Advertisement
Available languages
Available languages
INSTALLATION (ACCESSORIES NO INCLUDED):
1. FLANGE
•
Manufacture the mould with the iron cable or bar according to its
design.
• Use the flanges to secure the luminous thread inside the cable.
• It is perfect for Artwork and lighting of buildings.
2. STEEL MESH
• Firstly make the design in its current size on paper.
• Place the steel mesh over the design, fix the luminous thread on the mesh
with flanges according to its drawing.
• It is perfect for Artwork.
3. SUCTION PADS
• Fix the suction pads on the glass surface or metal with glue.
• Use the flanges to fix the luminous thread to the suction pad.
• It is suitable to glass or metal surfaces.
1
2
3
CAUTIONS
• No use this product in contact with water or with wet hands.
• Never place or use this product close to heat sources (for instance:
heating).
• No connect this product while it remains rolled, it might set fire.
• Use only this product with enough ventilation and refrigeration.
• If you use this product outdoors, you must use as electrical outlet a IPX4
tigh-base.
• If you use this product outdoors, you must always use a Power Failure
Protection Switch (FI-30mA) between the Power Supplier (220-240V) and the
product.
• Protect all the cables against potential damages.
• The lamps are not exchangable.
• Under no circumstances should you beat this product with a hammer, it
might damage the lamps.
• If the product is mounted to hang freely, it must be adjusted to a steel
cable and be connected to it every 10 cm.
• If the luminous thread is going to use in permanent installations, you have
to take into account that it will lose progressively performance in white and
blue colors after many continuous hours.
CONNECTION TO THE POWER SUPPLIER
• Do not connect the luminous thread to the power supplier until the insta-
llation or the modification has been completed.
• Do not connect the luminous thread to the power supplier until the end
cap has been fixed with security to the edge of the luminous thread.
• Do not connect the garland to the power supplier while it is in its packa-
ge, unless the package has a decorative meaning.
• Make sure that the power supplier has not a higher voltage that the
luminous thread.
• It is recommended to use plug/ adapter with fuse in order to avoid any
damages from overload.
CONNECTION.
• Only can be connect between them those luminous thread with the
same voltage.
• When it is going to make connections between pieces from the luminous
thread, o the luminous thread with the power cord, make sure that both
parts keep the narrowest as possible.
• The connector pins and the copper wire of the luminous thread.
• The male and female connector.
• The length of the luminous thread has not to overcome the maximum
power load (Look the chart with the parametres)
• It is recommended to seal all the connectors with neutral adhesive silico-
ne in order to avoid the entry of moisture in the luminous thread.
THE CUT
• Cut the luminous thread exclusively along the crops marks.
• To avoid possible short-circuits, make sure that the copper wire is cut
clearly.
USE
• Warn the luminous thread by connecting it to the network before giving
shape to the design. Unplug it while you are applying the shape desired.
• Do not use the metal cable, which can be conductive, to tie the luminous
thread.
• Make sure that the luminous thread does not make contact with any
flammable material or that can be melting.
• Ensure that there is an appropriate ventilation around the luminous
thread, do not cover or install the luminous thread in an enclosed area.
• Do not dip the luminous thread under the water.
• Once the installation is planned, it is recommended that qualified staff
check it out.
• Throw away the product in the right place to do so.
YOUR LED LUMINOUS THREAD WORKS BETTER IF:
• Do not expose it directly to sunlight. UV radiation destroys the PVC cove-
rage of your luminous thread.
• If it is operated with supply of stable flow, changes in the voltage dama-
ge or shorten the useful life.
• It is used in a neutral chemical environment. Strong acids, alkaline, radio-
active, etc Damage the PVC coverage.
Advertisement
