Titan Advantage GPX 220 Owner's Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Water Pump
  5. Advantage GPX 220
  6. Owner's manual

Titan Advantage GPX 220 Owner's Manual

Gas piston pump
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
Do not use this equipment
before reading this manual!
ADVANTAGE GPX 220
Gas Piston Pump
Model Number:
0509023
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.
© Titan Tool Inc. All Rights Reserved. Form No. 0528903C
1011
•

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Advantage GPX 220 and is the answer not in the manual?

Questions and answers

Related Manuals for Titan Advantage GPX 220

Summary of Contents for Titan Advantage GPX 220

  • Page 1 Do not use this equipment before reading this manual! ADVANTAGE GPX 220 Gas Piston Pump Model Number: 0509023 NOTE: This manual contains important warnings and instructions. Please read and retain for reference. © Titan Tool Inc. All Rights Reserved. Form No. 0528903C 1011 •...

  • Page 2: Safety Precautions

    • Use lowest possible pressure to flush equipment. consultation with a plastic surgeon or reconstructive • Do not spray onto pump assembly. hand surgeon may be advisable. © Titan Tool Inc. All rights reserved.

  • Page 3: Specifications

    • Do not use the hose as a strength member to pull or lift the Power ........7.0 HP gas engine equipment. Weight ........164 lbs. (74.4 kg) • Do not lift by cart handle when loading or unloading. Maximum hose length ....300’ (91.4 m) © Titan Tool Inc. All rights reserved.

  • Page 4: Table Of Contents

    Safety Precautions section at the front of this a gasoline that contains alcohol, or one that you think contains alcohol, switch to a gasoline that manual before operating this equipment. you know does not contain alcohol. © Titan Tool Inc. All rights reserved.

  • Page 5: Setup

    Continue to hold the rope as you let it return. Pull and return the rope until the or tip guard installed. engine starts. 12. Move the PRIME/SPRAY valve to the SPRAY position. © Titan Tool Inc. All rights reserved.

  • Page 6: Painting

    NOTE: Turning the pressure up higher than needed to atomize the paint will cause premature tip wear and additional overspray. © Titan Tool Inc. All rights reserved.

  • Page 7: Pressure Relief Procedure

    If the pressure is set too low, tailing will appear or the paint will spatter out in gobs rather than in a fine spray. Paint tailing pattern Do not flex wrist while spraying. © Titan Tool Inc. All rights reserved.

  • Page 8: Cleanup

    15. Trigger the gun into the metal waste container until the 4. If you have any further questions concerning your TITAN paint is flushed out of the hose and solvent is coming out airless sprayer, call TITAN: of the gun.

  • Page 9: Maintaining The Engine

    • Make sure to use a spark plug wrench when installing and removing the plug. Gasket Filter Valve Housing Housing Assembly Valve Stem Valve Handle Dowel Pin Cam Base Groove Pin © Titan Tool Inc. All rights reserved.

  • Page 10: Replacing The Potentiometer

    Replacing the Sprayer ON/OFF Switch Electrostatic discharge (ESD) potential could cause Electrostatic discharge (ESD) potential could cause damage to electronic pressure control. use Titan damage to electronic pressure control. use Titan ESD wrist strap P/N 700-1037 or equivalent when ESD wrist strap P/N 700-1037 or equivalent when working on electronic pressure control.

  • Page 11: Replacing The Electronic Pressure Control (Epc) Assembly

    7. Install the four screws that secure the EPC assembly to Fluid the EPC housing. Tighten securely. Hose 8. Take the sprayer to a Titan Authorized Service Center for Fitting re-calibration. Replacing the Slider assembly and Slider Cart...

  • Page 12: Replacing The Gears

    18. Position the front cover over the pump housing. Secure damaged or worn. If the gear assembly is replaced, the front cover using the four front cover screws. replace the two thrust balls as well. © Titan Tool Inc. All rights reserved.

  • Page 13: Servicing The Clutch Assembly

    0.20" NOTE: a new clutch hub and armature assembly will come pre-assembled, but the “set back” will not be correct. The “set back” must still be created using the hub set-up tool. © Titan Tool Inc. All rights reserved.
  • Page 14 Electrostatic discharge (ESD) potential could cause 5. Line up the four holes around the outside of the clutch field damage to electronic pressure control. use Titan with the four set screw holes in the gear housing. The ESD wrist strap P/N 700-1037 or equivalent when clutch field wires should be at approximately the 1 or 2 working on electronic pressure control.

