor function. Starting from the System Menu Display the System Menu and select Safety Monitor.
Page 121
4 System Program Starting from a User Screen The required settings are made from the Sysmac Studio. The following example shows how to use an object event to execute the Safety Monitor. In this example, settings are made to execute the Safety Monitor when a Button object is pressed. Place a Button object on the screen and display Events and Actions.
Page 122
4 System Program Exiting Safety Monitor on the screen that was displayed when the Safety Monitor started. The display will return to the screen that was displayed before the Safety Monitor started. 4 - 40 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
Page 123
4 System Program I/O Matrix Monitor Displays a list of values of variables. In the initial state, only outputs are displayed. Selecting an output displays its related inputs. Item Description Applicable equipment Displays the safety CPU unit currently being monitored. Output from Safety CPU Displays a list of outputs and shows values.
Page 124
4 System Program Safety output unit monitor Displays the status of the safety output unit. Item Description Applicable equipment Displays the CPU unit currently being monitored. Unit information Displays information on the currently displayed safety output unit. Terminal section monitor Displays the output state of the terminal.
Page 125
4 System Program Safety input unit monitor Displays the status of the safety input unit. Item Description Applicable equipment Displays the CPU unit currently being monitored. External equipment setting Displays information on the equipment connected to the terminal. information Displays the name of the equipment, terminal numbers connected, as well as corresponding icons.
Page 126
4 System Program Variable Information Displays detailed information on the variable. Item Description Variable Information Displays detailed information on the variable. Close Closes Variable Information. Search Variable Searches for a variable. Item Description Variable Name Sets the name of the variable to search. Type Selects the type of variables to search.
Page 127
4 System Program PDF Display Displays the files set in PDF Display Settings on the Document Viewer in Windowed mode. The Docu- ment Viewer closes when the Safety Monitor is exited. Menu The following three functions can be executed from the menu. •...
Page 128
4 System Program PDF Display Settings Specify the files to be displayed in PDF Display. Item Description Media Settings Specifies the location where files are saved. For FTP Server settings, inquire to the server administrator. Folder Name Displays the name of the folders displayed in File List. File List Displays a list of folders and files included in the folder.
Page 129
4 System Program Elements of each column are shown below. Rows including the initial row are handled as data and up to 16 rows are loaded. Column Item Description Number PDF File Name Specifies the name of the PDF file to be displayed. Extensions cannot be omitted.
4 System Program 4-4-12 Date & Time Settings (Device System Menu) You can use the date & time settings to set the following items. Item Description Time Zone Sets the time zone. Automatically adjust clock for Select this check box to automatically compensate for daylight sav- ing time.
4 System Program 4-4-14 Interface Settings (Device System Menu) You can use the interface settings to set communications for the NA Unit. From the Interface Settings Screen, you can tap any of the icons for settings to display the individual setting screens.
Page 132
4 System Program Ethernet This screen is used to set the Ethernet port IP address and other settings for Ethernet. Item Description Ethernet Port 1 Settings Sets the IP address and other settings for Ethernet port 1. Ethernet Port 2 Settings Sets the IP address and other settings for Ethernet port 2.
Page 133
4 System Program This screen is used to make settings for VNC. • VNC Settings (1/2) Item Description Enable VNC Server Select this check box to use the VNC. Port No. Sets the port number. Mode Sets the mode. Change Password Select this check box to change the password.
Page 134
4 System Program • VNC Settings (2/2) Item Description Enable registered client login Select this check box to set login restrictions. List of clients Lists the clients registered at present. Edits the selected client. Deletes the selected client. Adds a new client. IP Address Sets the IP address of a client.
Page 135
4 System Program FINS This screen is used to make settings for FINS. Item Description Ethernet Port 1 Settings Sets the FINS network address for Ethernet port 1. The node address is automatically created based on the IP address. Ethernet Port 2 Settings Sets the FINS network address for Ethernet port 2.
4 System Program 4-4-15 Brightness Settings (Device System Menu) You can use the brightness settings to set the following items. Item Description Brightness Sets the screen brightness. 4 - 54 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
4 System Program 4-4-16 Transfer Operations (Device System Menu) This screen is used to transfer the project and other data. You can tap any of the icons for settings to display the individual setting screens. Item Description Transfer User Program to HMI Downloads the project.
Page 138
4 System Program Transfer User Program to HMI This screen is used to download the project from an SD Memory Card or USB Memory Device. Item Description Source Media Sets the media that contains the project to download. Path Displays the path of the folder displayed at (c). Folder Contents Displays the files and folders in the currently open folder.
Page 139
4 System Program Transfer User Program from HMI This screen is used to upload the project to an SD Memory Card or USB Memory Device. Item Description Destination Media Sets the media to which to upload the project. Path Displays the path of the folder displayed at (c). Current Folder Displays the files and folders in the currently open folder.
