Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DeviceWell HDS9110
Summary of Contents for DeviceWell HDS9110
- Page 1 Users’ Manual SWITCHER Model: HDS9110 VER 1.0...
-
Page 2: Precautions
HDS9110 Precautions About this device: Copyright: ●This device belongs to the When using this unit for video and/or audio switching, publishing over the Internet, or the high-frequency video processing like, in some cases it may be necessary to equipment. Therefore, please strictly... -
Page 3: Table Of Contents
HDS9110 Contents Precautions ..........................2 Overview ........................... 6 Product Introduction ................... 6 Function Features ......................7 Preparation Before Installation ..................8 Equipment Unpacking ....................... 9 Size: 420*305*100mm ..................9 Interface Specification ..................... 10 Interface Introduction ..................10 TALLY Interface ....................12 Interface Parameters .................. - Page 4 HDS9110 T-bar Calibration ....................22 7.3.1 Panels Enable PGM and PVW Channel Selection ........... 24 7.3.2 Transition control ..................... 25 7.3.3 PGM Output Black Field .................. 25 7.3.4 USB Media Playback ..................26 7.3.5 SD card recording ..................... 27 7.3.6 Audio Settings ....................
- Page 5 HDS9110 Chroma KEY ....................40 7.5.8 7.5.8.1 Panel color image ..................40 System Menu Settings ..................41 System Setting ....................42 7.6.1 Network Setting ....................42 7.6.2 Recording Settings .................... 42 7.6.3 Device Info....................... 43 7.6.4 Failure and Maintenance....................44 Common Faults and Solutions ................
-
Page 6: Overview
Devicewell 10-channel switcher HDS9110 is an 8-channel SDI, 2-channel HDMI and 2-channel U-disk playback input video signal, a total of 6 SDI output, 3 HDMI output broadcast-level video signals. -
Page 7: Function Features
HDS9110 2. Function Features The DeviceWell Switcher is a multi-function switcher that requires no special knowledge and can be used for video switching and audio mixing with a simple operation. This unit can be used in radio and television, live broadcast and various activities. -
Page 8: Preparation Before Installation
HDS9110 3. Preparation Before Installation Caution ●During transportation, handling, and installation of switchboard equipment, avoid collisions between the switchgear equipment and doors, walls, shelves, etc. ●When the equipment is unpacked and transported, it is strictly forbidden to put it down and drag it gently to avoid damage to the switchboard equipment. -
Page 9: Equipment Unpacking
HDS9110 4. Equipment Unpacking When unpacking inspection, if the sealing label or packaging is found to be damaged, stop unpacking and report the situation to the equipment dealer. If the quantity of the goods is correct and the packaging is intact, the goods can be inspected. -
Page 10: Interface Specification
HDS9110 5. Interface Specification Interface Introduction HDS9110 interface is shown below. Definition Description TALLY DB-25 interface SDI IN 8-CH SDI input 3-way SDI video output PGM, SDI OUT1 custom output SDI OUT PGM/PVW, SDI OUT2 AUX auxiliary output AUDIO IN... - Page 11 HDS9110 Definition Description SD Card SD card recording PGM screen USB media player AUDIO Audio monitoring Website: www.devicewell.com Email: support@devicewell.cn...
-
Page 12: Tally Interface
HDS9110 5.2 TALLY Interface HDS9110 DB-25 Interface Definition Channel PGM（LED Red PVW (LED Green） GND:13 TALLY : Online schematic Note：Tally LED: for external display device Tally output : Active low (Tally LED is lit) High level is invalid (Tally out is off) Website: www.devicewell.com... -
Page 13: Interface Parameters
HDS9110 5.3 Interface Parameters Name Portable Switcher Model HDS9110 Input Signal SDI/HDMI Video Signal Rate 270Mbps~3Gbps Connector Standard Reflection loss >15dB 5MHz~3GHz Signal amplitude 800mV± 10%(SDI /HDMI) 100Ω (HDMI) 75Ω(SDI) Impedance Video Signal Input Balance Adaptive input HDMI 480i/576i,480p/576p,720p,1080i,1080p support... -
Page 14: Control Panel And Interface
In addition to the innovation of the enclosure, the DeviceWell HD switcher has also been completely optimized for the interface connector. Environmentally friendly materials with new RoHS standards are more demanding in terms of durability and environmental protection, providing customers with more stable, cost-effective and environmentally friendly products. -
Page 15: Button Description
6.1.2.2 Knob and LCD menu HDS9110 integrated LCD menu, can be set by knob The LCD menu is mainly divided into status display and menu settings. The knob control menu is divided into 3 states: 1. -
Page 16: Usb Media Play Area
HDS9110 6.1.2.3 USB Media Play Area USB1 and USB2 in the multimedia play area are control options, and USB1 is also controlled on USB1. VD/PIC is selected for video or picture, the default is to play video. Once pressed, you can switch to picture playback. -
Page 17: Camera Control Area
HDS9110 6.1.2.4 Camera Control Area Zoom in shooting distance Reduced shooting distance Push the camera rocker up: the lens is up Push the camera rocker down: the lens is down Push the camera rocker left: rotate the lens counterclockwise Push the camera rocker right: rotate the lens clockwise... -
Page 18: Integrated Control Area
