Ford 1996 Mustang Manual
  1. Manuals
  2. Brands
  3. Ford Manuals
  4. Automobile
  5. 1996 Mustang
  6. Manual

Ford 1996 Mustang Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Ford 1996 Mustang

Summary of Contents for Ford 1996 Mustang

  • Page 3: Table Of Contents

    Table of Contents Introductory Information ... 1 Safety Restraints ... 9 Starting Your Mustang ... 49 Warning Lights and Gauges ... 61 Instrument Panel Controls ... 79 Steering Column Controls ... 91 Features ... 103 Electronic Sound Systems ... 141 Driving Your Mustang ...

  • Page 4: Introductory Information

    Introductory Information Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
  • Page 5 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation.
  • Page 6 Canadian Owners — French Version French Owner Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.
  • Page 7 If you lose your Warranty Information Booklet, you can get a new one free of charge. Contact any Ford or Lincoln-Mercury dealer, or refer to the addresses and phone numbers on the first page of this owner guide.
  • Page 8 The break-in period for new brake linings lasts for 100 miles (160 km) of city driving or 1,000 miles (1,600 km) of highway driving. Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in”...
  • Page 9 Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized its dealers to repair, at no charge to the owner, the surfaces of new vehicles damaged by...
  • Page 10 Cleaning Chrome and Aluminum Parts Wash chrome and aluminum parts with a mild detergent. Do not use steel wool, abrasive cleaners, fuel, or strong detergents. Cleaning Plastic Parts Some of your vehicle’s exterior trim parts are plastic. Clean with a tar and road oil remover if necessary.

  • Page 11: Safety Restraints

    Safety Restraints Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada the law requires their use. Safety belts provide best restraint when: the seatback is upright the occupant is sitting upright (not slouched) the lap belt is snug and low on the hips...
  • Page 12 Failure to follow these precautions could increase the risk and/or severity of injury in a collision. RWARNING Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies...

  • Page 13: Combination Lap And Shoulder Belts

    RWARNING Lock the doors of your vehicle before driving to lessen the risk of the door coming open in a collision. Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, corner hard or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap and shoulder belt...
  • Page 14 Fastening the front seat combination lap and shoulder belt (coupe models) Fastening the front seat combination lap and shoulder belt (convertible models)
  • Page 15 Fastening the rear seat combination lap and shoulder belt coupe and convertible NOTE: Be sure to read and understand Important Safety Belt Information at the beginning of this chapter. Safety Belts for Front Passenger (Coupe Only) and Rear (Coupe and Convertible) Outboard Seating Positions Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of...
  • Page 16 Automatic locking mode In this operating mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled, and does not allow the occupant freedom of movement. This mode provides the following: A tight lap/shoulder belt fit on the occupant.
  • Page 17 NOTE: When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch back to the vehicle sensitive (emergency) locking mode. See the detailed instructions under Safety Seats for Children in this chapter. Front Passenger Lap Belt Retractor (Convertible Only) Your convertible is equipped with a dual locking mode retractor on the lap belt part of the...
  • Page 18 RWARNING Never install a rear-facing child seat or infant carrier in the right front passenger seat. 1. Buckle the lap/shoulder belt. 2. Grasp the lap portion of the belt below the child seat label. Pull upward until all of the belt is extracted and a click is heard.
  • Page 19 RWARNING The lap belts should fit snugly and as low as possible around the hips, not around the waist. RWARNING Failure to follow these precautions could increase the risk and/or severity of injury in a collision. 1) Use the shoulder belt on the outside shoulder only.
  • Page 20 Unfastening the Mustang convertible front outboard lap/shoulder belts 2. While the belt retracts, guide the tongue to its stowed position. If you do not guide the tongue, it may strike you or part of the vehicle. 3. (Coupe only). Place the belt in the belt holder at the top of the seatback.
  • Page 21 Belt holder location — coupe only 4. (Convertible only). Place the shoulder belt in the belt holder at the top of the seatback and place the lap belt in the belt guide at the side of the seat cushion. The retracted belt should be stored on this holder and in the belt guide when not in use, except when a passenger is entering or leaving the rear seat...
  • Page 22 Belt holder location — convertible only RWARNING The shoulder belt must always be in the belt holder when the belt is in use. Safety Belt Extension Assembly For some people, the safety belt may be too short even when it is fully extended. You can add about eight inches (20 cm) to the belt length with a safety belt extension assembly (part number 611C22).

  • Page 23: Safety Belt Maintenance

    (slide bar) (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
  • Page 24 Air Bag Supplemental Restraint System (SRS) The driver and right front passenger air bags are Supplemental Restraint Systems (SRS), provided at these seating positions in addition to the lap/shoulder belt, and are designed to supplement the protection provided to properly belted occupants in moderate to severe frontal collisions.
  • Page 25 The Importance of Being Properly Seated In a collision, the air bag must inflate extremely fast to help provide additional protection for you. In order to do this, the air bag must inflate with considerable force. If you are not seated in a normal riding position with your back against the seatback, the air bag may not protect you properly and could possibly hurt you as it...
  • Page 26 move the seat to the most rearward position if possible and use the safety belts. Children weighing less than 40 lbs. (18 kg) always should use child or infant seats. RWARNING When using forward-facing child seats move the passenger seat as far back from the instrument panel as possible.
  • Page 27 For further information about the proper mounting of equipment in the front seat of this vehicle, please refer to Ford’s brochure entitled Some Important Information About Air Bag Supplemental Restraint System which can be obtained by calling Helm Inc. at 1-800-782-4356.
  • Page 28 If a collision occurs, the sensors sense the severity of the impact and activates the air bags if necessary. The air bag system is designed to deploy in frontal and front-angled collisions more severe than hitting a parked vehicle (of similar size and weight) head-on at about 28 mph (45 km/h).
  • Page 29 Inflated right front passenger side air bag RWARNING If the air bag is inflated, THE AIR BAG WILL NOT FUNCTION AGAIN AND MUST BE REPLACED IMMEDIATELY. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.

  • Page 30: Safety Restraints For Children

    If any of these things happen, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the air bag Supplemental Restraint System may not function properly in the event of a collision.
  • Page 31 RWARNING Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. RWARNING Passengers should not be allowed to ride in the cargo area. Persons not riding in a seat with a fastened seat belt are much more likely to suffer serious injury in a collision.
  • Page 32 Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
  • Page 33 RWARNING REAR-FACING INFANT SEATS SHOULD NEVER BE USED IN THE FRONT SEAT. REAR-FACING INFANT SEATS MUST ALWAYS BE PLACED IN THE REAR SEAT. Failure to follow these instructions could result in serious injury. All child restraint systems are designed to be secured in vehicle seats by lap belts or by the lap portion of a lap-shoulder belt.
  • Page 34 Installing Safety Seats in the Front Seat — Convertible Your Mustang Convertible is equipped with a dual locking mode retractor on the lap belt portion of the lap/shoulder belt at the front passenger seat. The automatic locking mode must be used when installing a child seat in the front passenger seat.
  • Page 35 3. Following the child seat manufacturer’s instructions, route the lap/shoulder belt through the child seat or infant carrier and insert the belt tongue into the buckle until you hear and feel the latch engage, Figure 2. Routing the lap/shoulder belt...
  • Page 36 4. Grasp the lap portion of the belt below the child seat label. Pull upward until all of the belt is extracted and a click is heard. At this time, the lap belt retractor is in the automatic locking mode (child seat restraint mode), Figure 3.
  • Page 37 5. Allow the belt to retract. A clicking sound will be heard as the belt retracts. This indicates the retractor is in the automatic locking mode, Figure 4. Allowing belt to retract...
  • Page 38 6. Push down on the child seat while you pull down on the belt to remove any slack in the belt, Figure 5. Removing slack from the belt...
  • Page 39 7. Before placing the child in the child seat or infant carrier, forcibly tilt the seat from side to side, and also tug it forward to make sure that the seat is securely held in place, Figure 6. Checking that the seat is secure...
  • Page 40 8. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor, if you cannot, the belt is in the automatic locking mode, Figure 7. Checking the retractor 9. Check to make sure that the child seat or infant carrier is properly secured prior to each use.
  • Page 41 Installing Safety Seats in the Front Seat (Coupe only) and Rear Seating Positions (Coupe and Convertible) For seating positions equipped with a dual locking mode retractor, use the following procedure. If you choose to install a child safety seat or infant carrier in the front seating positions, move vehicle seat as far back as possible.
  • Page 42 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. See Figure 2. Be sure that the belt webbing is not twisted. Routing the lap/shoulder belt 4.
  • Page 43 Buckling the belt 5. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child seat restraint mode). See Figure 4.
  • Page 44 Setting the retractor to automatic locking mode 6. Allow the belt to retract. Pull up on the shoulder webbing. A clicking sound will be heard as the belt retracts. This indicates the retractor is in the automatic locking mode. Push down on the child seat while you pull up on the belt to remove any slack in the belt.
  • Page 45 Allowing shoulder belt to retract Removing slack from belt...
  • Page 46 7. Before placing the child in the child seat, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place. See Figure 7. Checking that the seat is secure...
  • Page 47 8. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor. If you cannot, the belt is in the automatic locking mode. See Figure 8. Checking the retractor 9. Check to make sure that the child seat is properly secured prior to each use.
  • Page 48 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and...
  • Page 49 belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion.

