Table of Contents

Advertisement

Quick Links

Downtown 300i ABS
By KWANG YANG Motor Co., Ltd.
1st Edition, Jan 2010
All rights reserved. Any reproduction or
unauthorized use without the written
permission of KWANG YANG Motor Co., Ltd.
is expressly prohibited.
T300-SK60AB-A2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Downtown 300i ABS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for KYMCO Downtown 300i ABS

  • Page 1 Downtown 300i ABS By KWANG YANG Motor Co., Ltd. 1st Edition, Jan 2010 All rights reserved. Any reproduction or unauthorized use without the written permission of KWANG YANG Motor Co., Ltd. is expressly prohibited. T300-SK60AB-A2...
  • Page 2: Table Of Contents

    Downtown 300i ABS PREFACE TABLE OF CONTENTS This Service Manual describes the technical features servicing GENERAL INFORMATION procedures KYMCO Downtown 300i ABS EXHAUST MUFFLER/FRAME COVERS Section 1 contains the precautions for all operations stated in this manual. INSPECTION/ADJUSTMENT Read them...
  • Page 3: General Information

    1. GENERAL INFORMATION Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ GENERAL INFORMATION ________________________________________________________________________________ SERIAL NUMBER ----------------------------------------------------------------------------------- 1-1 SPECIFICATION ------------------------------------------------------------------------------------ 1-2 SERVICE PRECAUTIONS ------------------------------------------------------------------------ 1-3 TORQUE VALUES ---------------------------------------------------------------------------------- 1-7 SPECIAL TOOLS ----------------------------------------------------------------------------------- 1-9 LUBRICATION POINTS ------------------------------------------------------------------------- 1-12 CABLE & HARNESS ROUTING ------------------------------------------------------------------ 1-13...
  • Page 4: General Information

    1. GENERAL INFORMATION Downtown 300i ABS SERIAL NUMBER Location of Frame Serial Number (inside luggage box) Location of Vehicle Identification Location of Engine Serial Number Number (VIN)
  • Page 5: Specification

    1. GENERAL INFORMATION Downtown 300i ABS SPECIFICATIONS Oil filter type Full-flow filtration Oil capacity 1.5 liter Name Downtown 300i ABS Exchanging capacity 1.3 liter Model No. SK60AB Fuel injection system Overall length 2200 mm Air cleaner type & No Paper element, wet...
  • Page 6: Service Precautions

    1. GENERAL INFORMATION Downtown 300i ABS  Apply or add designated greases and SERVICE PRECAUTIONS lubricants to the specified lubrication points.  Make sure to install new gaskets, O-rings, circlips, cotter pins, etc. when reassembling.  When two persons work together, pay attention to the mutual working safety.
  • Page 7 1. GENERAL INFORMATION Downtown 300i ABS  If the fuse is burned out, find the cause  Before connecting a terminal, check for and repair it. Replace it with a new one damaged terminal cover or loose negative according to the specified capacity.
  • Page 8 1. GENERAL INFORMATION Downtown 300i ABS  Protect wires and harnesses with electrical  Do not squeeze wires against the weld or tape or tube if they contact a sharp edge its clamp. or corner. Do not pull too tight!...
  • Page 9 1. GENERAL INFORMATION Downtown 300i ABS   Wire Symbols: harnesses routed along with following symbols represent the handlebar should not be pulled tight, have servicing methods and cautions included in excessive slack or interfere with adjacent this service manual.
  • Page 10: Torque Values

    1. GENERAL INFORMATION Downtown 300i ABS TORQUE VALUES...
  • Page 11 1. GENERAL INFORMATION Downtown 300i ABS TORQUE VALUES FRAME...
  • Page 12: Special Tools

