Table of Contents
Advertisement
Quick Links
OPERATION INSTRUCTIONS FOR
CAR ALARM SYSTEM
WITH BACKUP BATERY & ENGINE IMMOBILISATION
SYSTEM FEATURES:
~ Suitable for all petrol and diesel engine vehicles with 12V negative earth batteries
~ Microprocessor Controlled
~ Supplied with Two Multi-Function Remote Controls
~ Engine Immobilisation (On Board Relay - 15Amp max)
~ Backup Battery Capability (9V)
~ Arming and Disarming Confirmation Beeps
~ Visual Arming and Disarming Confirmation via Indicators
~ Two Stage Shock Sensor (Pre-warning System)
~ Shock Sensor Sensitivity Programmable via Remote Control (8 Levels)
~ Shock Sensor Isolation Programmable via Remote Control
~ Negative Trigger Input (Doors, Boot, Bonnet)
~ Personal Panic Trigger via Remote Control
~ Automatic Siren Reset (30 Seconds)
~ Automatic Rearm (30 Seconds)
~ Selectable Current Sensing Circuit
~ Multi-tone Siren Sound or Select The Individual Tone You Prefer
~ Central Locking Control can be achieved by purchasing optional Rhino DLK Interface.
~ Supplied with Mounting Bracket, Hardware & Warning Stickers
~ Made in Taiwan
~ 12 Month Warranty
TO ARM/DISARM ALARM
The system is activated by pressing BUTTON 1 on the remote control transmitter once. The siren
will beep once. The indicators will flash once. The LED will start flashing. THE ALARM IS
NOW ARMED.
To deactivate the system, press BUTTON 1 again. The siren will beep twice. The indicators will
flash twice. The LED will stop flashing. THE ALARM IS NOW DISARMED.
(Note: Please wait at least five seconds after arming before pressing the remote control again - see
deleting shock sensor below).
COMPLETE DEACTIVATION can be achieved by turning the override keyswitch on the rear of
the alarm to the ON position - NOW OVERRIDE IS ON. The siren will sound immediately if
main power is removed while the system is armed. (If backup battery is installed).
AUTOMATIC REARM
RT65
RHINO
LED
BUTTON 2
BUTTON 1
Advertisement
Table of Contents
Related Manuals for RHINO RT65
Summary of Contents for RHINO RT65
- Page 1 ~ Selectable Current Sensing Circuit ~ Multi-tone Siren Sound or Select The Individual Tone You Prefer ~ Central Locking Control can be achieved by purchasing optional Rhino DLK Interface. ~ Supplied with Mounting Bracket, Hardware & Warning Stickers ~ Made in Taiwan...
- Page 2 TRIGGERING The siren sounds for 30 seconds then it will reset and rearm itself automatically. Your Rhino RT65 Alarm can be triggered by the following three methods: 1. TWO STAGE SHOCK SENSOR (PRE-WARNING SYSTEM) This special feature provides a two stage impact sensing system. It gives the security conscious owner a sensitive impact sensor that will give a potential thief prior warning that the vehicle is protected by this alarm system.
- Page 3 Please follow the wiring diagram below: +12V To orange wire from alarm (negative on arm -500mA) Interior light DOOR DELAY CIRCUIT Blue wire Place a diode here RHINO Door Switches Original wire to fuel pump/starter motor/ ign. coil PROGRAMMING AND ADJUSTMENT...
- Page 4 The Rhino RT65 Alarm System allows for customisation of both siren sound type and shock sensor sensitivity. Programming Remote Controls: To program, disconnect all power to alarm (i.e. remove fuse & backup battery). After 10 seconds replace the fuse. Press Button 1 on the first remote control. A single confirmation chirp should be heard.
- Page 5 30/40amp changeover relay as shown in earlier diagram, if greater than 15amp circuit is to be immobilised or this wire can be used to connect alarm to central locking - an optional RHINO DLKACCEL MODULE is required when connecting to vehicles that have existing central locking, or connect this wire to PIN 8 on RHINO’s CLKACCEL Central Locking Kit Control Module.
Need help?
Do you have a question about the RT65 and is the answer not in the manual?
Questions and answers