  • Page 50: Starting Your Mustang

    Starting Your Mustang Ignition Understanding the Positions of the Ignition The positions of the key in the ignition ACCESSORY allows some of your vehicle’s electrical accessories such as the radio and the windshield wipers to operate while the engine is not running.
  • Page 51 ON allows you to test your vehicle’s warning lights (except the brake system warning light) to make sure they work before you start the engine. The key returns to the ON position once the engine is started and remains in this position while the engine runs.
  • Page 52 NOTE: If your vehicle has an automatic transmission, the gearshift lever must be in the P (Park) position to remove the key from the ignition. If the key is stuck in the LOCK position, move the steering wheel left or right until the key turns freely.

  • Page 53: Warning Lights And Gauges

    Starting Your Vehicle Preparing to Start Your Vehicle RWARNING Do not start your vehicle in a closed garage or other enclosed area. Never sit in a stopped vehicle for more than a short period of time with the engine running. Exhaust fumes are toxic.
  • Page 54 Starting Your Engine To start your engine: 1. Follow the steps under Preparing to Start Your Vehicle at the beginning of this section. 2. Turn the ignition key to the ON position. 3. DO NOT depress the accelerator pedal when starting your engine.
  • Page 55 Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. After you start the engine, let it idle for a few seconds. Keep your foot on the brake pedal and put the gearshift lever in gear.
  • Page 56 To turn the heater on, simply plug it into a grounded 110-volt outlet. Ford recommends that you use a 110-volt circuit that is protected by a ground fault circuit interrupter.
  • Page 57 For best results, plug the heater in at least three hours before you start your vehicle. Using the heater for longer than three hours will not damage the engine, so you can plug it in at night to start your vehicle the following morning.
  • Page 58 If the engine is idling while you are stopped in an open area for long periods of time, open the windows at least one inch (2.5 cm). Also, the heating or air conditioning system should be set to any function except MAX A/C or AUTO. If you use the heater, set the fan speed on MEDIUM or HIGH with the function control knob at any desired position.
  • Page 59 The fuel pump shut-off switch RWARNING If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service.
  • Page 60 5. Check under the vehicle again for leaking fuel. If you see or smell fuel, do not start your vehicle again. If you do not see or smell fuel, you can try to start your vehicle again. 6. Check all vehicle warning lights before driving the vehicle.

  • Page 61: Warning Lights And Gauges

    Warning Lights and Gauges The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles.
  • Page 64 The Cluster The following warning lights and gauges are on the cluster. All of the warning lights and gauges alert you to possible problems with your vehicle. Some of the lights listed are optional. The following sections detail what each of these indicators means.
  • Page 65 Anti-Lock Brake System Light (If equipped) This warning light will go on each time you start your vehicle. If it remains on for longer than five seconds, you should shut off your engine and restart. If the anti-lock brake light stays on, this indicates that the anti-lock feature is disabled and should receive immediate attention by a qualified service technician.
  • Page 66 1. Park your car on level ground, and turn off the engine and allow a few minutes for the engine oil to drain back into the oil pan. 2. Use the dipstick to check the oil. If the level is low, add oil, but do not overfill. See Engine Oil Recommendations in the Index.
  • Page 67 If there is a problem with the system, two things may happen: the readiness light will either flash or stay lit up, or you will hear a beeping sound. If either of these things happen, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately.
  • Page 68 Low Coolant Warning Light (4.6L Engine Only) This light tells you that the coolant is low inside the coolant recovery bottle and that you should add more coolant. This light comes on for a few seconds when your ignition key is turned to start, but should turn off when the engine starts.
  • Page 69 If the light stays on or comes on when the engine is running, have the electrical system checked as soon as possible. Overdrive Off Indicator (Automatic Only) This light tells you that the Transmission Control Switch (O/D) to the right of the gearshift lever has been pushed.
  • Page 70 High Beam Light This light comes on when the headlamps are turned to high beam or when you flash the lights. Check Engine Warning Light The Powertrain On-Board Diagnostic II (OBD II) system consists of the hardware and software necessary to monitor the operation of the powertrain.
  • Page 71 The light comes on briefly when you turn the ignition key to ON, but it should turn off when the engine starts. If the light does not come on when you turn the ignition to ON or if it comes on and stays on when you are driving, have your vehicle serviced as soon as possible.
  • Page 72 Under certain conditions, the Check Engine Warning Light may come on if the fuel cap is not properly installed. If the Check Engine Warning Light comes on and you suspect that the fuel cap is not properly installed, pull off the road as soon as it is safely possible and turn off the engine.
  • Page 73 Fuel Gauge The fuel gauge The fuel gauge displays approximately how much fuel is in the fuel tank only when the ignition switch is ON. For proper fuel gauge indication after adding fuel, turn the ignition switch OFF while refueling the vehicle. The fuel gauge indicator may vary slightly when the vehicle is in motion.
  • Page 74 conditions, and under certain driving conditions such as, heavy stop and go traffic, or driving up hills in hot weather, for the pointer to indicate at the top of the NORMAL band. If, under any circumstances, the pointer moves above the NORMAL band, the engine is overheating and continued operation may cause engine damage.
  • Page 75 Speedometer The speedometer The speedometer tells you how many miles (kilometers) per hour your vehicle is moving. Odometer The odometer tells you the total number of miles (kilometers) your vehicle has been driven. Trip Odometer If you want to track your mileage up to 999.9 miles (kilometers), use the trip odometer.
  • Page 76 Tachometer The tachometer The tachometer displays the approximate engine revolutions per minute (rpm), or how fast the engine is running. The white zone shows the highest number of engine revolutions per minute (rpm) at which you should drive your car. Driving with the pointer in the red zone may cause engine damage.
  • Page 77 Battery voltage gauge Engine Oil Pressure Gauge This gauge indicates the engine oil pressure, not the oil level. However, if your engine’s oil level is low, it could affect the oil pressure. With the engine running, the pointer should move into the NORMAL band.
  • Page 78 If you lose engine oil pressure: 1. Pull off the road as soon as safely possible. 2. Shut off the engine immediately or severe engine damage could result. 3. Check the engine’s oil level, following the instructions on checking and adding engine oil, see the Engine Oil in the Index.
  • Page 80 The main controls for the climate control system, clock, and radio are on the instrument panel. NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection.
  • Page 81 The knobs that control the optional heating and air conditioning system The heating system in the optional heating and air conditioning system operates the same as the heater only system. See The Heater Only System. To cool your vehicle quickly in warm weather, turn the SELECT knob to MAX A/C, turn the TEMP knob all the way to the end of the blue range (full left) and turn the FAN knob to HI.
  • Page 82 Under normal conditions, the SELECT knob should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. The Heater Only System You can heat the inside of your vehicle, defrost the windshield, or use the vents by adjusting the three knobs in the center of the instrument panel:...