  • Page 15: Servicing The Fluid Section

    Procedure. Electrostatic discharge (ESD) potential could cause Before proceeding, follow the Pressure Relief damage to electronic pressure control. use Titan Procedure outlined previously in this manual. ESD wrist strap P/N 700-1037 or equivalent when additionally, follow all other warnings to reduce working on electronic pressure control.
  • Page 16 32. Apply blue Loctite #242 to the threads of the upper seal NOTE: Repacking kit P/N 0555222 is available. For best retainer. Thread the upper seal retainer into the cylinder results use all parts supplied in this kit. but do not tighten. © Titan Tool Inc. All rights reserved.

  • Page 17: Troubleshooting

    Turn the pressure control knob clockwise to supply power to the unit and increase the pressure setting. Faulty or loose wiring. Inspect or take to a Titan authorized service center. The gas tank is empty. Fill the gas tank. The unit will not prime.

  • Page 18: Français

    Se servir de la pression la plus basse possible pour vidanger s’avérer nécessaire de consulter un plasticien ou un spécialiste l’appareil. en chirurgie reconstructive de la main. • Ne pas pulvériser de produit sur la pompe. Français © Titan Tool Inc. Tous droits réservés.
  • Page 19 électrique de la prise avant de travailler sur l’équipement. • N’utilisez pas le tuyau pour tirer ou soulever l’équipement. • Ne pas soulever par la poignée de chariot en chargeant ou en déchargeant. © Titan Tool Inc. Tous droits réservés. Français...

  • Page 20: Español

    Use la presión más baja posible para enjuagar el equipo. consultar con un cirujano plástico o un cirujano especialista en • No rocíe el ensamblaje de la bomba. reconstrucción de las manos. Español © Titan Tool Inc. Todos los derechos reservados.
  • Page 21 • No utilice la manguera como elemento de fuerza para tirar del equipo o levantarlo. • No levantar por la manija del carro al cargar o descargando. © Titan Tool Inc. Todos los derechos reservados. Español...

  • Page 22: Parts Listings

    Screw ............4 0509553 Screw ............2 0509520 Connecting pin..........1 730-165 Grounding cable ........1 0509521 Retaining ring ...........1 0507785 Return hose (not shown) ......1 0555265A Fluid section assembly ......1 0507404 Hose, high pressure (not shown)....1 © Titan Tool Inc. All rights reserved.

  • Page 23: Drive Assembly

    Drive shaft assembly ........1 0555621 Engine ............1 0555902 Clutch field assembly........1 0509569 Hex screw ..........4 0507748 Cap ............1 0507786 Lock washer ..........4 NOTE: all electrical work should be performed by a Titan authorized service center. © Titan Tool Inc. All rights reserved.

  • Page 24: Fluid Section Assembly

    NOTE: When repacking the fluid section, make sure the raised lip on the bottom of the lower packing is fully outside the packing around the piston rod after insertion of the piston rod. © Titan Tool Inc. All rights reserved.

  • Page 25: Cart Assembly

    Plug, 3/8” ..........1 0509624 Wheel ............2 0508343 Outlet fitting, 3/8” x 3/8” ......1 812-003 Outlet fitting, 3/8” x 1/4” (optional) 0295697 Plug, 1/4” ..........1 0555625 Filter housing ..........1 0507690 PRIME/SPRAY valve assembly ....1 © Titan Tool Inc. All rights reserved.

  • Page 26: Prime/Spray Assembly

    5006543 Groove pin ..........1 0507662 Valve handle ..........1 Engine Labels Part # Description 0290803 Front cover label 0295840 Warning label, explosion 0295841 Warning label, injection 0295805 Shock hazard label 0509819 “No Oil” label © Titan Tool Inc. All rights reserved.

  • Page 27: Accessories

    G-10 XL Two Finger Spray Pack with 50” x 1/4” airless hose 550-100 S-5 Airless Spray Gun with 517 reversible tip 550-110 S-5 Spray Pack with 50’ x 1/4” airless hose 700-1037 Electrostatic discharge (ESD) wrist strap 9870307 Grease, 6 lb. can © Titan Tool Inc. All rights reserved.

  • Page 28: Limited Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s...

Table of Contents