    1. GENERAL INFORMATION Downtown 300i ABS SPECIAL TOOLS A120 E00003 FLYWHEEL PULLER M28X1 A120 E00012 TAPPET ADJUSTER OIL SEAL & BEARING A120 E00014 General size DRIVER BUSHING ABSORBER A120 E00019 O.D. 26 REMOVER A120 E00021 FLYWHEEL HOLDER A120 E00028 NUT & FITTING...
  • Page 13 1. GENERAL INFORMATION Downtown 300i ABS A120 E00048 FUEL PRESSURE GAUAGE VALVE COTTER A120 E00051 INSTALLER CLUTCH SPRING A120 E00053 COMPRESSOR A120 E00055 THREAD PROTECTOR 12mm/14 mm CRANKSHAFT BEARING A120 E00065 REMOVER 32143-LEA7-9000 INJECTOR CLEANER Keihin system A120 E00085 INJECTOR CLEANER...
  • Page 14 1. GENERAL INFORMATION Downtown 300i ABS A120 E00093 BEARING PULLER Lower/Upper Outer A120 F00009 Race Separator LOWER & UPPER A120 F00019 OUTER RACE INSTALLER STEERING STEM A120 F00023 TOP THREAD 39mm with longer WRENCH A120 F00031 PLIERS FUEL PIPE ELECTRIC REPAIR...
  • Page 15: Lubrication Points

    1. GENERAL INFORMATION Downtown 300i ABS LUBRICATION POINTS FRAME The following is the lubrication points for the frame. Use grease for parts not listed. Apply engine oil or grease to cables and movable parts not specified. It will avoid abnormal noise and damage the durability of the motorcycle.
  • Page 16: Cable & Harness Routing

    1. GENERAL INFORMATION Downtown 300i ABS CABLE & HARNESS ROUTING Tilt Switch Speedometer Radiator Filler Cap Lo Beam Relay Ignition Switch Hi Beam Relay Winker Relay Horn HYDRAULIC UNIT ABS ECU 1-13...
  • Page 17 1. GENERAL INFORMATION Downtown 300i ABS Throttle Body MAP Sensor Injector 1-14...
  • Page 18 1. GENERAL INFORMATION Downtown 300i ABS Ignition Coil Fuel Pump Relay Oil controller Output Voltage Connector Coolant Reserve Tank 1-15...
  • Page 19 1. GENERAL INFORMATION Downtown 300i ABS Starter Relay Regulator/Rectifier O2 Sensor 1-16...
  • Page 20: Troubleshooting

    1. GENERAL INFORMATION Downtown 300i ABS TROUBLESHOOTING ENGINE WILL NOT START OR IS HARD TO START Possible cause 1. Check for operation of the fuel pump Abnormal  Faulty fuel pump Normal 2. Inspect the fuel flow Abnormal  Faulty pressure regulator Normal 3.
  • Page 21 1. GENERAL INFORMATION Downtown 300i ABS ENGINE LACKS POWER Possible cause 1. Raise wheel off the ground Wheels do not  Brake dragging and spin by hand spin freely  Worn or damaged wheel bearing Wheel spins freely 2. Check tire pressure Pressure low ...
  • Page 22 1. GENERAL INFORMATION Downtown 300i ABS Possible cause 9. Check oil level and condition Incorrect  Oil level too high  Oil level too low  Contaminated oil Correct 10. Remove cylinder head cover Valve train not  Clogged oil...
  • Page 23 1. GENERAL INFORMATION Downtown 300i ABS POOR PERFORMANCE AT LOW AND IDLE SPEED Possible cause 1. Check ignition timing Incorrect  Improper ignition timing Correct 2. Inspect the fuel flow Abnormal  Faulty pressure regulator Normal 3. Inspect the fuel injector Abnormal ...
  • Page 24 1. GENERAL INFORMATION Downtown 300i ABS POOR PERFORMANCE AT HIGH SPEED Possible cause 1. Check ignition timing Incorrect  Faulty ECU Correct 2. Inspect the fuel flow Abnormal  Faulty pressure regulator Normal 3. Inspect the fuel injector Abnormal  Faulty injector Normal 4.
  • Page 25: Exhaust Muffler/Frame Covers

    . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ EXHAUST MUFFLER/FRAME COVERS __________________________________________________________________________________ SERVICE INFORMATION------------------------------------------------ 2- 1 TROUBLESHOOTING----------------------------------------------------- 2- 1 FASTENER REMOVAL AND REINSTALLATION------------------ 2- 2 FRAME COVERS REMOVAL/INSTALLATION --------------------- 2- 3 EXHAUST MUFFLER ----------------------------------------------------- 2-14...
  • Page 26: Exhaust Muffler/Frame Covers

    . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • When removing frame covers, use care not to pull them by force because the cover joint claws may be damaged. • Make sure to route cables and harnesses according to the Cable & Harness Routing.
  • Page 27: Fastener Removal And Reinstallation

    . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS FASTENER REMOVAL AND REINSTALLATION REMOVAL Depress the head of fastener center piece . Pull out the fastener. INSTALLATION Let the center piece stick out toward the head so that the pawls close. Insert the fastener into the installation hole.
  • Page 28: Frame Covers Removal/Installation

    . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS FRAME COVERS REMOVAL/ INSTALLATION SEAT Unlock the seat with the ignition key. Open the seat. Remove the two nuts and the seat. Installation is in the reverse order of removal. LUGGAGE BOX Unlock the seat with the ignition key.
  • Page 29 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS Center Cover CENTER COVER Remove the luggage box. Remove the center cover. * During removal, do not pull the joint claws forcedly to avoid damage. Installation is in the reverse order of removal.
  • Page 30 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS Installation is in the reverse order of removal. UPPER/LOWER HANDLEBAR COVER Remove the four screws and then remove upper handlebar cover. Remove the four screws, then remove the bottom handlebar cover. Disconnect the throttle cable refer to the “THROTTLE BODY /TPS”...
  • Page 31 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS WINDSHIELD/WINDSHIELD GARNISH Remove five bolts and windshield garnish.
  • Page 32 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS FRONT CENTER COVER Remove the windshield Remove four screws, then remove the front center cover. Remove the front cover. Installation is in the reverse order of removal. FRONT COVER Remove the small front cover(black) screw Remove the small front cover(black) Remove two nuts.
  • Page 33 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS Disconnect headlight/position light connector and right/left turn signal light connectors. Installation is in the reverse order of removal. FRONT FENDER Remove four screws attaching to the front fender. Installation is in the reverse order of removal.
  • Page 34 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS FRONT LOWER COVER Remove the front cover Remove the foot skirt Remove seven screws and front lower cover. Installation is in the reverse order of removal. REAR FENDER Remove the body cover and then the rear fender.
  • Page 35 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS Taillight Connector TIRE FENDER Remove the body cover. Remove four bolts attaching to the tire fender Installation is in the reverse order of removal. FLOORBOARD Remove the body cover Remove the right /left skirt Remove two screws.
  • Page 36 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS Remove eight bolts, then remove the floorboard. UNDER COVER Remove four bolts Remove the under cover. 2-11...
  • Page 37 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS Remove the fuel tank cap cover. Installation is in the reverse order of removal. Speedometer Wires METER PANEL Disconnect the speedometer wires. Disconnect the DC power connectors. DC power Connectors Remove one screws...
  • Page 38 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS INNER COVER Remove the front cover. Remove the front lower cover. Remove the floorboard Remove four bolts and front glove box one screw. Remove two fastener bolts, then remove the fuel tank fill cap.
  • Page 39: Exhaust Muffler

    . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS EXHAUST MUFFLER REMOVAL Disconnect the connector with O2 heater/O2 sensor. Nuts Remove the two exhaust pipe joint nuts Remove three muffler mount bolts and muffler and gasket. 2-14...
  • Page 40 . EXHAUST MUFFLER/FRAME COVERS Downtown 300i ABS INSTALLATION Replace the gasket with a new one. Install the exhaust muffler and three mounting bolt. Install and tighten the two exhaust pipe joint nuts to the specified torque Torque: 20 N•m (2 kgf•m,)
  • Page 41: Inspection/Adjustment

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ INSPECTION / ADJUSTMENT ________________________________________________________________________________ SERVICE INFORMATION----------------------------------------------------------------------- 3- 1 MAINTENANCE SCHEDULE------------------------------------------------------------------- 3- 2 THROTTLE OPERATION ----------------------------------------------------------------------- 3- 3 ENGINE OIL ---------------------------------------------------------------------------------------- 3- 4 RESERVE TANK ---------------------------------------------------------------------------------- 3- 5 AIR CLEANER ------------------------------------------------------------------------------------- 3- 6...
  • Page 42: Inspection/Adjustment

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS SERVICE INFORMATION GENERAL ! WARNING  Before running the engine, make sure that the working area is well ventilated. Never run the engine in a closed area. The exhaust contains poisonous carbon monoxide gas, which may cause death to people.
  • Page 43 3. INSPECTION/ADJUSTMENT Downtown 300i ABS...
  • Page 44: Throttle Operation