  • Page 83: Rear Window Defroster

    To heat the inside of your vehicle and defrost the windshield and side windows at the same time, turn the SELECT knob to MIX, turn the TEMP knob into the red range, as required, and turn the FAN knob to the desired speed between LO and HI.

  • Page 84: The Interior And Exterior Lights

    Clear away any snow that is on the rear window before using the defroster. With the engine running, push the defrost button. After approximately 10 minutes, the defroster will turn off. If the window is still not clear, turn the defroster on again. The defroster will turn off when the ignition key is turned to the OFF position.
  • Page 85 RWARNING The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk. Failure to do so may result in a collision. Turning On the Exterior Lights To turn on the headlamps, parking lamps, side markers, and tail lamps, use the control knob that is to the left of the steering wheel.

  • Page 86: Steering Column Controls

    When you turn on the headlamps, the parking lamps, tail lamps, and side markers automatically turn on. But you can turn on the parking lamps, tail lamps, and side markers without turning on the headlamps. For more information about how the high beams work, refer to the Steering Column Controls chapter.
  • Page 87 Lighting Up the Interior and Instrument Panel With the headlamp knob in the parking lamps or headlamps position, you can brighten or dim the lights on the instrument panel. To do this, rotate the headlamp knob clockwise (to dim the lights) or counterclockwise (to brighten the lights).
  • Page 88 Turning on the Map and Reading Lamps Your vehicle has two map lamps for the passenger and the driver. To turn on the map lamps, push the switch next to each lamp. Map lamp (convertible only) Front seat map and dome lamps (coupe only) The dual beam map lamps are located on each side of the dome lamp.
  • Page 89 Cleaning the Instrument Panel Lens Clean the instrument panel lens with a soft cloth and a glass cleaner, such as Ford Ultra-Clear Spray Glass Cleaner, or equivalent. Do not use paper towel or any abrasive cleaner to clean the...

  • Page 90: Steering Column Controls

    Steering Column Controls The controls on the steering column and wheel are designed to give you easy access to the controls while you are driving. The Turn Signal Lever You can use the turn signal lever on the left side of the steering column to: operate the turn signals turn the high beams on/off...

  • Page 91: Windshield Wipers And Washer

    If the turn signal stays on after you turn, move the lever back to the center (off) position. For lane changes, move the lever far enough to signal but not to latch. The lever will return to the off position when you release it. High Beams To turn on the high beams, turn the headlamp control knob to the headlamp ON position and...
  • Page 92 HI, LO, or the interval setting selected. If the washer does not work, check the washer fluid level and fill it if it is low. See the Servicing Your Mustang chapter. If there is enough fluid, consult your nearest Ford or Lincoln-Mercury dealer.
  • Page 93 Do not try to clean the windshield when the washer fluid container is empty or activate the washers at any time for more than 15 seconds continuously. This could damage the washer pump system. RWARNING In freezing weather, the washer solution may freeze on the windshield and obscure your vision.
  • Page 94 The control switch for the hazard flashers Horn To sound the horn, push the center pad area of the steering wheel. The horn on the steering wheel...

  • Page 95: Tilt Steering

    Tilt Steering RWARNING Never adjust the steering wheel when the vehicle is moving. The lever to tilt the steering wheel To change the position of the steering wheel, pull the release lever on the column toward you. Tip the steering wheel to the desired position. Release the lever to lock the steering wheel in place.
  • Page 96 Speed Control (If equipped) If your vehicle has speed control, you can automatically maintain a constant speed at or above 30 mph (50 km/h). Use of radio transmitting equipment that is not Federal Communications Commission (FCC) or in Canada the Canadian Radio and Telecommunications Commission (CRTC) approved may cause the speed control to malfunction.
  • Page 97 temporary resumption of manual speed control while ascending steep grades in order to maintain the selected speed. The speed control switches on the steering wheel To set the speed control: 1. Press and release the ON switch. 2. Accelerate to the desired speed above 30 mph (50 km/h) using the accelerator pedal.
  • Page 98 If you drive up or down a steep hill, your vehicle may momentarily slow down or speed up, even though the speed control is on. This is normal. NOTE: If your speed increases above your set speed while driving in D (Drive) on a downhill grade, you may want to depress the Transmission Control Switch located on the shift lever to...
  • Page 99 Accelerating With the Speed Control Operating You can use the accelerator pedal to speed up momentarily. When you take your foot off the accelerator, the vehicle will return to the set speed. Resetting the Speed Control To reset the speed control to a lower speed, use one of the following procedures: COAST —...
  • Page 100 Depress the accelerator pedal. When the vehicle attains the desired speed, press the SET ACCEL switch and release it immediately. TAP-UP — Press and then quickly release the SET ACCEL switch. Each time you “tap” the switch, the set speed will increase by one (1) mph (1.6 km/h).

  • Page 101: Features

    Features Your vehicle has a variety of features designed for your comfort, convenience and safety. Read this chapter to find out about standard and optional features. Doors Anti-theft front door lock knobs Anti-theft lock knobs are designed to prevent unlocking the door by pulling up on the lock knob.
  • Page 102 The power locks on the driver’s door Anti-Theft Alarm System (If equipped) When armed, this system helps protect your vehicle against break-ins or theft. When an unauthorized entry occurs, the system triggers and will: flash the headlamps, parking lamps, and alarm indicator lamp honk the horn disable the starting circuit to prevent the...
  • Page 103 NOTE: The factory installed Remote Entry System has a PANIC feature that also chirps the vehicle horn and flashes the interior/exterior lamps when the PANIC button on the remote entry transmitter is pushed. The PANIC alarm and the Anti-Theft alarm are two separate features.
  • Page 104 4. Close all doors. The alarm indicator light will then remain on steadily for approximately 30 seconds and then go out. When the light goes out, the system is armed. NOTE: Be sure to close all doors completely. If not, the alarm indicator light will remain on.
  • Page 105 Triggering the alarm system The armed system will be triggered if: any door is opened without disarming the system first (see previous paragraphs) the trunk lock cylinder is removed NOTE: You can open the trunk with your key without setting off the alarm. the hood is opened (except on GT/Cobra vehicles) the ignition key lock cylinder is forcibly...
  • Page 106 Additional spare keys, maximum of 14, can be purchased either through your dealership or selected retailers. Be sure to purchase only coded keys with a Ford or Mercury logo on it to ensure proper functionality. If both supplied keys are lost or stolen, the vehicle must be brought to the dealership for re-initialization.
  • Page 107 Theft Indicator The indicator provides system proveout and operating status. The system activates the indicator when the ignition switch is placed in the ON or START position. This indicator helps to determine possible fault conditions and/or normal operating proveout. The system will illuminate the indicator for two (2) seconds then go out to acknowledge normal operating conditions.