Page 140
4 System Program Transfer Data to HMI This screen is used to download text, videos, or other data from an SD Memory Card or USB Memory Device. Item Description Data Type Sets the file type. Only files with the specified file type are displayed at (c).
Page 141
4 System Program Transfer Data from HMI This screen is used to upload recipes, videos, or other data to an SD Memory Card or USB Memory Device. Item Description Media Sets the media to which to upload the data. Path Displays the path of the folder displayed at (c).
4 System Program 4-4-17 Hardware Diagnostics (Device System Menu) This screen is used to check the operation of the touch panel and to calibrate it. You can tap any of the icons to access a function. Item Description Function Keys Checks the operation of the function keys.
4 System Program Function Keys This screen is used to check the operation of the function keys. Production Information This screen displays product information. - V1 4 - 61 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
Page 144
4 System Program LCD Display A color bar is displayed. Use this to check the LCD. Tap the screen to move to the next display. Touch Panel Calibration This screen is used to calibrate the touch panel. Tap the plus signs that are displayed. To cancel, double-tap any position.
Page 145
4 System Program Touch Panel Input The locations that are touched are displayed as dots. Use this to check the operation of the touch panel. To end, double-tap any position. 4 - 63 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
4 System Program 4-4-18 Production Information (Device System Menu) This screen displays product information. - V1 4 - 64 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
Troubleshooting This section describes troubleshooting methods for errors that may occur in the NA-series Programmable Terminal. 5-1 Operation after an Error ........5-2 5-1-1 Checking NA Unit Status .
5 Troubleshooting Operation after an Error This section describes the error status of the NA-series Programmable Terminal and the operation that occurs after an error is detected. Refer to 5-2 Troubleshooting on page 5-5 for details on corrections for specific errors. 5-1-1 Checking NA Unit Status You can check the operating status of an NA Unit with the RUN indicator on the right side of the front...
5 Troubleshooting 5-1-2 Fatal Errors in the NA Unit Fatal Errors in the NA Unit Some errors are fatal and prevent the NA Unit from operating. This section describes these fatal errors, which cause the operation of the NA Unit to stop. ...
5 Troubleshooting 5-1-3 Nonfatal Errors in the NA Unit Nonfatal Errors in the NA Unit If there are no problems in the hardware or system program, the NA Unit will operate even if one of these errors occurs. This section describes nonfatal errors. ...
5 Troubleshooting Troubleshooting This section provides basic error identification, troubleshooting flowcharts, and error corrections. Use them when an error occurs in the NA Unit. 5-2-1 Confirming NA Unit Operation When an error occurs in the NA Unit, use the following flowchart to determine whether the error is a fatal error or a non-fatal error.
5 Troubleshooting 5-2-2 Correcting Fatal Errors in the NA Unit Power Supply Error Check the following items: • Is the NA Unit correctly connected to the external DC power supply? • Is the voltage supplied from the external DC power supply within the allowable range? ...
5 Troubleshooting 5-2-4 Causes and Correction When You Cannot Go Online from the Sysmac Studio The following table lists the possible causes when you cannot go online with the NA Unit from the Sys- mac Studio. Cause Description Correction Incorrect settings There is a mistake in the settings that the Refer to Troubleshooting Incorrect Settings or faulty communi-...
Page 154
5 Troubleshooting Troubleshooting Incorrect Settings and Faulty Communications Path This section provides troubleshooting methods for incorrect settings, fault communications paths, and high NA Unit loads. Direct Connection with USB Port Sysmac Studio cannot connect to the NA Unit. Turn ON the power supply to the Is power supplied to the NA NA Unit.
Page 155
5 Troubleshooting Ethernet − Direct Connection Sysmac Studio cannot connect to the NA Unit. Turn ON the power supply to Is power supplied to the the NA Unit . NA Unit? Can the Sysmac Studio go online with the NA Unit ? Insert the cable connectors at the personal computer, Ethernet switches, and the NA Unit until they lock into place.
Page 156
5 Troubleshooting Ethernet − Hub Connection Sysmac Studio cannot connect to the NA Unit. Turn ON the power supply to Is power supplied to the the NA Unit . NA Unit ? Can the Sysmac Studio go online with the NA Unit ? Insert the cable connectors at the personal computer, Ethernet switches, and the NA Unit until they lock into place.
Page 157
5 Troubleshooting Set the IP address for the personal computer. Use Is the same IP address set for the default IP address for the NA Unit or connect more than one node (e.g., the Sysmac Studio to the NA Unit with a USB computer or NA Unit) in the cable and set the required IP address.
5 Troubleshooting 5-2-5 Troubleshooting NA Unit Errors This section describes how to troubleshoot errors in the NA Unit. NA Unit Startup NA Unit symptom Cause Correction The indicator does not Power is not supplied. Confirm the connection location and correctly supply light.
