Advertisement
GENERAL
Installation of the unit must be accomplished by qualified
installation personnel working to all applicable local and
national codes. Improper installation of product could cause
injury or damage.
This unit is built to comply with applicable standards for
manufacturers. Included among those approval agencies
are: UL, NSF, ASME/Ntl.Bd., CSA, ETL, CE, and others.
Many local codes exist, and it is the responsibility of the
owner/installer to comply with these codes.
RECEIVING INSPECTION
Before uncrating, visually inspect the unit for evidence of
damage during shipping.
If damage is noticed, do not unpack the unit, follow
shipping damage instructions.
SHIPPING DAMAGE
INSTRUCTIONS
If shipping damage to the unit is discovered or
suspected, observe the following guidelines in preparing
a shipping damage claim.
1. Write down a description of the damage or the reason
for suspecting damage as soon as it is discovered.
This will help in filling out the claim forms later. If
possible, take a polaroid picture.
2. As soon as damage is discovered or suspected, notify
the carrier that delivered the shipment.
3. Arrange for the carrier's representative to examine the
damage.
4. Fill out all carrier claims forms and have the
examining carrier sign and date each form.
APPROXIMATE WEIGHTS
Tilting - Leg/Pedestal
Model #
Unit
Unit with
shipping box
KDL/P-25-T 185 lbs.
220 lbs.
KDL/P-40-T 240 lbs.
275 lbs.
KDL/P-60-T 310 lbs.
345 lbs.
KDL-80-T
380 lbs.
415 lbs.
KDL-100-T 440 lbs.
475 lbs.
KDL-125-T 500 lbs.
535 lbs.
KDL-150-T 560 lbs.
595 lbs.
Stationary - Full Jacketed
Model #
Unit
Unit with
shipping box
KDL-30-F
100 lbs.
135 lbs.
KDL-40-F
150 lbs.
185 lbs.
KDL-60-F
170 lbs.
205 lbs.
KDL-80-F
280 lbs.
315 lbs.
KDL-100-F 325 lbs.
360 lbs.
KDL-125-F 375 lbs.
410 lbs.
KDL-150-F 455 lbs.
490 lbs.
INSTALLATION
Stationary - Leg/Pedestal
Model #
Unit
Unit with
shipping box
KDL-25
135 lbs.
170 lbs.
KDL/P-40
195 lbs.
230 lbs.
KDL/P-60
225 lbs.
260 lbs.
KDL/P-80
255 lbs.
290 lbs.
KDL/P-100 325 lbs.
360 lbs.
KDL-125
375 lbs.
410 lbs.
KDL-150
455 lbs.
490 lbs.
KDL-200
525 lbs.
560 lbs.
KDL-250
590 lbs.
625 lbs.
Stationary/Tilting - SH Series
Model #
Unit
Unit with
shipping box
KDL-40-T/SH
195 lbs.
230 lbs.
KDL-60-T/SH
225 lbs.
260 lbs.
KDL-80-T/SH
255 lbs.
290 lbs.
UNCRATING
Caution:
Straps under tension and will snap when cut.
Carton may contain staples and Skid contains Nails.
Use proper safety equipment and precautions.
Unit is heavy use adequate help or lifting equipment as
needed.
1. Carefully cut any straps from container.
2. Lift off carton.
3. Inspect for hidden damage. If found refer to
"SHIPPING DAMAGE INSTRUCTIONS".
4. Cut strap holding unit.
5. Remove manual from kettle pot. Write down the model
# and serial# of the unit onto the front of this manual.
6. Lift kettle off skid and move kettle to its installation
location.
7. Discard packaging material according to local and or
state requirements.
VENTILATION
Operation of these units can produce significant levels of steam
and condensate, it is recommended they be installed under a
ventilation hood in a room which has provisions for
adequate make up air. Further information can be
obtained by referring to the U.S.A. National Fire Protection
Associations NFPA96 regulations. These standards have
also been adopted by the National Building Code in
Canada.
4.
Hide quick links:
Advertisement
