Ford MUSTANG Manual
  1. Manuals
  2. Brands
  3. Ford Manuals
  4. Automobile
  5. Mustang
  6. Manual

Ford MUSTANG Manual

Hide thumbs Also See for MUSTANG:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Ford MUSTANG

Summary of Contents for Ford MUSTANG

  • Page 3: Table Of Contents

    Table of Contents Introductory Information ....... 1 Safety Restraints ..........9 Starting Your Mustang ......... 49 Warning Lights and Gauges ....... 61 Instrument Panel Controls ......79 Steering Column Controls ......91 Features ............103 Electronic Sound Systems ......141 Driving Your Mustang .......

  • Page 4: Introductory Information

    Introductory Information Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
  • Page 5 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation.
  • Page 6 Canadian Owners — French Version French Owner Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.
  • Page 7 If you lose your Warranty Information Booklet, you can get a new one free of charge. Contact any Ford or Lincoln-Mercury dealer, or refer to the addresses and phone numbers on the first page of this owner guide.
  • Page 8 The break-in period for new brake linings lasts for 100 miles (160 km) of city driving or 1,000 miles (1,600 km) of highway driving. Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in”...
  • Page 9 Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized its dealers to repair, at no charge to the owner, the surfaces of new vehicles damaged by...
  • Page 10 Cleaning Chrome and Aluminum Parts Wash chrome and aluminum parts with a mild detergent. Do not use steel wool, abrasive cleaners, fuel, or strong detergents. Cleaning Plastic Parts Some of your vehicle’s exterior trim parts are plastic. Clean with a tar and road oil remover if necessary.

