Royal Sovereign Sigmont 65H Owner's Manual

Royal Sovereign Sigmont 65H Owner's Manual

Graphic lamination products

Advertisement

Owner's Manual
Sigmont 65H
GRAPHIC LAMINATION
PRODUCTS
Please read and retain these instructions.
To register your product, please go to www.royalsovereign.com
www.royalsovereign.com
Royal Sovereign International Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sigmont 65H and is the answer not in the manual?

Questions and answers

Summary of Contents for Royal Sovereign Sigmont 65H

  • Page 1 Owner's Manual Sigmont 65H GRAPHIC LAMINATION PRODUCTS Please read and retain these instructions. To register your product, please go to www.royalsovereign.com www.royalsovereign.com Royal Sovereign International Inc.
  • Page 2: Table Of Contents

    CONTENTS 1. Introduction 2. Safety Precautions 4. Installation 5. Control Panel 6. Product Identification 7. Using Foot Pedal And Remote Control 8. Loading Film 9. Threading Film 9.1 Laminating 9.2 Mounting 10. Adjusting the space of rollers 11. Maintenance 12. Troubleshooting 13.
  • Page 3: Introduction

    Graphic Lamination Products Model Sigmont 65H 1. IN TRODUCTION Thank you for choosing a Royal Sovereign laminator. It has been designed and manufactured to provide years of continuous service. For complete operating and maintenance information please read this manual thoroughly. Upon receipt of your laminator, please inspect the box, the machine and all other contents for shipping damage.
  • Page 4: Safety Precautions

    7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing. 8. Keep out of reach of children. 9. Only Royal Sovereign authorized maintenance and service technicians should make repairs. 10. Do not attempt to laminate items that exceed total recommended material thickness for the unit.
  • Page 5: Installation

    Once the laminator is in place, lock the casters into position. Always unlock the casters when moving to a different location. ELECTRICAL REQUIREMENTS Royal Sovereign recommends that a licensed electrician ensures proper power installation to your laminator in accordance with electrical codes in your area.
  • Page 6: Control Panel

    Sigmont 65H GRAPHIC LAMINATION PRODUCTS Please read and retain these instructions. To register your product, please go to www.royalsovereign.com www.royalsovereign.com Royal Sovereign International Inc. dust cover space silicon elastic Spare Main Power Fuse - FUSE(65TS) 10A/20A 5. CONTROL PANEL Rotate the knob to control the roller’s speed from 0 to 15m/min.
  • Page 7: Product Identification

    Sigmont 65H 6. PRODUCT IDENTIFICATION Shaft Release Liner Foot Switch Handle Tension Shaft Feeder Emergency Switch Knob Speed Control Roller Button Safety Sensor Nip Adjustment Wheel Table Front Wired Remote Controller Locking Caster...
  • Page 8: Using Foot Pedal And Remote Control

    2. PRESS STOP – To stop the rollers from turning. 3. PRESS FWD – To activate the rollers. 8. LOADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). Loading laminate to the upper film shaft: Remove the upper film supply shaft from the laminator and load the laminate through the film shaft.
  • Page 9: Laminating

    Sigmont 65H 9.1. Laminating 1. Turn the power switch on (“I” position). The power switch is located on the rear left side of the unit. 2. Complete the steps as in the “LOADING FILM” section. 3. Load the roll of material to be laminated onto the bottom film supply shaft. Center with the laminate on the upper film shaft by using the centering markers supplied on the film shaft.
  • Page 10: Troubleshooting

    Removing Adhesive Build Up 1. Remove the film from the laminator. 2. 2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the silicone rollers and any other surfaces. Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface. Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers.
  • Page 11: Specifications

    Sigmont 65H 13. SPECIFICATIONS Description Sigmont 65H Power Supply AC100V,120V,220~240V,50/60Hz Power Consumption 1600W Maximum Laminating Width 61"(1560mm) Maximum Material Diameter(Film) Ø150mm Maximum Laminating Speed 49.2ft/min (15m/min) Heating Method Hot Roller Maximum Temperature 140°F(60°C) Film Core 3" Auto Grip Roller Nip (Max) 1 inch (25.4mm)
  • Page 12: Warranty

    14. WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months.

Table of Contents

Save PDF