Summary of Contents for SAMES KREMLIN SRV 028 TWIN 60
Page 1
INSTRUCTION MANUAL From February 1st, 2017 SAMES Technologies SAS becomes SAMES KREMLIN SAS A partir du 1/02/17, SAMES Technologies SAS devient SAMES KREMLIN SAS SRV 028 TWIN 60° SPRAY GUN (Ang) Ref. 855 456 Nature of the modification : Added plate CO02.
Page 2
Revision index: E - May 14 , 1998 - 2 - Code : RT 6015...
1. DESCRIPTION 1.1. OVERVIEW (refer to Fig.1) The SRV 028 Twin 60° spray gun comprises the following elements: ∗ two SRV 028-JP guns[A], ∗ a high voltage generator[B], ∗ the linking cable [C] which links the GND 504-B unit (not described in the documentation) to the high voltage generator, ∗...
Page 5
1.2.2. SRV 028-JP GUNS ∗ Max. recommended powder flow..........25 kg/h/gun (i.e. 50 kg/h/2 guns). ∗ Max. recommended output current ........... 30 µA/gun (i.e. 60 µA/2 guns). 1.2.3. DIMENSIONS (refer to Fig.2) ∗ Length of powder spray gun: − without adapter flange ................375 mm, −...
1.3. OPERATING PRINCIPLE OF POWDER SPRAY GUN (refer to Fig.3) The SRV 028-Twin 60° spray gun operates on the "corona" effect principle. An ionizing electrode [A] located at the end of the spray gun and is connected to a high negative potential. Air is ionized by the electrode which is surrounded by the intense electric field.
2. INSTALLATION 2.1. SAFETY RULES IMPORTANT NOTE ...This spray gun is only for use with powder paints. Use of the powder spray gun must comply with the safety precautions specified in this manual (refer to articles R233-140 to R233-150 of the Code of Labour Law on paint booths and powdering). 1.
Page 8
Fig. 4 Revision index: E - May 14 , 1998 - 8 - Code : RT 6015...
3. COMMISSIONING 3.1. PREPARING THE SPRAY GUN (refer to Fig.4) ∗ Fasten the adapter flange [5] onto the bracket used to support the spray gun. ∗ Fasten the socket [1] of the electrical power supply cable onto the fixed flange [2]. Check socket orientation (contact marks in front of plug contacts of plug [3] installed in the mobile flange [4].
4. MAINTENANCE 4.1. PERIODICAL MAINTENANCE AND CHECK-UPS IMPORTANT : All cleaning work should be carried out using compressed air, rags or if necessary brushes. Water should NEVER be used. Spray gun soiling and wear, caused by powder flow, clearly depends on the type of powder used. The guidelines as to cleaning and maintenance frequency provided in the table below can only be taken as an indication of what is required.
BF01-01-B - SRV 028 / UHT 151-RM / BSR 163-P / ABB / SAAB - 855 456 Detail A: fitting the UHT on its support 22 46 See Detail B Revision index: E - May 14 , 1998 - 12 - Code : RT 6015...
BF02-01-B - DISMANTLING AND RE-ASSEMBLY OF THE SRV 028-TWIN 60° SPRAY GUN View A : fitting the UHT on its support Revision index: E - May 14 , 1998 - 14 - Code : RT 6015...
BF02-02-B - DISMANTLING AND RE-ASSEMBLY OF THE SRV 028-TWIN 60° SPRAY GUN 1 - DISMANTLING It is assumed that the spray gun has already been removed. Loosen the screws (25) and (45), and remove the cover (21). Loosen nut QD (26), and remove QD plate (13). Remove screws (24), (47) and remove shell (20).
BF04-B - DISMANTLING AND RE-ASSEMBLY OF THE SRV 028 SPRAY GUN 1 - DISMANTLING It is assumed that the spray gun has already been removed. Loosen the nozzle nut (39). Dismantle the nozzle (33). Loosen the screw (36) and remove the contact washer (38). Remove the O-ring (30).
BF05-A - ECHANGE DU CABLE BASSE TENSION OU DE LA PRISE FEMELLE 1 - DEPOSE Déposer le projecteur SRV 028-TWIN 60°. Dévisser les vis (40) et retirer la prise femelle montée (17). Déconnecter l'autre extrémité du câble basse tension et extraire le tout. Desserrer le presse-étoupe (42).
CO01-01-B - UHT 151-RM - 757 474 Item Article Description Sales code unit 757 474 UHT 151-RM High Voltage Unit X9N VCB 187 Screw C M 5 x 20 nylon X2B VKY 118 Screw C M 4 x 10 J2C RAN 041 Sealing washer 438 704 Cover...