  • Page 11: Safety Restraints

    Safety Restraints Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada the law requires their use. Safety belts provide best restraint when: the seatback is upright the occupant is sitting upright (not slouched) the lap belt is snug and low on the hips...
  • Page 12 Failure to follow these precautions could increase the risk and/or severity of injury in a collision. RWARNING Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies...
  • Page 13 RWARNING Lock the doors of your vehicle before driving to lessen the risk of the door coming open in a collision. Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, corner hard or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap and shoulder belt...
  • Page 14 Fastening the front seat combination lap and shoulder belt (coupe models) Fastening the front seat combination lap and shoulder belt (convertible models)
  • Page 15 Fastening the rear seat combination lap and shoulder belt coupe and convertible NOTE: Be sure to read and understand Important Safety Belt Information at the beginning of this chapter. Safety Belts for Front Passenger (Coupe Only) and Rear (Coupe and Convertible) Outboard Seating Positions Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of...
  • Page 16 Automatic locking mode In this operating mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled, and does not allow the occupant freedom of movement. This mode provides the following: A tight lap/shoulder belt fit on the occupant.
  • Page 17 NOTE: When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch back to the vehicle sensitive (emergency) locking mode. See the detailed instructions under Safety Seats for Children in this chapter. Front Passenger Lap Belt Retractor (Convertible Only) Your convertible is equipped with a dual locking mode retractor on the lap belt part of the...
  • Page 18 RWARNING Never install a rear-facing child seat or infant carrier in the right front passenger seat. 1. Buckle the lap/shoulder belt. 2. Grasp the lap portion of the belt below the child seat label. Pull upward until all of the belt is extracted and a click is heard.
  • Page 19 RWARNING The lap belts should fit snugly and as low as possible around the hips, not around the waist. RWARNING Failure to follow these precautions could increase the risk and/or severity of injury in a collision. 1) Use the shoulder belt on the outside shoulder only.
  • Page 20 Unfastening the Mustang convertible front outboard lap/shoulder belts 2. While the belt retracts, guide the tongue to its stowed position. If you do not guide the tongue, it may strike you or part of the vehicle. 3. (Coupe only). Place the belt in the belt holder at the top of the seatback.
  • Page 21 Belt holder location — coupe only 4. (Convertible only). Place the shoulder belt in the belt holder at the top of the seatback and place the lap belt in the belt guide at the side of the seat cushion. The retracted belt should be stored on this holder and in the belt guide when not in use, except when a passenger is entering or leaving the rear seat...
  • Page 22 Belt holder location — convertible only RWARNING The shoulder belt must always be in the belt holder when the belt is in use. Safety Belt Extension Assembly For some people, the safety belt may be too short even when it is fully extended. You can add about eight inches (20 cm) to the belt length with a safety belt extension assembly (part number 611C22).
  • Page 23 (slide bar) (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
  • Page 24 Air Bag Supplemental Restraint System (SRS) The driver and right front passenger air bags are Supplemental Restraint Systems (SRS), provided at these seating positions in addition to the lap/shoulder belt, and are designed to supplement the protection provided to properly belted occupants in moderate to severe frontal collisions.
  • Page 25 The Importance of Being Properly Seated In a collision, the air bag must inflate extremely fast to help provide additional protection for you. In order to do this, the air bag must inflate with considerable force. If you are not seated in a normal riding position with your back against the seatback, the air bag may not protect you properly and could possibly hurt you as it...
  • Page 26 move the seat to the most rearward position if possible and use the safety belts. Children weighing less than 40 lbs. (18 kg) always should use child or infant seats. RWARNING When using forward-facing child seats move the passenger seat as far back from the instrument panel as possible.
  • Page 27 For further information about the proper mounting of equipment in the front seat of this vehicle, please refer to Ford’s brochure entitled Some Important Information About Air Bag Supplemental Restraint System which can be obtained by calling Helm Inc. at 1-800-782-4356.
  • Page 28 If a collision occurs, the sensors sense the severity of the impact and activates the air bags if necessary. The air bag system is designed to deploy in frontal and front-angled collisions more severe than hitting a parked vehicle (of similar size and weight) head-on at about 28 mph (45 km/h).
  • Page 29 Inflated right front passenger side air bag RWARNING If the air bag is inflated, THE AIR BAG WILL NOT FUNCTION AGAIN AND MUST BE REPLACED IMMEDIATELY. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
  • Page 30 If any of these things happen, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the air bag Supplemental Restraint System may not function properly in the event of a collision.
  • Page 31 RWARNING Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. RWARNING Passengers should not be allowed to ride in the cargo area. Persons not riding in a seat with a fastened seat belt are much more likely to suffer serious injury in a collision.
  • Page 32 Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
  • Page 33 RWARNING REAR-FACING INFANT SEATS SHOULD NEVER BE USED IN THE FRONT SEAT. REAR-FACING INFANT SEATS MUST ALWAYS BE PLACED IN THE REAR SEAT. Failure to follow these instructions could result in serious injury. All child restraint systems are designed to be secured in vehicle seats by lap belts or by the lap portion of a lap-shoulder belt.
  • Page 34 Installing Safety Seats in the Front Seat — Convertible Your Mustang Convertible is equipped with a dual locking mode retractor on the lap belt portion of the lap/shoulder belt at the front passenger seat. The automatic locking mode must be used when installing a child seat in the front passenger seat.
  • Page 35 3. Following the child seat manufacturer’s instructions, route the lap/shoulder belt through the child seat or infant carrier and insert the belt tongue into the buckle until you hear and feel the latch engage, Figure 2. Routing the lap/shoulder belt...
  • Page 36 4. Grasp the lap portion of the belt below the child seat label. Pull upward until all of the belt is extracted and a click is heard. At this time, the lap belt retractor is in the automatic locking mode (child seat restraint mode), Figure 3.
  • Page 37 5. Allow the belt to retract. A clicking sound will be heard as the belt retracts. This indicates the retractor is in the automatic locking mode, Figure 4. Allowing belt to retract...
  • Page 38 6. Push down on the child seat while you pull down on the belt to remove any slack in the belt, Figure 5. Removing slack from the belt...
  • Page 39 7. Before placing the child in the child seat or infant carrier, forcibly tilt the seat from side to side, and also tug it forward to make sure that the seat is securely held in place, Figure 6. Checking that the seat is secure...
  • Page 40 8. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor, if you cannot, the belt is in the automatic locking mode, Figure 7. Checking the retractor 9. Check to make sure that the child seat or infant carrier is properly secured prior to each use.
  • Page 41 Installing Safety Seats in the Front Seat (Coupe only) and Rear Seating Positions (Coupe and Convertible) For seating positions equipped with a dual locking mode retractor, use the following procedure. If you choose to install a child safety seat or infant carrier in the front seating positions, move vehicle seat as far back as possible.
  • Page 42 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. See Figure 2. Be sure that the belt webbing is not twisted. Routing the lap/shoulder belt 4.
  • Page 43 Buckling the belt 5. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child seat restraint mode). See Figure 4.
  • Page 44 Setting the retractor to automatic locking mode 6. Allow the belt to retract. Pull up on the shoulder webbing. A clicking sound will be heard as the belt retracts. This indicates the retractor is in the automatic locking mode. Push down on the child seat while you pull up on the belt to remove any slack in the belt.
  • Page 45 Allowing shoulder belt to retract Removing slack from belt...
  • Page 46 7. Before placing the child in the child seat, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place. See Figure 7. Checking that the seat is secure...
  • Page 47 8. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor. If you cannot, the belt is in the automatic locking mode. See Figure 8. Checking the retractor 9. Check to make sure that the child seat is properly secured prior to each use.
  • Page 48 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and...
  • Page 49 belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion.

