Summary of Contents for SAMES KREMLIN SRV 028-2-TWIN 60
Page 1
INSTRUCTION MANUAL From February 1st, 2017 SAMES Technologies SAS becomes SAMES KREMLIN SAS A partir du 1/02/17, SAMES Technologies SAS devient SAMES KREMLIN SAS SRV 028-2-TWIN 60° - STD US SPRAY GUN (Ang) 855 457 Nature of the modification : Added plate CO2-1.
Page 2
Revision index : C - 1/29/97 - 2 - Code : RT 6076...
1 - DESCRIPTION 1.1 - OVERVIEW (Refer to Fig.1) The SRV 028-2Twin 60° spray gun comprises the following elements: • two SRV 028 guns [A], • a high voltage generator [B], • the linking cable [C] which links the GND 504-B unit (not described in the documentation) to the high voltage generator, •...
Page 6
(Refer to Fig.3) The SRV 028-2-Twin 60° spray gun operates on the "corona" effect principle. An ionizing electrode [A] located at the end of the spray gun and is connected to a high negative potential. Air is ionized by the electrode which is surrounded by the intense electric field.
2 - INSTALLATION 2.1 - SAFETY RULES IMPORTANT NOTE ....This spray gun is only for use with powder paints. Use of the powder spray gun must comply with the safety precautions specified in this manual (refer to articles R233-140 to R233-150 of the Code of Labour Law on paint booths and powdering).
Page 8
Fig. 4. Revision index : C - 1/29/97 - 8 - Code : RT 6076...
[5]. 3.2 - OPERATION AND SETTINGS The SRV 028-2-Twin 60° powder spray gun should be installed 150 to 300 mm from the part to be painted. Voltage adjustments are described in the instructions manual of the GND 504-B control unit (see RT 6017 manual).
4 - MAINTENANCE 4.1 - PERIODICAL MAINTENANCE AND CHECK-UPS IMPORTANT : All cleaning work should be carried out using compressed air, rags or if necessary brushes. Water should NEVER be used. Spray gun soiling and wear, caused by powder flow, clearly depends on the type of powder used. The guidelines as to cleaning and maintenance frequency provided in the table below can only be taken as an indication of what is required.
6. SPARE PARTS SRV 028-2 / UHT 151 RM / BSR 164-P / US View A : fitting the UHT on its support support See view B Revision index : C - 1/29/97 - 12 - - BF1-3 - B - Code : RT 6076...
DISMANTLING AND RE-ASSEMBLY OF THE SRV 028-2-TWIN 60° SPRAY GUN View A : fitting the UHT on its support support Revision index : C - 1/29/97 - 14 - - BF2-3 - B - Code : RT 6076...
DISMANTLING AND RE-ASSEMBLY OF THE SRV 028-2-TWIN 60° SPRAY GUN 1 - DISMANTLING - It is assumed that the spray gun has already been removed. - Loosen the screws (25) and (45), and remove the cover (21). - Loosen nut QD (26), and remove QD plate (13).
DISMANTLING AND RE-ASSEMBLY OF THE SRV 028-2 (US) SPRAY GUN 1 - DISMANTLING - It is assumed that the spray gun has already been removed. - Loosen the nozzle nut (39). - Dismantle the nozzle (33). - Loosen the screw (36) and remove the contact washer (38). - Remove the O-ring (30).
REPLACEMENT OF LOW VOLTAGE CABLE OR SOCKET 1 - DISMANTLING - Remove the SRV 028-2-Twin 60° spray gun. - Loosen the screws (40) and pull the receptacle connector assy (17). - Disconnect the other end of low voltage cable and take off all parts.
INTERNAL CONNECTIONS OF THE SRV 028 SPRAY GUN Vue de l'arrière du projecteur SRV 028 90° powder 90° powder inlet end inlet end piece (28) piece (28) Union (5) Union (5) Air hose Air hose Powder feed pipe Powder feed pipe Powder inlet end Powder inlet end piece (7)
HIGH VOLTAGE UNIT 151-RM - 757 474 Item SAMES Description Sales code unit 757 474 High Voltage Unit 151-RM X9N VCB 181 Screw C M 5 x 10 nylon X2B VKY 118 Screw SCR M 4 x 10 J2C RAN 041 Sealing washer 438 704 Cover...