  • Page 108: Remote Entry System

    Remote Entry System (If equipped) If your vehicle has the remote entry system, you can lock and unlock the vehicle doors and open the trunk without using a key. The remote also has a personal alarm feature. The buttons for the system are located on the hand held transmitter(s) that came with your vehicle.
  • Page 109 Locking the doors To lock all the doors, press the LOCK button. If you would like a signal that the doors are being locked, press the LOCK button again within five seconds. The doors will lock again, the horn will beep and the low beam headlamps and tail lamps will flash.
  • Page 110 (included) that should last for several years of normal use. If you notice a significant decrease in operating range, the batteries should be replaced. Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer.
  • Page 111 NOTE: The operating range of the remote entry system can also be affected by weather conditions (such as very cold temperatures) or structures around the vehicle (buildings, other vehicles, radio and TV towers, etc.). Typical operating range will allow you to be up to 33 feet (10 meters) away from your vehicle.
  • Page 112 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
  • Page 113 The master controls on the driver’s door — convertible shown To lock out all window switches except the master controls, press the window lock switch once. To restore control to the individual windows, press the switch again. There is also an Express Down feature on the driver’s power window.
  • Page 114 Seats Head Restraints If you use them properly, head restraints will help protect your head and neck in a collision. A head restraint helps protect you best if you position it behind your head and not behind your neck. Standard head restraints You can adjust the head restraints for your comfort and protection.
  • Page 115 The four-way head restraint Adjusting Manual Seats In the front seats, you can move the whole seat forward or backward or tilt the back of the seat forward or backward. To move the seats forward or backward: 1. Find the adjustment lever at the lower left corner of the front seat.
  • Page 116 The front seat adjustment lever To recline the front manual seats: 1. On the side of the seat, find the handle for the recliner. 2. Lift the handle up and hold it in place. 3. Lean against the back of the seat and adjust it to the position you want.
  • Page 117 Seatback Recline Front seatback release levers It is necessary to use the seatback release when folding the back of the front seat forward for rear seat passenger entry or exit. This release handle is located on the lower outboard back of the seat.
  • Page 118 Using the Power Seat (If equipped) If your vehicle has a driver side power seat, you can adjust it in several directions. Using the seat adjustment switch, located on the front outboard corner of the driver’s seat, you can raise or lower the whole front seat and move the seat forward or backward.
  • Page 119 Sport Seat Controls (GT models) Using the Power Lumbar Supports You can inflate a lumbar support pad in the seat back. To inflate the lumbar pad, push the (+) side of the rocker switch. To deflate push the (-) side of the switch. Using the Lateral Support Handwheel (driver only) To increase lateral support rotate the handwheel...
  • Page 120 Rear Seat Entry Coupe models Entering the rear seat (coupe) The rotating boot on the lap belt is designed to allow rear seat entry/exit. To enter the rear seat: 1. Remove seat belt from seat belt guide on top of front seat. 2.
  • Page 121 Convertible models Entering the rear seat (convertible) To enter the rear seat: 1. Remove the shoulder belt from the seat belt guide on top of front seat. 2. Remove the lap belt from the seat belt guide on side of seat. 3.
  • Page 122 Folding Rear Seat (Coupe only) To fold down the rear seats, gently pull on the release straps. NOTE: It may be necessary to apply slight hand pressure to top of seatback while pulling on release strap. Rear seat release straps To raise the rear seatback: 1.
  • Page 123 Cleaning the Seats Leather and vinyl For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a leather and vinyl cleaner or a mild soap. Fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner.
  • Page 124 Rearview Mirror and Lamp Assembly (convertible only) This rearview mirror contains two lamps which function as courtesy lamps when the doors are open. These lamps also function as map lamps when the doors are closed and the rocker switch is activated. The rearview mirror with lamps...
  • Page 125 Adjusting the Side View Mirrors The switch for controlling the dual electric remote control mirrors is located on the driver’s door. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. The mirror controls on the driver’s door To adjust the side mirrors: 1.

  • Page 126: Sun Visors

    The Right Side Convex Mirror The side view mirror on the right is a convex mirror. This mirror gives you a wider view of the lanes on your right and behind you. RWARNING The side view mirror on the right makes objects appear smaller and farther away than they actually are.
  • Page 127 Console Your vehicle has a full console. The full console has the features shown in the illustration below. The features on the full console...
  • Page 128 Power Point Electrical Outlet The power point outlet is located on the console to the right of the shift lever. This outlet should be used in place of the cigarette lighter for optional electrical accessories. NOTE: Do not plug optional electrical accessories into the cigarette lighter.