  • Page 50: Starting Your Mustang

    Starting Your Mustang Ignition Understanding the Positions of the Ignition The positions of the key in the ignition ACCESSORY allows some of your vehicle’s electrical accessories such as the radio and the windshield wipers to operate while the engine is not running.
  • Page 51 ON allows you to test your vehicle’s warning lights (except the brake system warning light) to make sure they work before you start the engine. The key returns to the ON position once the engine is started and remains in this position while the engine runs.
  • Page 52 NOTE: If your vehicle has an automatic transmission, the gearshift lever must be in the P (Park) position to remove the key from the ignition. If the key is stuck in the LOCK position, move the steering wheel left or right until the key turns freely.
  • Page 53 Starting Your Vehicle Preparing to Start Your Vehicle RWARNING Do not start your vehicle in a closed garage or other enclosed area. Never sit in a stopped vehicle for more than a short period of time with the engine running. Exhaust fumes are toxic.
  • Page 54 Starting Your Engine To start your engine: 1. Follow the steps under Preparing to Start Your Vehicle at the beginning of this section. 2. Turn the ignition key to the ON position. 3. DO NOT depress the accelerator pedal when starting your engine.
  • Page 55 Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. After you start the engine, let it idle for a few seconds. Keep your foot on the brake pedal and put the gearshift lever in gear.
  • Page 56 To turn the heater on, simply plug it into a grounded 110-volt outlet. Ford recommends that you use a 110-volt circuit that is protected by a ground fault circuit interrupter.
  • Page 57 For best results, plug the heater in at least three hours before you start your vehicle. Using the heater for longer than three hours will not damage the engine, so you can plug it in at night to start your vehicle the following morning.
  • Page 58 If the engine is idling while you are stopped in an open area for long periods of time, open the windows at least one inch (2.5 cm). Also, the heating or air conditioning system should be set to any function except MAX A/C or AUTO. If you use the heater, set the fan speed on MEDIUM or HIGH with the function control knob at any desired position.
  • Page 59 The fuel pump shut-off switch RWARNING If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service.
  • Page 60 5. Check under the vehicle again for leaking fuel. If you see or smell fuel, do not start your vehicle again. If you do not see or smell fuel, you can try to start your vehicle again. 6. Check all vehicle warning lights before driving the vehicle.

  • Page 61: Warning Lights And Gauges

    Warning Lights and Gauges The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles.
  • Page 64 The Cluster The following warning lights and gauges are on the cluster. All of the warning lights and gauges alert you to possible problems with your vehicle. Some of the lights listed are optional. The following sections detail what each of these indicators means.
  • Page 65 Anti-Lock Brake System Light (If equipped) This warning light will go on each time you start your vehicle. If it remains on for longer than five seconds, you should shut off your engine and restart. If the anti-lock brake light stays on, this indicates that the anti-lock feature is disabled and should receive immediate attention by a qualified service technician.
  • Page 66 1. Park your car on level ground, and turn off the engine and allow a few minutes for the engine oil to drain back into the oil pan. 2. Use the dipstick to check the oil. If the level is low, add oil, but do not overfill. See Engine Oil Recommendations in the Index.
  • Page 67 If there is a problem with the system, two things may happen: the readiness light will either flash or stay lit up, or you will hear a beeping sound. If either of these things happen, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately.
  • Page 68 Low Coolant Warning Light (4.6L Engine Only) This light tells you that the coolant is low inside the coolant recovery bottle and that you should add more coolant. This light comes on for a few seconds when your ignition key is turned to start, but should turn off when the engine starts.