HDS9110 After pressing this button, the screen will output color bars. 6.1.2.7 Integrated Control Area Auxiliary output, after accessing SDI OUT2, press AUX and press any one of the PVWs to assign one output to any of the 8 videos. -
Page 19: T-Bar
HDS9110 6.1.2.8 T-bar The switcher T-Bar system consists of a pusher module and an indicator light. Pushing the T-bar up can complete the transition. When the T-bar is pushed, the indicator light will follow the movement to the top 1 (the pusher pushes to the bottom and the top is a light). -
Page 20: Button Operation Instructions
HDS9110 7. Button Operation Instructions 7.1 Multi-Screen Output Window Introduction Preview and Program are preview and live output respectively; As shown below: There are 8 windows below that correspond to the input source monitoring, corresponding to the 1 - 8 buttons on the switchboard control panel. -
Page 21: Multi-Screen Preview 8 Channel Source Switching
HDS9110 7.2 Multi-screen preview 8 channel source switching 7.2.1 Panel realizes 10 screen split display and preview switching of 8 channel sources As shown above, how to change the input source of the 7th window and the 8th window: First press the SHIFT key on the control panel and then press 7/8 in the PVW, press once is SDI7 /... -
Page 22: Pgm&Pvw Switching
HDS9110 7.3 PGM&PVW Switching 7.3.1 T-bar Calibration When the switcher is in use, the fader misalignment may occur, and the origin of the switcher fader is offset. Therefore, the switcher pushrod system should be calibrated before use. First press the 1 and 2 buttons in the PGM area simultaneously with the device turned off. As shown below: Note: The 1 and 2 keys cannot be released during the calibration process. - Page 23 HDS9110 After the device is wired, input SDI camera 1 and camera 2, the default will be displayed in the red mark 1 and 2 position in the figure below; then press 1 and 2 respectively in the PGM and PVW areas of the control panel, then the PGM and PVW boxes above will display correspondingly.
-
Page 24: Panels Enable Pgm And Pvw Channel Selection
HDS9110 7.3.2 Panels Enable PGM and PVW Channel Selection The button board and the 1-8 channels in the PGM &PVW of the PC control software correspond to the 8 multi-screens under the 10-screen segmentation. Press the selection in the PGM area as shown above, and the button will turn red (live). Pressing PVW will display green (pre-supervised). -
Page 25: Transition Control
HDS9110 7.3.3 Transition control The transition control method of DeviceWell HDS9110 portable switcher is mainly divided into two types, one is transition special effect, and the other is transition mode without transition special effect. 1、 No transition effect: Press , CUT button is hard cut. If you select the preview (PVW) screen to switch directly to the main output (PGM), because there is no delay seamless switching, there is no transition effect. -
Page 26: Usb Media Playback
HDS9110 7.3.5 USB Media Playback Select the USB channel USB1 or USB2 to be controlled, and USB1 corresponds to the USB1 playback of the interface panel. Play video/picture selection keyboard: The default is to play video; if you want to play the picture, press this button to switch to picture playback. -
Page 27: Sd Card Recording
HDS9110 7.3.6 SD card recording You can use the SD card to record video. After inserting the SD card normally, press the REC button to record the PGM output video. To pause, you can click the PAUSE button Note: (Before using the SD card, format the SD card first, the SD card supports the FAT32/exFAT file format, and supports up to 128G SD card;... -
Page 28: Audio Settings
HDS9110 7.4 Audio Settings 7.4.1 Audio Introduction HDS9110 10-CH switcher has 1 XLR balanced audio input; 1 XLR balanced audio output. The audio mode is divided into mixing and following. 7.4.2 Audio Description 7.4.2.1 Audio Introduction HDS9110 switcher supports analog balanced audio input and output; supports SDI audio... -
Page 29: Audio Follow
7.4.2.6 Audio Monitoring The HDS9110 supports audio live monitoring. The 3.5mm standard headphones can be used to monitor the specified audio. By default, the PGM live video is monitored. By pressing the LISTEN on the mixer, you can monitor any audio. -
Page 30: Audio Usage Analysis
Audio usage analysis 7.4.3 The HDS9110 audio mode is divided into Follow and Mixing; Follow: The audio follows the video output to the PGM live broadcast, which means what the audio is coming in from the camera, and what is the audio output from the switcher live broadcast;... -
Page 31: Function Analysis Of The Mixer
HDS9110 2. The audio following channels are IN1-SDI1, IN2-SDI2, IN3-SDI3, IN4-SDI4, IN5-SDI5、IN6-SDI6、 IN7-SDI7（HDMI7） 、IN8-SDI8（HDMI8）,XLR_IN, corresponding operation panel buttons 7.4.3.3 Function analysis of the mixer According to the picture on the right: 1. CH1 means the first audio channel open key, and SRC1 means the source selection of the first audio channel;... -
Page 32: How To Use The Mix Assignment
HDS9110 7.4.3.4 How to use the mix assignment 1. Adjust the audio mode to Mixing by the knob first Corresponding to the status bar of the LCD screen, the audio channel source is displayed. The factory default is CH1 source IN1, CH2 source IN2, CH3 source IN3. - Page 33 HDS9110 3. Operate the mixer control area, press the SRC2 button to enter the second audio channel to select IN1, IN2, IN3, IN4, IN5, IN6, IN7、IN8、XLR_IN. The corresponding menu status bar will change according to your choice in real time.