  • Page 129: Storage Compartments

    Storage Compartments Your vehicle may have several small storage compartments: a glove compartment that locks. if equipped with power windows, two map pockets on the panels of the front doors. center console storage compartment under the arm rest that may be used for storage of CD’s or cassettes.
  • Page 130 Using the Remote Control for the Trunk (If equipped) You can use the remote control inside your glove compartment to unlock and open the trunk. If equipped, you can also use your remote entry system to open the trunk. The remote control for the trunk Convertible (If equipped) NOTE: Do not store articles behind rear seat.
  • Page 131 2. Check the convertible top stowage compartment behind the rear seat to be sure it is empty and ready to receive the top. 3. Unclamp the top from the windshield header at both the right and left sides by pulling each clamp rearward until the hook in the windshield header is free.
  • Page 132 Convertible top switch Installation of the Boot To install the boot: 1. Insert boot tongue into groove located on rear seat.
  • Page 133 2. Push boot forward until rear attachment engages under molding. 3. Push forward flap of boot until both clips engage under trim panel edge. Repeat on other side of car.
  • Page 134 4. Tuck side attachments under molding. Repeat on other side of car. 5. Push and pull front of boot to ensure tongue is engaged into groove.
  • Page 135 6. Removal Raising the Convertible Top NOTE: CONVERTIBLE TOP WILL NOT OPERATE UNLESS PARKING BRAKE IS ENGAGED. Do not raise the top while the vehicle is moving because the top may be severely damaged. To raise the convertible top: 1. Bring the vehicle to a complete stop. Engage the parking brake.
  • Page 136 9. Raise the front and rear side windows. Convertible Top and Padded Molding Care To avoid damage to the vinyl top and moldings, use only an approved Ford cleaner, or equivalent. Do not use stiff bristle brushes or abrasive material or cleaners.
  • Page 137 Positive Location Floor Mat When installing or removing the driver’s side floor mat you must attach/detach the positive location grommet from the hook on the floor. The hook is just forward of the left hand track of the driver’s seat. The positive location floor mat hook...
  • Page 139 Electronic Stereo Cassette Radio Using the Controls on Your New Radio How to turn the radio on and adjust the volume Press the “POWER” button to turn the radio on. Press it again to turn it off. Press the right (+) side of the “VOLUME” button to increase the volume.
  • Page 140 Using the “AMS” function to manually tune your radio You can change the frequency up or down one increment at a time by first pressing the “AMS” button, (display shows “TUNE”) then pressing and releasing either the right a or left b side of the “SEEK”...
  • Page 141 Setting the Station Memory Preset buttons Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FM1 and 6 in FM2). Follow the easy steps below to set these buttons to the desired frequencies: 1.
  • Page 142 Speaker features and operation Adjusting speaker balance Balance control allows you to adjust the sound distribution between the right and left speakers. Push the “AUDIO” button repeatedly until the display reads “BAL.” Push the right (+) side of the “VOLUME” button to shift the sound to the right speakers, and push the left ( ) side to shift the sound to the left speakers.
  • Page 143 How to locate a desired track on the tape NOTE: The tape track or side number indicated in the display does not necessarily correspond to the tape track or side number on the cassette label. It is used only to indicate when the tape mechanism reverses tracks.
  • Page 144 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
  • Page 146 Ford Mini Disc Player The Ford Mini Disc Player operates when the Audio System is on and a disc is inserted (label side up). (Be sure to read and follow all of the care and cleaning instructions under How To Take Care of Your Mini Disc Player and Discs in this section.)
  • Page 147 NOTE: The Mini Disc player has heat protection circuitry to protect the laser diode. If the temperature of the player reaches 167˚F (75˚C), the heat detection circuit will shut off the player and “HOT” will appear in the display. When the temperature is within normal operating range, the “HOT”...
  • Page 148 Using the “SCROLL” feature The scroll feature allows the display to scroll through titles that are larger than 12 characters. Press the “SCROLL” button to activate the scroll feature. Using the “AMS” feature Pressing the right ( e ) side of the “AMS” button advances the disc forward one track at a time.
  • Page 149 How To Take Care of and Clean Your Mini Disc Player and Discs To ensure the continued performance, of your Ford Mini Disc Player carefully read the following precautions. Always handle the disc by its edge. Never touch the playing surface.
  • Page 150 Mini Disc format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Mini Disc Player. If play does not begin after the CD button is pushed: The radio is not on.
  • Page 152 Ford Compact Disc Player The Ford Compact Disc Player operates when the Audio System is on and a disc is inserted (label side up). Handle the disc by its edge only. (Be sure to read and follow all of the care...
  • Page 153 NOTE: Once a disc is inserted, the disc opening is secured to prevent the accidental insertion of a second disc. NOTE: The CD player has heat protection circuitry to protect the laser diode. If the temperature of the player reaches 167˚F (75˚C), the heat detection circuit will shut off the player and “HOT”...
  • Page 154 How to fast forward or reverse your CD player To quickly search for a particular point in a selection, press the right ( e ) side of the “REV/FF” button (to fast forward) or the left ( f ) side (to rewind). While either side of the button is pressed, the disc goes forward or backward at two different speeds depending on how long the button is held down.
  • Page 155 Special Features of Your CD Player Compression The compression feature will bring soft and loud passages closer together for a more consistent listening level. To turn the compression on, press the “COMPRESS” button. When on, the compression indicator (“COMP”) will appear in the display.
  • Page 156 How To Take Care of and Clean Your CD Player and Discs To ensure the continued performance of your Ford Compact Disc Player, carefully read the following precautions: Always handle the disc by its edge. Never touch the playing surface.
  • Page 157 CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Player.
  • Page 158 If play does not begin after the CD button is pushed: The radio is not on. The unit is in the stop mode. Moisture may have condensed on the lenses within the unit. If this occurs, remove the disc and wait approximately an hour until the moisture evaporates.
  • Page 160 Mach 460 Sound System Using the Controls on Your New Radio How to turn the radio on and off Press the “POWER” button to turn the radio on. Press it again to turn it off. How to adjust the volume Press the +/ side of the “VOLUME”...
  • Page 161 Using the “TUNE” function You can change the frequency up or down one increment at a time (FM changes in increments of 200 kHz; AM changes in increments of 10 kHz) by first pressing the “SCAN/TUNE” button twice (display shows “TUNE”), then —...
  • Page 162 Using the “SCAN” function Pressing the “SCAN/TUNE” button once enters the scan mode (display will indicate “SCN”). Pushing the right ( a ) side of the “SEEK” button will begin the scan mode up the frequency band, stopping on each listenable station for approximately a five-second sampling.
  • Page 163 Using the Automatic Memory Load feature If no stations are in memory preset, you can activate the Auto Memory Load feature by pressing and holding the “AUTO PRESET” button for approximately three seconds. Auto Memory Load sets all memory buttons in AM, FM1 and FM2 sequentially by seeking out the first six strong stations for the respective band and storing them in memory...
  • Page 164 After all stations have been filled, the radio will begin playing the station stored on memory button 1. To deactivate the Auto Memory Store mode and return to the manually-set memory button stations (or those stations set using Auto Memory Load), simply push the “AUTO PRESET”...
  • Page 165 Adjusting speaker fader Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the right (+) side of the “VOLUME” button to shift the sound to the front speakers, and push the left ( ) side to shift the sound to the rear speakers.
  • Page 166 How to locate a desired track on the tape There are four ways to quickly locate a desired selection on the tape. You can use the fast forward, rewind, “SEEK” or “SCAN” function. Following are brief descriptions of each. Fast forwarding the tape To fast forward the tape, press the “FF”...
  • Page 167 Using the “SCAN” function with your cassette tape player Press the “SCAN/TUNE” button to enter the scan mode (display indicates “SCN”). Pushing the right ( a ) side of the “SEEK” button will begin the forward scan mode on the tape currently playing, stopping on each tape selection for approximately an eight-second sampling.
  • Page 168 How to store the tape Press the “AM/FM” button to stop the tape player and resume radio play. The cassette will be stored in the tape player and the X symbol in the display will be lit until you push the “PLAY PROG”...
  • Page 169 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
  • Page 170 Common Radio Reception Conditions Several conditions prevent FM reception from being completely clear and noise-free, such as the following: 1. Distance/Strength The strength of the FM signal is directly related to the distance the signal must travel. The listenable range of an average FM signal is approximately 25 miles (40 kilometers).
  • Page 171 To minimize these conditions, a stereo/mono blend circuit has been incorporated into this system. This feature automatically switches a weak stereo signal to a clearer monaural signal, which improves the quality of reception. Several sources of static are normal conditions on AM frequencies.
  • Page 172 Ask your dealer for a copy of this limited warranty. Service At Ford Electronics, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
  • Page 173 Driving Your Mustang Procedures for driving your vehicle will vary depending on which type of transmission your vehicle has. an automatic overdrive transmission with transmission control switch a manual transmission Driving with an Automatic Overdrive Transmission The gearshift lever is floor mounted. Putting Your Vehicle in Gear RWARNING Hold the brake pedal down while you...
  • Page 174 3. Move the gearshift lever out of P (Park). Your vehicle is equipped with a Brake Shift Interlock safety feature. This feature prevents the gearshift from being moved from the P (Park) position until the brake pedal is depressed. This feature is active when the ignition is in the ON position.
  • Page 175 The positions of the console-mounted gearshift Once the gearshift is secure in the desired position, release the brake pedal and use the accelerator as necessary. R (Reverse) With the gearshift in the R (Reverse) position, the vehicle will move backward. You should always come to a complete stop before shifting into or out of R (Reverse).
  • Page 176 Driving Your vehicle’s gearshift is console-mounted on the floor. The Transmission Control Switch (TCS) is located on the console to the right of the gearshift handle and is marked “O/D”. The Transmission Control Indicator Light is located on the instrument panel. You can put the gearshift lever in any of the several positions.
  • Page 177 However, Overdrive also shifts into a fourth gear —an overdrive gear — when your vehicle cruises at an appropriate consistent speed for any length of time. This fourth gear will increase your fuel economy when you travel at cruising speeds. When to use D (Overdrive) —...

  • Page 178: Driving With A Manual Transmission

    RWARNING Always set the parking brake fully and make sure the gearshift is securely latched in P (Park). RWARNING Never leave your vehicle unattended while it is running. You can tell a console-mounted gearshift is securely latched in P (Park) if the lever is adjacent to the P (Park) and you cannot move it without pushing in the thumb button.
  • Page 179 Shifting the Gears The gearshift can be in one of seven possible positions, as shown below. The positions of the floor-mounted gearshift Always push the clutch pedal all the way in when you shift. You should upshift according to the speeds given in the chart in this section. Backing up To shift into R (Reverse): 1.
  • Page 180 Upshifting Most of the time, you should upshift at the following speeds: Shift Speeds for 3.8L Engine Models Shift Speeds for 4.6L Engine Models * In these gears, you may sometimes shift at lower speeds than those we suggest to improve fuel economy.
  • Page 181 Downshifting When you slow down or climb a steep hill, always downshift before the engine starts to lose power. Downshifting reduces the chance of stalling and gives your vehicle better acceleration to increase speed again. When you drive down steep hills, downshifting helps you keep a safe speed and helps prevent unnecessary wear on the brakes.

  • Page 182: Steering Your Vehicle

    Extended use of other than matching size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver. RWARNING To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire.
  • Page 183 wheels to continue to roll while you are slowing down, which lets you steer properly. On vehicles without anti-lock brakes, extreme braking can make the wheels lock and slide, possibly decreasing your control of the steering. If you lock the wheels, release the brake pedal and repeat the “squeeze”...
  • Page 184 Ford Motor Company has not found any detrimental effects of popular mobile radio transmitting equipment installed on vehicles with the anti-lock brake system, if the equipment is installed according to the manufacturer’s instructions. However, if mobile radio transmitting equipment is installed in your...
  • Page 185 RWARNING When parking, do not use the gearshift in place of the parking brake. Turn the key to LOCK whenever you leave your vehicle. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
  • Page 186 Driving Under Special Conditions Tips for Safe Driving As with any new vehicle, yours may drive and handle differently from your previous vehicle. Use care until you become accustomed to its various features and driving characteristics. Operate your vehicle within reasonable limits. Sudden acceleration, deceleration, turning, or combinations of these maneuvers can cause a vehicle to behave differently than anticipated.
  • Page 187 RWARNING If your vehicle has speed control, do not use it on slippery roads. You could lose control of your vehicle and could injure someone. If your vehicle gets stuck (for example, in mud or snow), you may try to “rock” it out of the spot.
  • Page 188 Driving With a Heavy Load There are limits to the amount of weight your vehicle can carry or tow. The total weight of your vehicle, plus the weight of the passengers and cargo, should never be more than the Gross Vehicle Weight Rating (GVWR).
  • Page 189 luggage and any other items that you put in your vehicle the tongue load of the loaded trailer the weight of any equipment that has been added to your vehicle since it was delivered to your dealer If you do not know the actual weights of these items, use the following procedure to figure the weight of a load: 1.