  • Page 69: Driving Your Mustang

    O/D OFF mode was selected when the vehicle was last shut off. For more information see Driving Your Mustang. NOTE: If the light does not come on when the TCS is depressed or if the light flashes...
  • Page 70 High Beam Light This light comes on when the headlamps are turned to high beam or when you flash the lights. Check Engine Warning Light The Powertrain On-Board Diagnostic II (OBD II) system consists of the hardware and software necessary to monitor the operation of the powertrain.
  • Page 71 The improper lift point NOTE: Never use the differential housing as a lift point. 2. Turn the jack handle clockwise until the wheel clears the ground. Remove the wheel lug nuts. 3. Replace the flat tire with the spare tire, making sure that the air valve stem is facing outward.
  • Page 72 6. Remove the jack and fully tighten the lug nuts in the order shown in the following illustration. As soon as possible, have your dealer or a qualified service technician check the lug nuts for proper torque specifications. The lug nuts on the wheel 7.
  • Page 73 Anti-Theft Wheel Lug Nuts (If equipped) The aluminum wheels on Mustang 4.6L engine vehicles are secured with locking lug nuts. One of the lug nuts on each wheel must be removed and installed with a special key.
  • Page 74 Mustang Cobra/Convertible DO NOT TOW WITH SLINGBELT EQUIPMENT. Ford Motor Company has not developed or approved a T-hook sling-type procedure. Use wheel lift or flatbed equipment. If your vehicle is to be towed from the rear...
  • Page 75 When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and towing procedures for your vehicle.

  • Page 76: Customer Assistance

    Customer Assistance Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators who put you in touch with the help you need if you experience a problem with your vehicle. This complimentary service is provided to you throughout your warranty period of 3 years or 36,000 miles (60,000 km), whichever comes first.
  • Page 77 If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help.
  • Page 78 If you live in Canada and have any questions or concerns that the dealership cannot answer, contact the Customer Assistance Centre. Please have the following information available when contacting Ford Customer Assistance: your telephone number (both business and home) the name of the dealer and the city where the...
  • Page 79 Review? The Board reviews unresolved warranty performance complaints on Ford, Mercury and Lincoln cars and Ford and Mercury Light Trucks under warranty that have not been resolved by a dealer or Ford Motor Company. The Board does not review issues involving:...
  • Page 80 How Does the Board Work? The Board has four members: three consumer representatives a Ford or Lincoln-Mercury dealer Consumer candidates for Board membership are recruited and trained by an independent consulting firm. Dealers are chosen because of their business leadership qualities.
  • Page 81 The decisions of the Board are binding on the dealer and Ford, but customers may have other options available to them under state or federal law. The decisions of the Board, however, may be...
  • Page 82 Board address. At the same time, your dealer and Ford Motor Company representative are asked to submit statements. To review your case properly, the Board needs...

  • Page 83: Reporting Safety Defects

    National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
  • Page 84 Mediation/Arbitration Program (Canada Only) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
  • Page 85 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused by use of improper fuel.
  • Page 86 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write to: If you are in other foreign countries, contact the nearest Ford dealership.

  • Page 87: Accessories

    Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
  • Page 88 Safety, Comfort, and Convenience...
  • Page 89 NOTE: Use only hook and pad design roof racks. Follow all manufacturers recommendations including vehicle speed, rack loads and tie down procedures. Also, DO NOT over torque the hook clamp, as vehicle damage may occur. NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front...
  • Page 90 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.

