Related Manuals for Royal Sovereign Fremont 65H
Summary of Contents for Royal Sovereign Fremont 65H
- Page 1 Owner's Manual Fremont 65H GRAPHIC LAMINATION PRODUCTS Please read and retain these instructions. To register your product, please go to www.royalsovereign.com www.royalsovereign.com Royal Sovereign International Inc.
-
Page 2: Table Of Contents
CONTENTS 1. Introduction 2. Safety Precautions 4. Installation 5. Product Identification 6. Control Panel 7. Using Foot Pedal 8. Loading Film 9. Threading Film 9.1 Laminting 9.2 Mounting 10. Adjusting the gap of both rollers 11. Maintenance 12. Troubleshooting 13. Specifications 14. -
Page 3: Introduction
Graphic Lamination Products Model Fremont 65H 1. IN TRODUCTION Thank you for choosing a Royal Sovereign laminator. It has been designed and manufactured to provide years of continuous service. For complete operating and maintenance information please read this manual thoroughly. Upon receipt of your laminator, please inspect the box, the machine and all other contents for shipping damage. -
Page 4: Safety Precautions
8. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing. 9. Keep out of reach of children. 10. Only Royal Sovereign authorized maintenance and service technicians should make repairs. 11. Do not attempt to laminate items that exceed total recommended material thickness for the unit. -
Page 5: Installation
Once the laminator is in place, lock the casters into position. Always unlock the casters when moving to a different location. ELECTRICAL REQUIREMENTS Royal Sovereign recommends that a licensed electrician ensures proper power installation to your laminator in accordance with electrical codes in your area. - Page 6 Owner's Manual Fremont 65H GRAPHIC LAMINATION Owner's Manual PRODUCTS Please read and retain these instructions. To register your product, please go to www.royalsovereign.com www.royalsovereign.com Royal Sovereign International Inc. Spare Motor Fuse - FUSE(50T) (6.3A) Spare Main Power Fuse - FUSE(65TS) 10A/20A...
-
Page 7: Product Identification
Fremont 65H 5. PRODUCT IDENTIFICATION Air Intake Film Tension Knob Shaft Release Liner Knob Speed Control Emergency Switch Button Roller Pressure Gauge Safety Sensor Pressure Regulating Valve Table Front Reversing Valve Caster Door Lock Gap Adjustment Foot Switch Shaft Feeder... -
Page 8: Control Panel
6. CONTROL PANEL To change the mode from cold to hot or oppositely. Temperature TEMP. for hot mode on upper roller is max To reverse the rollers, press and hold the button. Speed Rotate the knob to control the roller’s speed from 0 to 6m/min. Run/Stop To start or stop the rollers. -
Page 9: Using Foot Pedal
Repeat to stop the rollers. 8. LOADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). Loading laminate to the upper film shaft: Remove the upper film supply shaft from the laminator and load the laminate through the film shaft. -
Page 10: Laminting
9.1. Laminating 1. Turn the power switch on (“I” position). The power switch is located on the rear left side of the unit. 2. Complete the steps as in the “LOADING FILM” section. 3. Load the roll of material to be laminated onto the bottom film supply shaft. Center with the laminate on the upper film shaft by using the centering markers supplied on the film shaft. -
Page 11: Troubleshooting
Fremont 65H Removing Adhesive Build Up 1. Remove the film from the laminator. 2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the silicone rollers and any other surfaces. Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface. -
Page 12: Specifications
13. SPECIFICATIONS Description Fremont 65H Power Supply AC100V,120V,220~240V,50/60Hz Power Consumption 1450W Maximum Laminating Width 65"(1650mm) Maximum Material Diameter(Film) Ø200mm Maximum Laminating Speed 6m/min Ready Time <40min Heating Method Hot Roller Maximum Temperature 122°F(50°C) Film Core 3" Auto Grip Roller Nip (Max) -
Page 13: Warranty
14. WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months.