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS THROTTLE OPERATION Check the throttle grip for smooth movement. Measure the throttle grip free play. Free Play: 2~6 mm Major adjustment of the throttle grip free play is made with the adjusting nut at the throttle body side.
  • Page 45: Engine Oil

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS ENGINE OIL OIL LEVEL INSPECTION Stop the engine and support the scooter upright on the level ground. Wait for 2~3 minutes and check the oil level with the dipstick. Do not screw in the dipstick when checking the oil level.
  • Page 46: Reserve Tank

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS The spring will come out when the filter cap is removed. Let the engine oil drain out. Check that the O-ring is in good condition. Spring Install a new oil filter. * Make sure the rubber seal on the oil filter facing the left crankcase.
  • Page 47: Air Cleaner

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS AIR CLEANER AIR FILTER REPLACEMENT Remove the body cover. Remove seven screws attaching to the air cleaner cover. Remove six screws attaching to the filter. Check the filter and replace it if it is excessively dirty or damaged.
  • Page 48: Valve Clearance

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS Cylinder Head Cover VALVE CLEARANCE *  Inspect and adjust valve clearance while the engine is cold (below 35℃). Remove the seat assy and luggage box. Remove the four bolts and then cylinder head cover.
  • Page 49: Final Reduction Gear Oil

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS FINAL REDUCTION GEAR OIL *  Place the scooter on its main stand on level ground. Remove the transmission fluid drain bolt. Remove the transmission fluid filler bolt, then slowly rotate the rear wheel to drain the fluid.
  • Page 50: Brake System

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS BRAKE SYSTEM There is adjuster on each brake lever.Each adjuster has four positions so that the released lever position can be adjusted to suit the rider’s hands. To adjust the distance of the lever from the...
  • Page 51: Clutch Shoe Wear

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS CLUTCH SHOE WEAR Start engine and check the clutch operation by increasing the engine speed gradually. If the motorcycle tends to creep or the engine stop, check the clutch shoes for wear and replace if necessary.
  • Page 52: Nuts/Bolts/Fasteners

    3. INSPECTION/ADJUSTMENT Downtown 300i ABS NUTS/BOLTS/FASTENERS Check all important chassis nuts and bolts for looseness. Tighten them to their specified torque values if any looseness is found. WHEELS/TIRES Check the tires for cuts, imbedded nails or other damages. Check the tire pressure.
  • Page 53: Side Stand

    2. Put the side stand up and start the engine. 3. Lower the side stand. The engine should stop as you put the side stand down. * If the side stand system does not operate as described, see your KYMCO dealer for service. 3-12...
  • Page 54: Lubrication System

    4. LUBRICATION SYSTEM DOWNTOWN 300I ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ LUBRICATION SYSTEM ________________________________________________________________________________ LUBRICATION SYSTEM ------------------------------------------------------------------------ 4-1 SERVICE INFORMATION----------------------------------------------------------------------- 4-2 TROUBLESHOOTING --------------------------------------------------------------------------- 4-2 ENGINE OIL/OIL FILTER ----------------------------------------------------------------------- 4-3 OIL PUMP ------------------------------------------------------------------------------------------- 4-5...
  • Page 55: Lubrication System

    4. LUBRICATION SYSTEM DOWNTOWN 300I ABS LUBRICATION PART Dipstick Oil Filter Oil Pump Drive Chain...
  • Page 56: Service Information

    4. LUBRICATION SYSTEM DOWNTOWN 300I ABS SERVICE INFORMATION GENERAL INSTRUCTIONS  The maintenance of lubrication system can be performed with the engine installed on the frame.  Drain the coolant before starting any operations.  Carefully when removing and installing the oil pump not to allow dust and foreign matters to enter the engine and oil line.
  • Page 57: Engine Oil/Oil Filter