  • Page 94: Servicing Your Mustang

    Servicing Your Mustang Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible. To help you:...
  • Page 95 Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
  • Page 96 If you must work with the engine running, avoid wearing loose clothing or jewelry that could get caught in moving parts. Take appropriate precautions with long hair. Do not work on a vehicle in an enclosed space with the engine running, unless you are sure you have enough ventilation.
  • Page 97 RWARNING Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Opening the Hood 1. Inside the vehicle, pull the hood release located under the lower left corner of the instrument panel.
  • Page 98 Engine Compartment Your vehicle has one of these types of engines: a 3.8 liter SFI engine a 4.6 liter SFI engine The following pages show diagrams of each engine type and where to find items that you should regularly service.
  • Page 101 Cleaning the Engine A clean engine is more efficient because a buildup of grease and dirt acts as an insulator, keeping the engine warmer than usual. Extreme care must be used if a power washer is used to clean the engine. The high pressure fluid could penetrate sealed parts and assemblies causing damage or malfunctions.
  • Page 102 2. Put the nozzle all the way inside the fuel filler pipe before pumping the fuel. NOTE: If you spill any fuel on the body of your vehicle, clean it off immediately. The fuel may dull or soften the paint if you do not wash it off.
  • Page 103 Octane recommendations Your engine is designed to use fuel with an octane rating of 87. In most cases it is not necessary to use a fuel with an octane rating higher than 87. At service stations, the octane rating is displayed in a label on the pumps. Using a fuel with a lower octane rating can cause persistent and heavy knocking, which can damage the engine.
  • Page 104 Reformulated gasoline is also required in certain areas of the U.S. These fuels are designed to further reduce emissions from your vehicle. Generally, you should not experience difficulties operating your vehicle on fuels containing oxygenates. We encourage you to use these fuels.
  • Page 105 Gasoline and gasoline blends may contain small amounts of carcinogens, such as benzene. Long-term exposure to unleaded gasoline vapors has caused cancer in laboratory animals. If you are taking the medication “Antabuse” or other forms of disulfiram for the treatment of alcoholism, vapor or skin contact with a gasoline-methanol blend may cause the same kind of adverse reaction as drinking an alcoholic...
  • Page 106 3. After at least 3-5 tankfuls, fill the fuel tank and record the final odometer reading. 4. Use these equations to calculate your fuel economy: English: MPG = (total miles driven) (gallons used) Metric: L/100k = (liters used) (100 kilometers) Comparisons With EPA Estimates EPA fuel economy figures are obtained from laboratory tests under simulated road conditions...
  • Page 107 Check tires for excessive wear or worn edges Check the tire pressure at least monthly Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification WSS-M2C153-F and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container.
  • Page 108 Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG Additional engine oil additives, oil treatments or engine treatments Engine oils with an SAE 5W-30 viscosity are PREFERRED for your vehicle. They provide the best engine performance, fuel economy and engine protection for all climates down to -15˚F (-25˚C).
  • Page 109 5. Wipe the dipstick clean and put it back into position, making sure it is fully seated. Engine oil dipstick — 4.6 liter engines Engine oil dipstick — 3.8 liter engines 6. Carefully, pull the dipstick out again. If the oil level is below the “ADD 1 QT”...
  • Page 110 It may be necessary to add some oil between oil changes. Make sure you use a CERTIFIED engine oil of the preferred viscosity. Your vehicle’s warranty coverage may not apply if engine damage is caused by the use of improper engine oil.
  • Page 111 RWARNING Continuous contact with USED motor oil has caused cancer in laboratory mice. Protect your skin by washing with soap and water. Engine Coolant Checking the Engine Coolant NOTE: Be sure to read and understand Precautions When Servicing Your Vehicle at the beginning of this chapter. RWARNING The cooling fan is automatic and may come on at any time.
  • Page 112 The engine coolant recovery reservoir — 3.8L The engine coolant recovery reservoir — 4.6L engines...
  • Page 113 Checking Hoses Inspect all engine and heater system hoses and hose connections for deterioration, leaks, and loose hose clamps as specified in the Maintenance Schedule and Record booklet. Repair or replace with Motorcraft hoses or equivalent as necessary. Adding Engine Coolant RWARNING Do not put engine coolant in the container for the windshield washer fluid.
  • Page 114 50/50 or appropriate mixture of water and the type of engine coolant that Ford specifies. You may add water by itself only in an emergency, but you should replace it with a 50/50 or appropriate mixture as soon as possible.
  • Page 115 Use Ford Premium Cooling System Fluid E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or an equivalent engine coolant that meets Ford Specification ESE-M97B44-A. Leave the engine coolant in all year. Make sure that the coolant will not freeze at the temperature level in which you drive during winter months.
