Page 2
Publications for this product are available by scanning the barcode or visiting www.renishaw.com/olp40. Für dieses Produkt stehen weitere Informationen zur Verfügung. Scannen Sie dazu den Barcode oder besuchen Sie www.renishaw.de/olp40. Para acceder a las publicaciones sobre este producto escanee el código de barras o visite www.renishaw.es/olp40.
Page 3
Dostęp do dokumentacji tego produktu można uzyskać, skanując kod kreskowy lub odwiedzając witrynę www.renishaw.pl/olp40. Publikace pro tento produkt jsou k dispozici po naskenování QR kódu nebo na stránce www.renishaw.cz/olp40. Если вас интересует информация об этом продукте, отсканируйте штрих-код или посетите сайт...
Page 7
CAUTION Remove the battery isolation device from the battery compartment before use. Take care not to short the battery contacts ¬ as this may be a fire hazard. Ensure the contact strips are located securely. ¬...
Page 8
Configuring the probe The following sections describe the process of reviewing and configuring the probe settings. The Trigger Logic™ app simplifies this process with clear, interactive instructions and informative videos.
Page 10
Reviewing the probe settings Key to the symbols LED short flash > 5 s LED long flash × LED check Switch-off method Optical off Short timeout Medium timeout Long timeout 12 s 33 s 134 s Enhanced trigger filter setting 0 ms 10 ms...
Page 11
Optical transmission method Legacy (start filter) Modulated PROBE Optical power Standard Ultra low Battery status Battery good Battery low Probe in standby mode (after 8 seconds)
Changing the probe settings LED check > 5 s Deflect the stylus and hold it deflected until after the battery status has been Key to the symbols displayed at the end of the review sequence. LED short flash LED long flash Deflect the stylus for less than 4 seconds Battery status to move to the next menu option.
Page 14
Switch-off method Optical off Short timeout Medium timeout Long timeout 12 s 33 s 134 s Enhanced trigger filter 0 ms 10 ms Optical transmission method Legacy (start filter) Modulated PROBE...
Page 15
Optical power Standard Ultra low Return to “Switch-off method” New settings complete...
Page 16
Mounting the probe on a shank × 2 2 mm A/F × 2 2 mm A/F × 4 × 4...
Page 22
OMM-2 visual diagnostics NOTE: The appearance of your OMM-2 ACTIVE SYSTEM LED may differ slightly from that shown. Probe 1 Probe 2 SIGNAL LED Probe 3 Signal good Interference or weak signal START LED No signal Start ERROR LED LOW BATTERY LED Signal from probe has either failed or stopped Battery low...
Page 23
OMI-2 / OMI-2T / OMI-2H visual diagnostics PROBE 2 PROBE 1 NOTE: The appearance of your OMI-2 / OMI-2T / OMI-2H may differ slightly from OMI-2T / OMI-2H only OMI-2T / OMI-2H only that shown. SIGNAL LED Signal good Interference or weak signal START LED No signal...
RENISHAW and the probe symbol used in the RENISHAW China RoHS logo are registered trade marks of Renishaw plc in the United Kingdom and other countries. apply innovation and names and For more information on China RoHS visit: designations of other Renishaw products and technologies are www.renishaw.com/mtpchinarohs.
No. 1907/2006 (“REACH”) relating to products containing substances of very high concern (SVHCs) is available at: www.renishaw.com/REACH Renishaw plc declares under its sole responsibility that the OLP40 is in conformity with all relevant Union legislation. FCC Information to user (USA only) The full text of the EU declaration of conformity is available at: www.renishaw.com/mtpdoc...
Page 27
To reduce the risk of negative effects on the environment and human health which could shipment delays, if you need to return the OLP40 to Renishaw for otherwise arise from inappropriate waste handling. Contact your any reason, do not return any batteries.
Page 28
• cables must not be routed alongside high current sources, i.e. The OLP40 has a glass window. Handle with care if broken to motor power supply cables etc, or be near high-speed data avoid injury. lines;...
Page 31
Patents Features of and features of similar products are OLP40 the subject of one or more of the following patents and/or patent applications: EP 1130557 JP 3967592 EP 1185838 JP 4754427 EP 1373995 JP 4773677 EP 1477767 JP 4851488 EP 1477768...
Page 32
Renishaw plc +44 (0)1453 524524 +44 (0)1453 524901 New Mills, Wotton-under-Edge uk@renishaw.com Gloucestershire, GL12 8JR United Kingdom www.renishaw.com For worldwide contact details, visit www.renishaw.com/contact *H-5625-8500-05*...