Table of Contents
Advertisement
Quick Links
OPERATION INSTRUCTIONS FOR
RHINO ACCEL PLUS
CAR ALARM SYSTEM
WITH BACKUP BATERY & ENGINE IMMOBILISATION
SYSTEM FEATURES:
~ Suitable for all petrol and diesel engine vehicles with 12V negative earth batteries
~ Microprocessor Controlled
~ Supplied with Two Multi-Function Remote Controls
~ Engine Immobilisation (On Board Relay - 15Amp max)
~ Backup Battery Capability (9V)
~ Arming and Disarming Confirmation Beeps
~ Visual Arming and Disarming Confirmation via Indicators
~ Two Stage Shock Sensor (Pre-warning System)
~ Shock Sensor Sensitivity Programmable via Remote Control (8 Levels)
~ Shock Sensor Isolation Programmable via Remote Control
~ Negative Trigger Input (Doors, Boot, Bonnet)
~ Personal Panic Trigger via Remote Control
~ Automatic Siren Reset (30 Seconds)
~ Automatic Rearm (30 Seconds)
~ Selectable Current Sensing Circuit
~ Multi-tone Siren Sound or Select The Individual Tone You Prefer
~ Central Locking Control can be achieved by purchasing optional Rhino DLK Interface.
~ Supplied with Mounting Bracket, Hardware & Warning Stickers
~ Made in Taiwan
~ 12 Month Warranty
TO ARM/DISARM ALARM
The system is activated by pressing BUTTON 1 on the remote control transmitter once. The siren will beep once. The
indicators will flash once. The LED will start flashing. THE ALARM IS NOW ARMED.
To deactivate the system, press BUTTON 1 again. The siren will beep twice. The indicators will flash twice. The LED
will stop flashing. THE ALARM IS NOW DISARMED.
(Note: Please wait at least five seconds after arming before pressing the remote control again - see deleting shock
sensor below).
COMPLETE DEACTIVATION can be achieved by turning the override keyswitch on the rear of the alarm to the
ON position - NOW OVERRIDE IS ON. The siren will sound immediately if main power is removed while the
system is armed. (If backup battery is installed).
ACCEL PLUS
LED
BUTTON 2
BUTTON 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for RHINO ACCEL PLUS
Summary of Contents for RHINO ACCEL PLUS
- Page 1 ~ Selectable Current Sensing Circuit ~ Multi-tone Siren Sound or Select The Individual Tone You Prefer ~ Central Locking Control can be achieved by purchasing optional Rhino DLK Interface. ~ Supplied with Mounting Bracket, Hardware & Warning Stickers ~ Made in Taiwan...
- Page 2 TRIGGERING The siren sounds for 30 seconds then it will reset and rearm itself automatically. Your Rhino Accel+ Alarm can be triggered by the following three methods: 1. TWO STAGE SHOCK SENSOR (PRE-WARNING SYSTEM) This special feature provides a two stage impact sensing system. It gives the security conscious owner a sensitive impact sensor that will give a potential thief prior warning that the vehicle is protected by this alarm system.
- Page 3 Install 30/40amp changeover relay as shown below: Please follow the wiring diagram below: +12V To orange wire from alarm (negative on arm -500mA) Interior light DOOR DELAY CIRCUIT Blue wire Place a diode here RHINO " Door Switches Original wire to fuel pump/starter motor/ ign. coil...
- Page 4 Choosing Siren Tone: Your Rhino Accel+ Alarm has the ability to sound in either 5 Tone or Single Tone operation. If you prefer to choose a single tone siren sound follow this procedure: 1. Within 10 seconds of disarming the alarm, press down both Buttons 1 & 2 on the remote control for two seconds. A single chirp will be given to confirm that you have entered the programming mode.
- Page 5 15amp circuit is to be immobilised or this wire can be used to connect alarm to central locking - an optional RHINO DLKACCEL MODULE is required when connecting to vehicles that have existing central locking, or connect this wire t o PIN 8 on RHINO’s CLKACCEL Central Locking Kit...
- Page 6 The Rhino Accel Plus does not provide dedicated central locking output wires i.e. separate lock & unlock pulses. Instead, the negative on arm wire from the Accel Plus can be utilised to activate our after-market central locking kit, provided the following simple modification is made to the central locking control module.
Need help?
Do you have a question about the ACCEL PLUS and is the answer not in the manual?
Questions and answers