  • Page 116 Engine Coolant Drain and Flush Proper procedures for a complete coolant drain and flush of the cooling system can be found in the Car Service Manual. Following these recommended procedures will ensure that the specified coolant level and a 50/50 or appropriate mixture of coolant and water is maintained.
  • Page 117 Start and idle engine until the radiator upper hose is warm (this indicates the thermostat is open and coolant is flowing through the entire system). Immediately shut off engine. Cover cap completely with a thick cloth and cautiously remove radiator pressure cap and add a 50/50 mixture of recommended coolant and water until system is full.
  • Page 118 Continue to fill the reservoir until the coolant is at the FULL COLD level. Reinstall the pressure cap to the fully installed position. Start and idle the engine until the radiator upper hose is warm (this indicates the thermostat is open and coolant is flowing through the entire system).
  • Page 119 If the battery needs water quite often, have the charging system checked for a possible malfunction. Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol Because your vehicle’s engine is electronically...
  • Page 120 NOTE: If your vehicle is equipped with a 3.8L engine you will need to perform additional steps after the battery has been disconnected, jump started or replaced. See Readiness for Inspection/Maintenance Testing in Servicing Your Vehicle chapter. Windshield Washer Fluid and Wipers Washer Fluid Check the level of the windshield washer fluid...
  • Page 121 RWARNING Do not put windshield washer fluid in the container for the engine coolant. Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]).
  • Page 122 Drive at safe speeds. If you do not take these precautions, your tires may fail or go flat. Ford Motor Company recommends obeying posted speed limits. RWARNING Driving too fast for conditions creates the possibility of loss of vehicle control.
  • Page 123 At least once a month, check the pressure in all your vehicle’s tires, including the spare. Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 3 miles (5 km).
  • Page 124 Rotating the tires Replacing the Tires Replace any tires that show wear bands. When your tire shows a wear band, it has only 1/16 inch (2 mm) of tread left. A worn-out tire Because your vehicle’s tires may wear unevenly, you may need to replace them before a wear band appears across the entire tread.
  • Page 125 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation — Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
  • Page 126 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
  • Page 127 Snow tires must be the same size and grade as the tires you currently have on your vehicle. For your Mustang GT models equipped with 17 in. tires, to achieve the best traction during snow and ice conditions, purchase 245/45ZR17 mud and snow tires.
  • Page 128 Put the chains on tightly with the ends held down securely. Verify that no chain touches any wiring, brake lines, or fuel lines. Follow the chain manufacturer’s instructions. Drive slowly. If you can hear the chains rub or bang against your vehicle, stop the vehicle and tighten the chains.
  • Page 129 Checking the Automatic Transmission Fluid It is preferable to check the transmission fluid level at normal operating temperature 150˚F-170˚F (66˚C-77˚C), after approximately 20 miles (30 km) of driving. However, if necessary, you can check the fluid level without having to drive 20 miles (30 km) to obtain a normal operating temperature if outside temperatures are above 50˚F (10˚C).
  • Page 130 NOTE: If the vehicle has been operated for an extended period at high speeds or in city traffic during hot weather, or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking. Adding Automatic Transmission Fluid Before adding any fluid, be sure that the correct type will be used.
  • Page 131 Manual Transmission Fluid The fluid level and quality should not deteriorate under normal driving conditions. However, it is suggested that you have the fluid level checked occasionally. If fluid is required, see Lubricant Specifications in the Index. The Clutch The clutch on your vehicle is operated by a cable that adjusts itself with a little help from you.
  • Page 132 If the fluid is low, carefully clean and remove the cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AA, C6AZ-19542-BA, or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
  • Page 133 The brake fluid reservoir — 4.6L engines If you find that the fluid level is excessively low — below the seam or ridge on the outside of the plastic reservoir — have the brake system inspected. RWARNING Do not let the reservoir for the master cylinder run dry.
  • Page 134 2. While the engine idles, turn the steering wheel back and forth several times. Make sure that the cap assembly is installed at this time. 3. Turn the engine off. 4. Check the fluid level on the dipstick (which is highlighted in yellow in your vehicle). The fluid level should be between the arrows in the FULL HOT range, which is marked on the side of the dipstick, opposite the side...
  • Page 135 Use only power steering fluid that meets Ford Specification Mercon ATF XT-2-QDX. If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid. This can damage the power steering pump.