    4. LUBRICATION SYSTEM DOWNTOWN 300I ABS Oil Dipstick ENGINE OIL/OIL FILTER *  Place the scooter upright on level ground for engine oil level check.  Run the engine for 2~3 minutes and check the oil level after the engine is stopped for 2~3 minutes.
  • Page 58 4. LUBRICATION SYSTEM DOWNTOWN 300I ABS OIL FILTER REPLACEMENT Remove the oil filler cap attaching the right- under crankcase cover. Oil Filter Cap The spring will come out when the filter cap is removed. Let the engine oil drain out.
  • Page 59 4. LUBRICATION SYSTEM DOWNTOWN 300I ABS OIL PUMP REMOVAL Remove twelve bolts attaching the right crankcase cover. Remove the A.C. generator flywheel with special tool. Special tool: Flywheel Puller E003 Universal Holder E021 Starter Idle Gear Remove the gasket and dowel pins.
  • Page 60: Oil Pump

    4. LUBRICATION SYSTEM DOWNTOWN 300I ABS Arrow Mark Remove two oil pump mounting bolts and the oil pump. OIL PUMP INSTALLATION Install the oil pump into the crankcase. * Install the oil pump with the arrow on the pump body facing up and fill the oil pump with engine oil before installation.
  • Page 61: Engine Removal/Installation

    . ENGINE REMOVAL/INSTALLATION Downtown 300i ABS __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ ENGINE REMOVAL/INSTALLATION __________________________________________________________________________________ SERVICE INFORMATION------------------------------------------------ 5-1 ENGINE REMOVAL/INSTALLATION--------------------------------- 5-2 ENGINE HANGER --------------------------------------------------------- 5-6...
  • Page 62 5. ENGINE REMOVAL/INSTALLATION Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • A floor jack or other adjustable support is required to support and maneuver the engine. Be careful not to damage the scooter body, cables and wires during engine removal.
  • Page 63 . ENGINE REMOVAL/INSTALLATION Downtown 300i ABS ENGINE REMOVAL/INSTALLATION REMOVAL Remove the air cleaner Disconnect the connector including of ISC, Throttle body, TPS, WTS, MAP sensor and injector. Disconnect the O2 sensor connector. Disconnect the throttle cables. Disconnect Regulator/Rectifier connector. Fuel hose guide Disconnect the starter relay wire from starter motor.
  • Page 64 5. ENGINE REMOVAL/INSTALLATION Downtown 300i ABS Remove the muffler. Remove the rear fork mounting bolts (1) attaching to the crankcase. Torque: 3.5 kgf-m (35 N-m) Remove the rear axle nut (2). Torque: 12.0 kgf-m (120 N-m) Remove two bolts (3) attaching to rear brake hose clamps.
  • Page 65 . ENGINE REMOVAL/INSTALLATION Downtown 300i ABS Remove the spark plug cap. Spark Plug Cap Radiator Hose Disconnect the lower radiator hose from lower radiator pipe. Remove the right and left rear cushion lower mount bolts. Torque: 4.0 kgf-m (40N-m) Mount Bolt...
  • Page 66 5. ENGINE REMOVAL/INSTALLATION Downtown 300i ABS Remove the engine mount nut and pull it out. Remove the engine from the frame. * At removing the engine, be careful not to catch your hand or finger between the engine hanger and crankcase.
  • Page 67 . ENGINE REMOVAL/INSTALLATION Downtown 300i ABS ENGINE HANGER Mount Nut REMOVAL Remove the engine mount nut and pull it out. * Be careful to put the engine down. Remove the left/right engine hanger mount bolt. Remove the engine from frame.
  • Page 68: Cylinder Head/Valves

    6. CYLINDER HEAD/VALVES Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ CYLINDER HEAD/VALVES ________________________________________________________________________________ SCHEMATIC DRAWING------------------------------------------------------------------------- 6-1 SERVICE INFORMATION----------------------------------------------------------------------- 6- 2 TROUBLESHOOTING --------------------------------------------------------------------------- 6- 3 CYLINDER HEAD COVER REMOVAL ------------------------------------------------------ 6- 4 CAMSHAFT REMOVAL-------------------------------------------------------------------------- 6- 4 CYLINDER HEAD REMOVAL------------------------------------------------------------------ 6- 6...
  • Page 69: Schematic Drawing

    6. CYLINDER HEAD/VALVES Downtown 300i ABS SCHEMATIC DRAWING...
  • Page 70: Service Information

    6. CYLINDER HEAD/VALVES Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • The cylinder head can be serviced with the engine installed in the frame. Coolant in the radiator and water hoses must be drained. • When assembling, apply molybdenum disulfide grease or engine oil to the valve guide movable parts and valve arm sliding surfaces for initial lubrication.
  • Page 71: Troubleshooting