  • Page 190: Trailer Towing

    Trailer Towing Your vehicle does not come from the factory fully equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers. Because towing a trailer puts extra strain on your vehicle, you must follow certain precautions for your safety and the good of your...
  • Page 191 If you are not certain that you are using the right equipment in the proper manner, see your Ford or Lincoln-Mercury dealer. Do not use hitches that clamp onto your vehicle’s bumper. The bumper is not designed to bear the load.
  • Page 192 Connecting the safety chains Always attach the trailer’s safety chains to your vehicle. They help protect your trailer if the hitch breaks. To connect the trailer’s safety chains: 1. Cross the chains under the trailer tongue and attach them to your vehicle’s frame or hook retainers.
  • Page 193 To get the proper equipment for hooking up your trailer’s lights, see your local trailer dealer and your Ford dealer. Be sure to follow their instructions carefully. If your vehicle is equipped with the optional trailer tow package, the proper lamp wiring and equipment has been installed at the factory.
  • Page 194 If your vehicle has a manual transmission and you are towing a trailer, you should select gear positions which will avoid jerking or excessive engine speed. If you need to drive excessively in 1 (First) or 2 (Second), it may indicate that the trailer is too big or heavily loaded for your vehicle’s drivetrain.

  • Page 195: Roadside Emergencies

    Roadside Emergencies Jump-Starting Your Vehicle Your vehicle’s battery may die if you leave the lights on or any electrical equipment on after you turn the engine off. If this happens, you may be able to jump-start your vehicle with a booster battery.
  • Page 196 acid, have him or her drink lots of milk or water first, then Milk of Magnesia, a beaten egg, or vegetable oil. Call a doctor immediately. To avoid damaging your vehicle or your battery, and to avoid injury to yourself, follow these directions for preparing your vehicle to jump-start and connecting the jumper cables in the order they are given.
  • Page 197 Connecting the jumper cables 1. Connect one end of the first jumper cable to the positive (+) terminal of the discharged battery. (You can connect either jumper cable to the positive (+) terminal, as long as you use the same cable for both positive terminals.) Most jumper cables have a red cable and a black cable.
  • Page 198 The 3.8L SFI engine...
  • Page 199 The 4.6L SFI Engine...
  • Page 200 Jump-Starting 1. Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle. Run the engine at a moderate speed. 2. Let the discharged battery charge for a few minutes and then start the disabled vehicle. It may take a couple of tries before the vehicle starts.

  • Page 201: Changing A Tire

    NOTE: If your vehicle is equipped with a 3.8L engine you will need to perform additional steps after your vehicle has been jump started. See Readiness for Inspection/Maintenance Testing in Servicing Your Vehicle Chapter. Changing a Tire If you get a flat tire while you are driving, do not apply the brake heavily.
  • Page 202 When you drive with the temporary spare tire, DO NOT: exceed 50 mph (80 km/h) under any circumstances. load your vehicle so that it is heavier than the maximum vehicle load rating listed on the tire decal. tow a trailer. use tire chains on this tire.
  • Page 203 The spare tire location To remove the spare tire: 1. Remove the optional cargo net and storage bag. 2. Remove the spare tire cover. 3. Unscrew the wing-nut holding down the spare tire. 4. Lift out the spare tire, jack, and lug wrench. Preparing to Change the Tire 1.
  • Page 204 When one of the back wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) or 1 (First). To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the wheel (both directions) that is diagonally opposite (other side and end of the...
  • Page 205 Removing and Replacing the Tire 1. Find the jack notch next to the door of the tire that you are changing. Put the jack in the jack notch and turn the handle of the jack clockwise until the wheel is completely off the ground.
  • Page 206 The improper lift point NOTE: Never use the differential housing as a lift point. 2. Turn the jack handle clockwise until the wheel clears the ground. Remove the wheel lug nuts. 3. Replace the flat tire with the spare tire, making sure that the air valve stem is facing outward.
  • Page 207 6. Remove the jack and fully tighten the lug nuts in the order shown in the following illustration. As soon as possible, have your dealer or a qualified service technician check the lug nuts for proper torque specifications. The lug nuts on the wheel 7.
  • Page 208 (not to the dealer) to get a replacement key. NOTE: If entire lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln-Mercury dealer who has access to a master set of keys. NOTE: DO NOT USE A POWER IMPACT WRENCH ON THE LUG NUT KEY.

  • Page 209: Towing Your Vehicle

    Mustang Cobra/Convertible DO NOT TOW WITH SLINGBELT EQUIPMENT. Ford Motor Company has not developed or approved a T-hook sling-type procedure. Use wheel lift or flatbed equipment. If your vehicle is to be towed from the rear...
  • Page 210 When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and towing procedures for your vehicle.

  • Page 211: Customer Assistance

    Customer Assistance Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators who put you in touch with the help you need if you experience a problem with your vehicle. This complimentary service is provided to you throughout your warranty period of 3 years or 36,000 miles (60,000 km), whichever comes first.
  • Page 212 If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help.
  • Page 213 If you live in Canada and have any questions or concerns that the dealership cannot answer, contact the Customer Assistance Centre. Please have the following information available when contacting Ford Customer Assistance: your telephone number (both business and home) the name of the dealer and the city where the...

  • Page 214: The Dispute Settlement Board

    Review? The Board reviews unresolved warranty performance complaints on Ford, Mercury and Lincoln cars and Ford and Mercury Light Trucks under warranty that have not been resolved by a dealer or Ford Motor Company. The Board does not review issues involving:...
  • Page 215 How Does the Board Work? The Board has four members: three consumer representatives a Ford or Lincoln-Mercury dealer Consumer candidates for Board membership are recruited and trained by an independent consulting firm. Dealers are chosen because of their business leadership qualities.
  • Page 216 The decisions of the Board are binding on the dealer and Ford, but customers may have other options available to them under state or federal law. The decisions of the Board, however, may be...
  • Page 217 Board address. At the same time, your dealer and Ford Motor Company representative are asked to submit statements. To review your case properly, the Board needs...

  • Page 218: Reporting Safety Defects

    National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
  • Page 219 Mediation/Arbitration Program (Canada Only) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
  • Page 220 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused by use of improper fuel.
  • Page 221 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write to: If you are in other foreign countries, contact the nearest Ford dealership.
  • Page 222 Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
  • Page 223 Safety, Comfort, and Convenience...
  • Page 224 NOTE: Use only hook and pad design roof racks. Follow all manufacturers recommendations including vehicle speed, rack loads and tie down procedures. Also, DO NOT over torque the hook clamp, as vehicle damage may occur. NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front...
  • Page 225 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
  • Page 229 Servicing Your Mustang Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible. To help you:...
  • Page 230 Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
  • Page 231 If you must work with the engine running, avoid wearing loose clothing or jewelry that could get caught in moving parts. Take appropriate precautions with long hair. Do not work on a vehicle in an enclosed space with the engine running, unless you are sure you have enough ventilation.
  • Page 232 RWARNING Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Opening the Hood 1. Inside the vehicle, pull the hood release located under the lower left corner of the instrument panel.