  • Page 136 NOTE: Brake fluid and power steering fluid CAN NOT be mixed. Only add brake fluid to the brake master cylinder reservoir. Only add power steering fluid to the power steering reservoir. 3. Visually verify that the fluid level is above the MIN line adjacent to the reservoir “sight window.”...
  • Page 137 Fluid level for power steering Use only power steering fluid that meets Ford Specification Mercon ATF XT-2-QDX. NOTE: If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid. This can damage the power steering pump.
  • Page 138 The following charts tell you which fuses or circuit breakers protect the wiring for each electrical part of your vehicle. If a fuse blows or a circuit breaker opens a circuit, all the parts of your vehicle that use that circuit will not work. Once you have determined which fuses or circuit breakers to check, follow the procedures under Checking and replacing fuses or Checking and...
  • Page 139 The instrument panel fuse panel...
  • Page 140 The Instrument Panel Fuses, Circuit Breakers and Relays...
  • Page 141 These, like fuses, open when the circuit load exceeds their amperage rating. High current fuses may be purchased from your Ford or Lincoln-Mercury dealer. The high current fuse panel is located in the engine compartment on the left-hand fender apron.
  • Page 142 RWARNING Always disconnect the battery before servicing high current fuses. Ford recommends that high current fuses be replaced by a qualified technician. The high current fuse panel location...
  • Page 143 The high current fuse panel...
  • Page 144 The high current fuses and relays...
  • Page 146 Checking and Replacing Fuses If you need to check a fuse, follow these steps: 1. Find the fuse panel cover below and to left of the steering column, in the instrument panel. Pull outward on the handle below the word “fuses” to expose the fuse panel. Squeeze the two backing tabs and pull to remove the cover.
  • Page 147 RWARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. 5. Replace the cover. Even after you replace a fuse, it will continue to blow if you do not find what caused the overload.
  • Page 148 Since the circuit breaker for the headlamps is mounted in the headlamp switch, you must replace the entire switch to install a new circuit breaker. Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps tail lamps...
  • Page 149 Headlamp Bulb The headlamps on your vehicle use replaceable bulbs. When the lamp burns out, simply replace the bulb, rather than the whole lamp. RWARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
  • Page 150 Headlamp access covers 3. Lift the cover and find the bulb in the headlamp socket. 4. Remove the electrical connector from the bulb by lifting the connector clip upward while pulling the connector rearward. 5. Remove the retaining ring by turning counterclockwise 1/8 of a turn to free it from the socket.
  • Page 151 Installing the headlamp bulb 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the socket. You may need to turn the bulb left or right to line up the grooves in the plastic base with the tabs in the socket.
  • Page 152 Using the Right Bulbs...
  • Page 153 In general, maintenance, replacement, or service of the emissions control devices or systems in your new Ford Motor Company vehicle or engine may be performed at your expense by any automotive repair establishment or individual using automotive parts equivalent to...
  • Page 154 Ford strongly recommends the use of genuine Ford replacement parts. If other than Ford or Motorcraft parts or Ford authorized remanufactured parts are used for maintenance replacements or for the service of components...
  • Page 155 may be liable if their emission control device is removed or is prevented from working. Never use a metal exhaust collector when you service your vehicle. If the metal collector contacts any of your vehicle’s plastic trim or bumper parts they could melt or deform. Do not drive your vehicle if it does not operate properly.
  • Page 156 OBD II Drive Cycle The following steps must be run in the order shown. If steps 2 thru 9 are interrupted, repeat the preceding step. Any safe driving mode is acceptable between steps. Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
  • Page 157 6. Continue to drive the vehicle in city traffic at speeds between 25 and 40 mph (40-64 km/h) (manual transmissions primarily drive vehicles in 3rd and 4th gear when possible) for 15 minutes. During the 15 minute drive cycle the following modes must be achieved: a.
  • Page 158 Refill Capacities, Motorcraft Parts, and Lubricant Specifications Refill Capacities...
  • Page 159 NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required. Motorcraft Parts If a spark plug is removed for examination, it must be reinstalled in the same cylinder.
  • Page 160 Lubricant Specifications...
  • Page 161 NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required. Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer...
  • Page 162 Body Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear wheel housing and underside of front fenders. Periodically wash vehicles stored in exposed locations. Touch-up raw or primed metal to prevent rust. Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration.
  • Page 163 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system. Cooling system Protect against freezing temperatures.
  • Page 164 Label Locations...

