ORiNG IPS-1080-24V Quick Installation Manual

ORing Industrial Networking Corp.
PoE
SWITCH
Q I
I N D U S T R I A L uick nstallation
Introduction
IPS-1080-24V is unmanaged PoE Ethernet switch with P.S.E. function.
24V supports Power over Ethernet, a system to transmit electrical power, along with
data, to remote devices over standard twisted-pair cable in an network.
24V switch h s 8X10/100Base-T(X) P.S.E. (Power Sourcing Equipment) ports. a
P.S.E. is a device (switch or hub for instance that will provide power in a PoE
setup. The wide operating temperature range from -40 C to 70 C can satisfy most of
operating environment. Therefore, the switch is one of the most reliable choices for
PoE Ethernet application.
Features
Provide 8x10/100Base-T(X) PoE (P.S.E.) ports
Supports IEEE 802.3at compliant PoE and total power budget is 120Watts with
maximum 30Watts per port
Advanced PoE power boost technology to support dual 24VDC power inputs
Support auto-negotiation and auto-MDI/MDI-X
Support store and forward transmission
Support flow control
Warning system by relay output
Slim type rigid IP-30 housing design
DIN-Rail and wall mounting enabled
Power Connection Guide
Warning !!!
！
24-36Vdc Input only
Check Polarity First.
PWR-2 1A@24V PWR-1
V2- V2+ V1- V1+
V-
Power
V+
Power
V+
Supply
V-
Supply
24-36 VDC
24-36VDC
Warning
Device
+24V GND
Power
Supply
DIP Switch Function
Description
DIP-1 DIP-2
OFF OFF Power failure relay alarm disabled
ON OFF PWR-1 failure, relay alarm enabled
OFF ON PWR-2 failure, relay alarm enabled
PWR-1 or PWR-2 failure,
ON ON
relay alarm enabled
Q I G
IPS-1080-24V
IPS-1080-24V
G
uide
Specifications
IPS-1080-
ORing Switch Model
IPS-1080-
Physical Ports
10/100 Base-T(X) Ports in RJ45
o o Auto MDI/MDIX with P.S.E.
Technology
Ethernet Standards
MAC Table
Processing
LED Indicators
Power indicator
Fault indicator
10/100Base-T(X)RJ45 Port
Indicator
Fault Contact
Relay
Power
Redundant Input power
Power consumption(Typ.)
Overload current protection
Reverse polarity protection
Physical Characteristic
Enclosure
Dimension (W x D x H)
Weight (g)
Environmental
Storage Temperature
G
Operating Temperature
Frame Ground
Operating Humidity
Regulatory Approvals
EMI
DIP Switch Select for
EMS
Power Alarm Relay Output
Shock
Free Fall
Vibration
Safety
Warranty
1907-2-29-IPS1080-0
IPS-1080-24V
8
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3x for Flow control
IEEE 802.3at PoE specification (up to 30 Watts per port for P.S.E.)
2048 MAC addresses
Store-and-Forward
Green: Power LED x2
Amber: Indicate PWR1 or PWR2 failure
Green for port Link/Act.
Green for PoE power injected.
Relay output to carry capacity of 1A at 24 VDC
Dual DC inputs 24~36VDC on 6-pin terminal block
4.32 Watts (power consumption of P.S.E. is not included)
Present
Not Present
IP-30
41 (W) x 94.9 (D) x 144.3 (H) mm (1.03 x 3.74 x 5.68 inches)
555g
-40 to 85 C (-40 to 185 F) o o
o o
-40 to 70 C (-40 to 158 F)
5% to 95% Non-condensing
FCC Part 15, CISPR (EN55022) class A
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
IEC60068-2-27
IEC60068-2-32
IEC60068-2-6
EN60950-1
5 years
PRINTED ON RECYCLED PAPER
Industrial Unmanaged PoE Switch
Practical Operation
IPS-1080A can be used in connecting several Ethernet devices like Ethernet I/O, IP-
Camera or other Ethernet switches. In addition, there are two r
inputs at terminal block to avoid interruption caused by power down.
primary DC power input fails, the backup power input will take over immediately to
guarantee a non-stop operation.
Connections of Ethernet devices
Front Panel
Power 2 LED
IPS-1080-24V
Power 1 LED Power Fault LED
P1 P2 Fault
8
7
6
5
4
Green: Link/Act
LAN Port
3
Green: PoE power injected
2
1
10/100TX
Quick Installation Guide
Version 1.0
edundant power
When the
A