    6. CYLINDER HEAD/VALVES Downtown 300i ABS TROUBLESHOOTING • The poor cylinder head operation can be diagnosed by a compression test or by tracing engine top-end noises. Poor performance at idle speed White smoke from exhaust muffler • Compression too low •...
  • Page 72: Cylinder Head Cover Removal

    6. CYLINDER HEAD/VALVES Downtown 300i ABS Cylinder Head Cover CYLINDER HEAD COVER REMOVAL Remove the met-in box. Remove the body cover and center cover. Disconnect the breather hose to air cleaner. Remove the cylinder head cover four bolts. Remove the cylinder head cover.
  • Page 73 6. CYLINDER HEAD/VALVES Downtown 300i ABS Nuts Remove four nuts attaching to the cylinder head. Remove two bolts attaching to the camshaft gear. Remove the camshaft gear from the cam chain. * • Diagonally loosen the cylinder head cap nuts in 2 or 3 times.
  • Page 74: Cylinder Head Removal

    6. CYLINDER HEAD/VALVES Downtown 300i ABS Remove the rocker arm with bolt as shown. Rocker Arm CAMSHAFT INSPECTION Check each cam lobe for wear or damage. Check each camshaft bearing for play or damage. Replace the camshaft assembly with a new one if the bearings are noisy or have excessive play.
  • Page 75: Cylinder Head Disassembly

    6. CYLINDER HEAD/VALVES Downtown 300i ABS Remove nuts attaching upper/lower side of cylinder head. Remove two bolts attaching to the cylinder head. Remove the cylinder head. Remove the dowel pins and cylinder head gasket. Remove the cam chain guide. Bolts Remove all gasket material from the cylinder head mating surface.
  • Page 76: Cylinder Head Assembly

    6. CYLINDER HEAD/VALVES Downtown 300i ABS VALVE STEM INSPECTION Inspect each valve for bending, burning, or abnormal stem wear. Intake valve Exhaust valve Valves Remove carbon deposits from combustion chamber. Clean off any gasket remnants from the cylinder head contact surface.
  • Page 77: Cylinder Head Installation

    6. CYLINDER HEAD/VALVES Downtown 300i ABS CYLINDER HEAD INSTALLATION Dowel Pins Install the dowel pins and a new cylinder head gasket. Install the cam chain guide. * • Clean the intake valve rocker arm shaft grease before installation. Gasket Cam chain guide Cylinder Head Install the cylinder head.
  • Page 78 6. CYLINDER HEAD/VALVES Downtown 300i ABS Tighten the four cylinder head nuts and the Nuts four bolts between the cylinder head and cylinder. Torque: Cylinder head nuts: 3.6 kgf-m (35.3 N-m) Camshaft Gear Round hole Turn the A.C. generator flywheel so that the “T”...
  • Page 79: Cylinder Head Cover Installation

    6. CYLINDER HEAD/VALVES Downtown 300i ABS CYLINDER HEAD COVER INSTALLATION Adjust the valve clearance. Thermostat Injector Install a new cylinder head cover O-ring and install the cylinder head cover. * Be sure to install the O-ring into the groove properly.
  • Page 80: Cylinder/Piston

    7. CYLINDER/PISTON Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ CYLINDER/PISTON ________________________________________________________________________________ SCHEMATIC DRAWING------------------------------------------------------------------------- 7-1 SERVICE INFORMATION----------------------------------------------------------------------- 7-2 TROUBLESHOOTING --------------------------------------------------------------------------- 7-2 CYLINDER REMOVAL --------------------------------------------------------------------------- 7-3 PISTON REMOVAL ------------------------------------------------------------------------------- 7-3 PISTON INSTALLATION ------------------------------------------------------------------------ 7-7 CYLINDER INSTALLATION -------------------------------------------------------------------- 7-7...
  • Page 81: Schematic Drawing