  • Page 175: Index

    Index ABS warning light (see Anti-lock brake system) ..65 Accessory position on the ignition ..49 Accessory power source, power point outlet ..Additives, engine oil .
  • Page 176 Anti-theft lug nuts and key..Anti-theft system arming the system ..description ....disarming an untriggered system .
  • Page 177 Battery (continued) servicing ....voltage gauge ... . . 76 when storing your vehicle ..Brake fluid brake warning light .
  • Page 178 Canada, customer assistance ..Canada, warranty information ..Canadian Motor Vehicle Arbitration Plan (CAMVAP) ....Capacities for refilling fluids .
  • Page 179 Cleaning your vehicle (continued) engine compartment ..exterior ....5–6 exterior lamps ... . . 86 fabric .
  • Page 180 Cruise control (see Speed control) ..97 Customer Assistance Center, Ford (U.S.) . . Customer Assistance Centre, Ford of Canada ..217, 223 Dashboard (see Instrument panel) ..79 Daytime running light system .
  • Page 181 Doors ....lubricant specifications ..Driving under special conditions bad weather ... . . heavy load .
  • Page 182 Entry system, remote ..Exhaust fumes ....56 Extended Service Plan, Ford ..324 Index...
  • Page 183 Ford Customer Assistance Center ..Ford Dispute Settlement Board ..Ford Extended Service Plan ..Ford Motor Company of Canada ..
  • Page 184 Fuel pump shut-off switch engine does not start ..57 starting after a collision ..57 Fuse panels engine compartment..high current fuse panel .
  • Page 185 Gearshift (continued) floor-mounted ... . locking the gearshift ..49 manual operation ... positions .
  • Page 186 Hood....latch location ... . . lubrication specifications ..release lever .
  • Page 187 Keys key in ignition chime ..51 positions of the ignition ..49 removing from the ignition ..50 stuck in lock position .
  • Page 188 Lights, warning and indicator (continued) safety belt ....66 service engine soon ... 70 theft system ....72 turn signal indicator.
  • Page 189 Mirrors....rearview ....side view mirrors ... side view mirrors (manual) .
  • Page 190 Power point electrical outlet ..Power steering dipstick ... . . 274–275 driving with power steering ..fluid, checking and adding ..fluid, refill capacity .
  • Page 191 Roadside assistance ... Roadside emergencies ..Rotating the tires ... . Safe driving tips .
  • Page 192 Seats (continued) adjusting the seat, manual ..adjusting the seats, power ..child safety seats ... . 30 cleaning upholstery .
  • Page 193 Speedometer ....75 Starting your vehicle preparing to start your vehicle ..52 starting a cold engine ..53 starting after a collision .
  • Page 194 Tires (continued) snow tires and chains ..spare tire ....storing your vehicle ..tire grades .
  • Page 195 Tune-up specifications (VECI) ..Turn signal ....91 indicator lights ... 72, 91 lever .
  • Page 196 Warranty Information Booklet ..Washer fluid reservoir ....windshield ....Weight limits (GAWR, GVWR) .
  • Page 197 Service Station Information...

Table of Contents