Specifications
The specifications of the projector are as follows.
Power supply
Power consumption
Power consumption (during
standby)
Size
DLP chip
Display system
Number of pixels 2 304 000 pixels (1 920 x 1 200 dots)
Lens
Light source
Light output
Center to corner zone ratio
*1
Contrast ratio
*1
Color system
Projected image size
Image aspect ratio
Projection method
Power cord length
Outer case
Outer color
Width
Dimensions
Height
Depth
Weight
Noise level
*1
Laser Class
Laser
Classification
Risk Group
Operating
environment
temperature
Operating
environment
Operating
environment
humidity
Power supply
Operating range
Remote
control
Weight
Dimensions
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2020 international standards.
*2 When a projection lens other than ET-D75LE95, ET-D75LE90 is used
*3 When the Zoom Lens (Model No.: ET‑D3LET80, ET‑D75LE8) is used, the projected image size for the maximum projection distance will be 1.78 m
(70") to 15.24 m (600").
When the Zoom Lens (Model No.: ET‑D3LEW200) or the Fixed‑focus Lens (Model No.: ET‑D3LEU100) is used, the projected image size for the
maximum projection distance will be 5.08 m (200") to 15.24 m (600").
When the Fixed‑focus Lens (Model No.: ET‑D75LE95, ET‑D75LE90) is used, the projected image size for the maximum projection distance will be
3.05 m (120") to 15.24 m (600").
*4 Average value. Weight varies for each product.
*5 The operating environment temperature should be between 0 °C (32 °F) and 45 °C (113 °F) if the projector is used at an altitude between 1 400 m
(4 593') and 4 200 m (13 780') above sea level.
*6 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [NORMAL] or [ECO], the light output may be
reduced to protect the projector.
f When using the projector at an altitude lower than 2 700 m (8 858') above sea level: 35 °C (95 °F)
f When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
Note
f The model numbers of accessories and optional accessories are subject to change without prior notice.
262 - ENGLISH
Chapter 7 Appendix — Specifications
100 V - 120 V / 200 V - 240 V ~ (100 V ‑ 120 V / 200 V ‑ 240 V alternating current), 50 Hz/60 Hz
1 100 W (11.0 A / 7.7 A)
0.3 W
4 W
24.4 mm (0.96") (aspect ratio 16:10)
DLP chip x 3, DLP projection system
Optional
Laser diode
16 000 lm
*1*2
90 %
20 000:1 (when [DYNAMIC CONTRAST] is set to [3])
7 standards (NTSC/NTSC4.43/PAL/PAL‑N/PAL‑M/SECAM/PAL60)
1.78 m (70") to 25.40 m (1 000")
16:10
[FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
3.0 m (118‑1/8")
Molded plastic
Black
598 mm (23‑17/32") (excluding protrusions)
307 mm (12‑3/32") (with the feet at shortest position)
270 mm (10‑5/8") (excluding the feet and protrusion)
725 mm (28‑17/32") (excluding the protrusion)
Approx. 49.0 k] (108.0 lbs.)
*4
42 dB
USA and Canada: Class 3R (IEC 60825‑1:2007)
Other countries or regions: Class 1 (IEC/EN 60825‑1:2014)
Risk Group 3 (IEC 62471‑5:2015)
0 °C (32 °F) to 50 °C (122 °F)
*5*6
10 % to 80 % (no condensation)
DC 3 V (AA/R6/LR6 battery x 2)
Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
150 ] (5.3 ozs.) (including batteries)
Width: 47.5 mm (1‑7/8"), Height: 181.5 mm (7‑5/32"), Depth: 27.5 mm (1‑3/32")
When [STANDBY MODE] is set to [ECO]
When [STANDBY MODE] is set to [NORMAL]
When [OPERATING MODE] is set to [NORMAL]
*3