  • Page 233: Engine Compartment

    Engine Compartment Your vehicle has one of these types of engines: a 3.8 liter SFI engine a 4.6 liter SFI engine The following pages show diagrams of each engine type and where to find items that you should regularly service.

  • Page 236: Filling The Fuel Tank

    Cleaning the Engine A clean engine is more efficient because a buildup of grease and dirt acts as an insulator, keeping the engine warmer than usual. Extreme care must be used if a power washer is used to clean the engine. The high pressure fluid could penetrate sealed parts and assemblies causing damage or malfunctions.
  • Page 237 2. Put the nozzle all the way inside the fuel filler pipe before pumping the fuel. NOTE: If you spill any fuel on the body of your vehicle, clean it off immediately. The fuel may dull or soften the paint if you do not wash it off.
  • Page 238 Octane recommendations Your engine is designed to use fuel with an octane rating of 87. In most cases it is not necessary to use a fuel with an octane rating higher than 87. At service stations, the octane rating is displayed in a label on the pumps. Using a fuel with a lower octane rating can cause persistent and heavy knocking, which can damage the engine.
  • Page 239 Reformulated gasoline is also required in certain areas of the U.S. These fuels are designed to further reduce emissions from your vehicle. Generally, you should not experience difficulties operating your vehicle on fuels containing oxygenates. We encourage you to use these fuels.

  • Page 240: Calculating Fuel Economy

    Gasoline and gasoline blends may contain small amounts of carcinogens, such as benzene. Long-term exposure to unleaded gasoline vapors has caused cancer in laboratory animals. If you are taking the medication “Antabuse” or other forms of disulfiram for the treatment of alcoholism, vapor or skin contact with a gasoline-methanol blend may cause the same kind of adverse reaction as drinking an alcoholic...
  • Page 241 3. After at least 3-5 tankfuls, fill the fuel tank and record the final odometer reading. 4. Use these equations to calculate your fuel economy: English: MPG = (total miles driven) (gallons used) Metric: L/100k = (liters used) (100 kilometers) Comparisons With EPA Estimates EPA fuel economy figures are obtained from laboratory tests under simulated road conditions...
  • Page 242 Check tires for excessive wear or worn edges Check the tire pressure at least monthly Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification WSS-M2C153-F and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container.
  • Page 243 Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG Additional engine oil additives, oil treatments or engine treatments Engine oils with an SAE 5W-30 viscosity are PREFERRED for your vehicle. They provide the best engine performance, fuel economy and engine protection for all climates down to -15˚F (-25˚C).
  • Page 244 5. Wipe the dipstick clean and put it back into position, making sure it is fully seated. Engine oil dipstick — 4.6 liter engines Engine oil dipstick — 3.8 liter engines 6. Carefully, pull the dipstick out again. If the oil level is below the “ADD 1 QT”...
  • Page 245 It may be necessary to add some oil between oil changes. Make sure you use a CERTIFIED engine oil of the preferred viscosity. Your vehicle’s warranty coverage may not apply if engine damage is caused by the use of improper engine oil.

  • Page 246: Engine Coolant

    RWARNING Continuous contact with USED motor oil has caused cancer in laboratory mice. Protect your skin by washing with soap and water. Engine Coolant Checking the Engine Coolant NOTE: Be sure to read and understand Precautions When Servicing Your Vehicle at the beginning of this chapter. RWARNING The cooling fan is automatic and may come on at any time.
  • Page 247 The engine coolant recovery reservoir — 3.8L The engine coolant recovery reservoir — 4.6L engines...
  • Page 248 Checking Hoses Inspect all engine and heater system hoses and hose connections for deterioration, leaks, and loose hose clamps as specified in the Maintenance Schedule and Record booklet. Repair or replace with Motorcraft hoses or equivalent as necessary. Adding Engine Coolant RWARNING Do not put engine coolant in the container for the windshield washer fluid.
  • Page 249 50/50 or appropriate mixture of water and the type of engine coolant that Ford specifies. You may add water by itself only in an emergency, but you should replace it with a 50/50 or appropriate mixture as soon as possible.
  • Page 250 Use Ford Premium Cooling System Fluid E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or an equivalent engine coolant that meets Ford Specification ESE-M97B44-A. Leave the engine coolant in all year. Make sure that the coolant will not freeze at the temperature level in which you drive during winter months.
  • Page 251 Engine Coolant Drain and Flush Proper procedures for a complete coolant drain and flush of the cooling system can be found in the Car Service Manual. Following these recommended procedures will ensure that the specified coolant level and a 50/50 or appropriate mixture of coolant and water is maintained.
  • Page 252 Start and idle engine until the radiator upper hose is warm (this indicates the thermostat is open and coolant is flowing through the entire system). Immediately shut off engine. Cover cap completely with a thick cloth and cautiously remove radiator pressure cap and add a 50/50 mixture of recommended coolant and water until system is full.
  • Page 253 Continue to fill the reservoir until the coolant is at the FULL COLD level. Reinstall the pressure cap to the fully installed position. Start and idle the engine until the radiator upper hose is warm (this indicates the thermostat is open and coolant is flowing through the entire system).
  • Page 254 If the battery needs water quite often, have the charging system checked for a possible malfunction. Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol Because your vehicle’s engine is electronically...
  • Page 255 NOTE: If your vehicle is equipped with a 3.8L engine you will need to perform additional steps after the battery has been disconnected, jump started or replaced. See Readiness for Inspection/Maintenance Testing in Servicing Your Vehicle chapter. Windshield Washer Fluid and Wipers Washer Fluid Check the level of the windshield washer fluid...
  • Page 256 RWARNING Do not put windshield washer fluid in the container for the engine coolant. Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]).
  • Page 257 Drive at safe speeds. If you do not take these precautions, your tires may fail or go flat. Ford Motor Company recommends obeying posted speed limits. RWARNING Driving too fast for conditions creates the possibility of loss of vehicle control.
  • Page 258 At least once a month, check the pressure in all your vehicle’s tires, including the spare. Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 3 miles (5 km).
  • Page 259 Rotating the tires Replacing the Tires Replace any tires that show wear bands. When your tire shows a wear band, it has only 1/16 inch (2 mm) of tread left. A worn-out tire Because your vehicle’s tires may wear unevenly, you may need to replace them before a wear band appears across the entire tread.
  • Page 260 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation — Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
  • Page 261 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
  • Page 262 represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

  • Page 263: Automatic Transmission Fluid

    Put the chains on tightly with the ends held down securely. Verify that no chain touches any wiring, brake lines, or fuel lines. Follow the chain manufacturer’s instructions. Drive slowly. If you can hear the chains rub or bang against your vehicle, stop the vehicle and tighten the chains.
  • Page 264 Checking the Automatic Transmission Fluid It is preferable to check the transmission fluid level at normal operating temperature 150˚F-170˚F (66˚C-77˚C), after approximately 20 miles (30 km) of driving. However, if necessary, you can check the fluid level without having to drive 20 miles (30 km) to obtain a normal operating temperature if outside temperatures are above 50˚F (10˚C).
  • Page 265 NOTE: If the vehicle has been operated for an extended period at high speeds or in city traffic during hot weather, or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking. Adding Automatic Transmission Fluid Before adding any fluid, be sure that the correct type will be used.

  • Page 266: Brake Fluid

    Manual Transmission Fluid The fluid level and quality should not deteriorate under normal driving conditions. However, it is suggested that you have the fluid level checked occasionally. If fluid is required, see Lubricant Specifications in the Index. The Clutch The clutch on your vehicle is operated by a cable that adjusts itself with a little help from you.
  • Page 267 If the fluid is low, carefully clean and remove the cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AA, C6AZ-19542-BA, or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.

