System Switching On/Off; Switching On The System; Switching Off The System; Operating Mode - Elesa MPI-R10 Operating Instructions Manual

MPI-R10 MPI-R10-RF
Key Or Key
Combination
Programmable with one of
the following options (see the
_ _ 0 _ _ _ 0 voice of the menu
– cap. 8.3):
LOAdOrG [DEFAULT]: the key
SET ABS-REL
combination sets the absolute value
+
to the sum of the parameters Origin
and Offset.
OFF : the key combination is not
assigned to any function in the

operating mode.

Programmable with one of
the following options (see the
_ _ _ _ 0 _ 0 voice of the menu
– cap. 8.3):
tArGEtS : the keys combination
SET ORG
+
allows to load/program one of the
32 target positions. See 8.4
OFF [DEFAULT]: the key is not
assigned to any function in the
operating mode
Turn the indicator on hold
mm-inch SET
press the key
up sequence the indicator is ready
to be used (see chap. 4).
SET ABS-REL
mm-inch

6. System Switching on/off

6.1. Switching on the system

After you have read the section "Safety Instructions", proceed
by switching on the indicator.
To switch the indicator on:
mm-inch
- hold the key
SET
- press the key
The display will light up and the indicator is ready to be used.

6.2. Switching off the system

To switch the system off :
- enter the programming mode,
- select rESEt (see chap. 8.3)
SET
- press
ABS-REL
- press
mm-inch
- press
The display will turn off and the indicator will go into low
EN
power mode.
6
Operating Mode Programming Mode
NA
NA
mm-inch
then
SET
NA
. After the start-
When the
parameter is
selected, press the
key
point, press the
button
then press the key
mm-inch
will turn off and the
indicator will go into
low power mode
of the battery (see
chap. 4).
.
Models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings.
7. Operating mode
7.1. Absolute/incremental measuring mode selection
Press the key
measuring mode.
The measuring mode selected is shown on the display by
the symbols:
- ABS : absolute measuring mode.
- REL : incremental measuring mode.
It is possible to change the key
voice _ _ 0 _ _ _ _ (see chap.8.3).
The available options are:
- ArCLr (default): when relative measurement is selected,
the value is always reset to zero.
- Ar : passing from ABS to REL , the relative measurement
is not reset to zero.
In this case, the counter is set to zero by pressing
- OFF : the key
the selected measuring mode.
To program the parameters listed above, see chap. 8.3.

7.2. Unit of measure selection

Press the key
The options available are millimeters, inches and degrees.
The measuring mode selected is shown on the display by
rESEt
the symbols: mm for millimeters, inch for inches and with the
° suffix for degrees.
SET
. At this
It is possible to change the key
ABS-REL
voice 0 _ _ _ _ _ _ .
and
The available options are:
- ALL (default): units of measure that can be selected: mm,
; the display
inch, degree.
- nodEG : units of measure that can be selected: mm, inch.
- OFF : the key is disabled and does not allow changing the
selected measuring mode.
To program the parameters listed above, see chap. 8.3
7.3. Setting the origin
Press the key
measurement.
Keeping pressed the ORG key for three seconds, the display
will show the question Set Org. At this point press the key
to confirm or another key to cancel.
Confirming the setting of the origin, the display will be reset
to zero: this position of the sensor must be considered as the
origin of the following measurements.
7.4. Setting the absolute reference
After having selected the absolute measuring mode and
stopped the sensor in the starting or in the reference position,
press the key combination
to the sum of the values of the parameters Origin (absolute
value of reference) and the selected OFFS (compensation
value).
The value of compensation ( OFFSET ) allows you to adjust the
value shown on the display in such a way that takes into account,
Magnetic measuring system
ABS-REL
to select the absolute or incremental
ABS-REL
function by the menu
ABS-REL
is disabled and does not allow changing
mm-inch
to select the unit of measure.
mm-inch
function by the menu
ORG
for three seconds to set the origin of the
SET ABS-REL
+ to set the absolute value
SET ABS-REL
+
SET