Page 159
5 Troubleshooting Errors during NA Unit Operation Errors Determined from NA Unit Symptoms NA Unit symptom Cause Correction The indicators light red There is not enough Change the project to reduce memory usage. and operation stops. memory. The indicators flash red There is an error in the Replace the SD Memory Card or USB Memory Device and the SD Memory...
Page 160
5 Troubleshooting NA Unit symptom Cause Correction Numeric values cannot The upper/lower limit Check the Minimum Value and Maximum Value proper- be input. check for numeric inputs ties of the object on the Sysmac Studio and correct is operating. them as required. When an object is A communications error Check the connection between the NA Unit and con-...
Page 161
5 Troubleshooting Output message Cause Correction E_SYS_015: The bat- The battery voltage has Replace the battery following the procedure given in tery voltage is low. lowered less than the 6-2 Replacing the Battery on page 6-5 specified value during operation. E_SYS_019: XXX must The filtering conditions for Check the set values of the EndTime and StartTime...
Page 162
5 Troubleshooting Output message Cause Correction E_RCP_001: Failed to A recipe is set incorrectly. Select the correct template when you save the recipe. import Recipe csv file XXX. Ingredients do not match template XXX. E_SYS_999: Runtime Illegal processing was Restart the NA Unit. Exception Caught XXX performed.
Page 163
5 Troubleshooting Error Codes Correspondence Table The displayed error codes depend on the runtime version. A correspondence table is given below: Error codes prior to runtime Error codes for runtime version version 1.03 1.03 or higher ManE202 E_COM_100, E_COM_101, E_COM_102, or E_COM_103 ManE203...
Page 165
Maintenance This section describes the required inspections and maintenance. It also describes the service life and replacement procedure for the Battery. 6-1 Periodic Maintenance and Inspection ......6-2 6-1-1 Preparations for Problems .
6 Maintenance Periodic Maintenance and Inspection Periodic inspections are required in order to maintain the NA-series PT in the best operating condition. 6-1-1 Preparations for Problems Observe the following precautions to enable smooth troubleshooting when problems occur. Backing Up the Sysmac Studio Project Always make a backup of the Sysmac Studio project and store it in a safe place.
Page 167
No visible damage Check visually and replace cables wiring cables. if necessary. User-ser Check the brightness of the The backlight must be Contact your OMRON representa- viceable backlight. sufficiently bright. tive to request replacement. parts Backlight life (at room temperature and...
If you discover a fault in the NA Unit during inspections and must replace the NA Unit, observe the fol- lowing precautions when you replace the NA Unit. • Back up the NA Unit data. If OMRON performs repairs, the data may be deleted. • Do not replace the NA Unit until the power is turned OFF.
6 Maintenance Replacing the Battery The Battery in the NA Unit requires maintenance. (The Battery is for the NA Unit's internal clock.) This section describes how to replace the Battery. 6-2-1 Battery Replacement Purpose of the Battery It is used to maintain the clock information in the NA Unit while the power supply is OFF. The clock will stop if there is no Battery or the Battery has been discharged completely.
6 Maintenance Turn OFF the power supply to the NA Unit. If the NA Unit has not been ON, turn it ON for at least five minutes and then turn it OFF. Open the cover on the NA Unit, disconnect the Battery connector, remove the Battery, and replace it with a new Battery.
Appendices The appendices provide specifications and other information not provided in the body of this manual. A-1 Dimensions ........... A-2 A-1-1 NA Units .
Appendices A-2 Available Products A-2-1 Optional Products Table of Optional Products Name Model Remarks NA-15WKBA04 Anti-reflection Sheets for NA5-15W NA-12WKBA04 Anti-reflection Sheets for NA5-12W Anti-reflection Sheets NA-9WKBA04 Anti-reflection Sheets for NA5-9W NA-7WKBA04 Anti-reflection Sheets for NA5-7W NA-15WATW01 High-pressure waterproofing frame for NA5-15W High-pressure NA-12WATW01 High-pressure waterproofing frame for NA5-12W...
Page 177
Appendices NA-WKBA04 Anti-reflection Sheets Attach a Sheet to the screen to protect against diffused reflections and dirt. The entire Sheet is color- less and transparent. Five Sheets are provided in one set. Dimensions Material Attachment method Polyester film Double-sided tape Dimensions (Unit: mm) Model Specification...
Page 178
Appendices NA-WATW01 High-pressure Waterproof Attachment The High-pressure Waterproof Attachment (PWA) is required to conform to UL Type 4X standards. The mounting panel thickness must be between 1.6 and 4.5 mm. To conform to UL Type 4X standards, always use the NA5-W with a High-pressure Waterproof Attachment (PWA). If you do not use a PWA, there is a risk of water entry, which may cause severe equipment damage.
Page 179
Index I - 1 NA-series Programmable Terminal Hardware(-V1) User’s Manual (V125)
Need help?
Do you have a question about the NA5-15W101S-V1 and is the answer not in the manual?
Questions and answers