-
Page 34: How To Listen To Audio
HDS9110 7.4.3.5 How to listen to audio Operate the mixer control area, press the LISTEN button to select the monitor source, and the corresponding menu status bar will change according to your choice in real time. The monitor source channel defaults to PGM. The channel selection of the monitor source is IN1, IN2, IN3, IN4, IN5, IN6, IN7、... -
Page 35: Fade In And Out Transition Effects
HDS9110 FADE In and Out Transition Effects 7.5.2 Select the effect control area and click to use the T-bar or AUTO to switch. FADE fades in and out, and A gradually darkens until it is completely black, and then gradually changes from black to B. -
Page 36: Inv Mirror Transition Effects
HDS9110 INV mirror transition effects 7.5.4 The INV mirror transition is opposite to the original WIPE transition. When you press WIPE and INV in the key panel, and then press the upward transition direction , the screen that appears will be the downward transition, and the effect diagram is shown below. -
Page 37: Pop Picture-Out-Picture Special Effect
HDS9110 Screen Select Horizontal Vertical Display Size Small Border Switch Border Width Border Color Green PIP size and position You can use the knob to set the parameters of the PIP picture-in-picture, as follows: Horizontal position setting: The value from the top left to the top right is 0-1280, and the value of each rotation knob is increased/decreased by 10. - Page 38 HDS9110 At this time, the information on the LCD screen will be switched to the POP picture-out-picture setting, and the knob can be set as required. As shown below Screen Select Horizontal Vertical Display Size Large Border Switch Border Width...
-
Page 39: Luma Key
HDS9110 Picture-out-picture source switching Press 1, 2, 3... in the PVW number keys to switch the input source of the picture. 7.5.7 Luma KEY The Luma key image supports the dynamic video source image and the static source image. The switcher will deduct the black part of the key source and retain other colors. -
Page 40: Chroma Key
HDS9110 luma key image information, as shown below. Luma BKGD Blue Grade Exit 7.5.8 Chroma KEY The chroma key image supports dynamic video source image and static source image, switching the opportunity to buckle the blue or green part of the key source, retaining other colors, and then overlapping the background image to achieve the purpose of image and overlay background. -
Page 41: System Menu Settings
HDS9110 When the chroma key is pressed, the LCD panel displays the current chroma key image information as shown below. Chroma BKGD Blue Grade Exit The video source item can select the key source, and the KEY type has the chroma key _ green and chroma key _ blue, and the level setting range is 0-64. -
Page 42: System Setting
HDS9110 Output resolution: Rotate the knob to operate, you can choose 1080p60 / 1080p50 / 1080p30 / 1080p25 / 1080p24 / 1080i50 / 1080i60 7.6.1 System Setting After turning the knob to the system setting, you can click the knob to enter the system setting... -
Page 43: Device Info
HDS9110 The level can be set in the recording settings, and can be set with low, middle, high and super high. 7.6.4 Device Info. Device Info. Software Version 0.0.0.0 Return Website: www.devicewell.com Email: support@devicewell.cn... -
Page 44: Failure And Maintenance
HDS9110 8. Failure and 8.1 Common Faults and Solutions (1) The output image may be flickered by interference. The quality of the wire used may be poor, and the shielding layer of the wire is not well prepared. When there is a strong radio near the use environment, radio waves may interfere with the transmission of the signal, resulting in unstable signal flicker.
Need help?
Do you have a question about the HDS9110 and is the answer not in the manual?
Questions and answers