  • Page 268: Power Steering Fluid

    The brake fluid reservoir — 4.6L engines If you find that the fluid level is excessively low — below the seam or ridge on the outside of the plastic reservoir — have the brake system inspected. RWARNING Do not let the reservoir for the master cylinder run dry.
  • Page 269 2. While the engine idles, turn the steering wheel back and forth several times. Make sure that the cap assembly is installed at this time. 3. Turn the engine off. 4. Check the fluid level on the dipstick (which is highlighted in yellow in your vehicle). The fluid level should be between the arrows in the FULL HOT range, which is marked on the side of the dipstick, opposite the side...
  • Page 270 Use only power steering fluid that meets Ford Specification Mercon ATF XT-2-QDX. If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid. This can damage the power steering pump.
  • Page 271 NOTE: Brake fluid and power steering fluid CAN NOT be mixed. Only add brake fluid to the brake master cylinder reservoir. Only add power steering fluid to the power steering reservoir. 3. Visually verify that the fluid level is above the MIN line adjacent to the reservoir “sight window.”...

  • Page 272: Circuit Breakers

    Fluid level for power steering Use only power steering fluid that meets Ford Specification Mercon ATF XT-2-QDX. NOTE: If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid. This can damage the power steering pump.
  • Page 273 The following charts tell you which fuses or circuit breakers protect the wiring for each electrical part of your vehicle. If a fuse blows or a circuit breaker opens a circuit, all the parts of your vehicle that use that circuit will not work. Once you have determined which fuses or circuit breakers to check, follow the procedures under Checking and replacing fuses or Checking and...
  • Page 274 The instrument panel fuse panel...
  • Page 275 The Instrument Panel Fuses, Circuit Breakers and Relays...
  • Page 276 These, like fuses, open when the circuit load exceeds their amperage rating. High current fuses may be purchased from your Ford or Lincoln-Mercury dealer. The high current fuse panel is located in the engine compartment on the left-hand fender apron.
  • Page 277 RWARNING Always disconnect the battery before servicing high current fuses. Ford recommends that high current fuses be replaced by a qualified technician. The high current fuse panel location...
  • Page 278 The high current fuse panel...
  • Page 279 The high current fuses and relays...
  • Page 281 Checking and Replacing Fuses If you need to check a fuse, follow these steps: 1. Find the fuse panel cover below and to left of the steering column, in the instrument panel. Pull outward on the handle below the word “fuses” to expose the fuse panel. Squeeze the two backing tabs and pull to remove the cover.
  • Page 282 RWARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. 5. Replace the cover. Even after you replace a fuse, it will continue to blow if you do not find what caused the overload.
  • Page 283 Since the circuit breaker for the headlamps is mounted in the headlamp switch, you must replace the entire switch to install a new circuit breaker. Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps tail lamps...
  • Page 284 Headlamp Bulb The headlamps on your vehicle use replaceable bulbs. When the lamp burns out, simply replace the bulb, rather than the whole lamp. RWARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
  • Page 285 Headlamp access covers 3. Lift the cover and find the bulb in the headlamp socket. 4. Remove the electrical connector from the bulb by lifting the connector clip upward while pulling the connector rearward. 5. Remove the retaining ring by turning counterclockwise 1/8 of a turn to free it from the socket.
  • Page 286 Installing the headlamp bulb 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the socket. You may need to turn the bulb left or right to line up the grooves in the plastic base with the tabs in the socket.
  • Page 287 Using the Right Bulbs...

  • Page 288: Emission Control System

    In general, maintenance, replacement, or service of the emissions control devices or systems in your new Ford Motor Company vehicle or engine may be performed at your expense by any automotive repair establishment or individual using automotive parts equivalent to...
  • Page 289 Ford strongly recommends the use of genuine Ford replacement parts. If other than Ford or Motorcraft parts or Ford authorized remanufactured parts are used for maintenance replacements or for the service of components...
  • Page 290 may be liable if their emission control device is removed or is prevented from working. Never use a metal exhaust collector when you service your vehicle. If the metal collector contacts any of your vehicle’s plastic trim or bumper parts they could melt or deform. Do not drive your vehicle if it does not operate properly.
  • Page 291 OBD II Drive Cycle The following steps must be run in the order shown. If steps 2 thru 9 are interrupted, repeat the preceding step. Any safe driving mode is acceptable between steps. Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
  • Page 292 6. Continue to drive the vehicle in city traffic at speeds between 25 and 40 mph (40-64 km/h) (manual transmissions primarily drive vehicles in 3rd and 4th gear when possible) for 15 minutes. During the 15 minute drive cycle the following modes must be achieved: a.
  • Page 293 Refill Capacities, Motorcraft Parts, and Lubricant Specifications Refill Capacities...
  • Page 294 NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required. Motorcraft Parts If a spark plug is removed for examination, it must be reinstalled in the same cylinder.
  • Page 295 Lubricant Specifications...

  • Page 296: Vehicle Storage

    NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required. Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer...
  • Page 297 Body Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear wheel housing and underside of front fenders. Periodically wash vehicles stored in exposed locations. Touch-up raw or primed metal to prevent rust. Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration.
  • Page 298 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system. Cooling system Protect against freezing temperatures.
  • Page 299 Label Locations...

  • Page 310: Electronic Sound Systems

    Index ABS warning light (see Anti-lock brake system) ..65 Accessory position on the ignition ..49 Accessory power source, power point outlet ..Additives, engine oil .
  • Page 311 Anti-theft lug nuts and key..Anti-theft system arming the system ..description ....disarming an untriggered system .
  • Page 312 Battery (continued) servicing ....voltage gauge ... . . 76 when storing your vehicle ..Brake fluid brake warning light .
  • Page 313 Canada, customer assistance ..Canada, warranty information ..Canadian Motor Vehicle Arbitration Plan (CAMVAP) ....Capacities for refilling fluids .
  • Page 314 Cleaning your vehicle (continued) engine compartment ..exterior ....exterior lamps ... . . 86 fabric .
  • Page 315 Customer Assistance Center, Ford (U.S.) . . Customer Assistance Centre, Ford of Canada ..Dashboard (see Instrument panel) ..79 Daytime running light system ..84 Defects, reporting .
  • Page 316 Doors ....lubricant specifications ..Driving under special conditions bad weather ... . . heavy load .
  • Page 317 Entry system, remote ..Exhaust fumes ....56 Extended Service Plan, Ford ..324 Index 49, 53 301–302...
  • Page 318 Ford Customer Assistance Center ..Ford Dispute Settlement Board ..Ford Extended Service Plan ..Ford Motor Company of Canada ..
  • Page 319 Fuel pump shut-off switch engine does not start ..57 starting after a collision ..57 Fuse panels engine compartment..high current fuse panel .
  • Page 320 Gearshift (continued) floor-mounted ... . locking the gearshift ..49 manual operation ... positions .
  • Page 321 Hood....latch location ... . . lubrication specifications ..release lever .
  • Page 322 Keys key in ignition chime ..51 positions of the ignition ..49 removing from the ignition ..50 stuck in lock position .
  • Page 323 Lights, warning and indicator (continued) safety belt ....66 service engine soon ... 70 theft system ....72 turn signal indicator.
  • Page 324 Mirrors....rearview ....side view mirrors ... side view mirrors (manual) .
  • Page 325 Power point electrical outlet ..Power steering dipstick ... . . driving with power steering ..fluid, checking and adding ..fluid, refill capacity .

  • Page 326: Roadside Emergencies

    Roadside assistance ... Roadside emergencies ..Rotating the tires ... . Safe driving tips .
  • Page 327 Seats (continued) adjusting the seat, manual ..adjusting the seats, power ..child safety seats ... . 30 cleaning upholstery .
  • Page 328 Speedometer ....75 Starting your vehicle preparing to start your vehicle ..52 starting a cold engine ..53 starting after a collision .
  • Page 329 Tires (continued) snow tires and chains ..spare tire ....storing your vehicle ..tire grades .
  • Page 330 Tune-up specifications (VECI) ..Turn signal ....91 indicator lights ... lever .
  • Page 331 Warranty Information Booklet ..Washer fluid reservoir ....windshield ....Weight limits (GAWR, GVWR) .
  • Page 332 Service Station Information...

This manual is also suitable for:

Mustang

Table of Contents