    7. CYLINDER/PISTON Downtown 300i ABS SCHEMATIC DRAWING...
  • Page 82: Service Information

    7. CYLINDER/PISTON Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • The cylinder and piston can be serviced with the engine installed in the frame. • When installing the cylinder, use a new cylinder gasket and make sure that the dowel pins are correctly installed.
  • Page 83: Cylinder Removal

    7. CYLINDER/PISTON Downtown 300i ABS CYLINDER REMOVAL Cylinder Dowel Pins Remove the cylinder head. Remove the cam chain guide. Remove the cylinder. Water Hose Gasket Cam Chain Guide Remove the cylinder gasket and dowel pins. Clean any gasket material from the cylinder surface.
  • Page 84 7. CYLINDER/PISTON Downtown 300i ABS Inspect the piston, piston pin and piston rings. Remove the piston rings. * Take care not to damage or break the piston rings during removal. Clean carbon deposits from the piston ring grooves. Install the piston rings onto the piston and...
  • Page 85 7. CYLINDER/PISTON Downtown 300i ABS Measure the piston pin O.D. Service Limit: 16.994 mm replace if below Measure the piston O.D. * Take measurement at 9mm from the bottom and 90° to the piston pin hole. Service Limit: 72.70mm replace if below...
  • Page 86 7. CYLINDER/PISTON Downtown 300i ABS Measure the connecting rod small end I.D. Service Limit: 15.06 mm replace if over PISTON RING INSTALLATION Install the piston rings onto the piston. Apply engine oil to each piston ring. * • Be careful not to damage the piston and piston rings during assembly.
  • Page 87: Piston Installation

    7. CYLINDER/PISTON Downtown 300i ABS PISTON INSTALLATION Remove any gasket material from the crankcase surface. * • Be careful not to drop foreign matters into the crankcase. Install the piston, piston pin and a new piston pin clip. * • Position the piston “IN” mark on the intake valve side.
  • Page 88 7. CYLINDER/PISTON Downtown 300i ABS Install the cam chain guide. Gasket Dowel Pin * • Insert the tab on the cam chain guide into the cylinder groove. Install the cylinder head gasket and dowel Cam Chain Guide pins. Connect the water hose to the cylinder.
  • Page 89: Drive And Driven Pulleys/V- Belt

    8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS SCHEMATIC DRAWING...
  • Page 90 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • The drive pulley, clutch and driven pulley can be serviced with the engine installed. • Avoid getting grease and oil on the drive belt and pulley faces. Remove any oil or grease from them to minimize the slipping of drive belt and drive pulley.
  • Page 91 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS LEFT CRANKCASE COVER REMOVAL Remove the met-in box and carrier. Remove the body cover, center cover and rear fender A together. Remove the protector cover of left crankcase cover. Remove the bolts attaching to the left crankcase cover.
  • Page 92 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS INSPECTION Check the drive belt for cracks, separation or abnormal or excessive wear. Replace a new belt at every 20,000km. * • Use specified genuine parts replacement. MOVABLE DRIVE FACE ASSEMBLY Remove the pulley face, clutch outer, driven pulley and belt.
  • Page 93 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS INSPECTION Check each weight roller for wear or damage. Check the movable drive face bushing for wear or damage. ASSEMBLY...
  • Page 94 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS Install the weight rollers into the movable drive face. * • The direction of all weight rolls is same. The color side is towards to clockwise. Ramp Plate Install the ramp plate.
  • Page 95 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS Clutch Spring Compressor CLUTCH/DRIVEN PULLEY DISASSEMBLY Hold the clutch/driven pulley assembly with the clutch spring compressor. Set the tool in a vise and remove the clutch drive plate nut. * • Be sure to use a clutch spring compressor to avoid spring damage.
  • Page 96 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS INSPECTION Measure the driven face spring free length. Service Limit: 136 mm replace if below Outer Bearing DRIVEN PULLEY FACE BEARING REPLACEMENT Check the bearings for play and replace them if they have excessive play.
  • Page 97 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS Press a new needle bearing into the driven face. Clips Retainer Plate CLUTCH DISASSEMBLY Remove the clips and retainer plate to disassemble the clutch. * • Keep grease off the clutch linings.
  • Page 98 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS CLUTCH ASSEMBLY Clips Install the damper rubbers on the drive plate pins. Install the clutch weights/shoes and clutch springs onto the drive plate. Install the retainer plate and secure with the clips.
  • Page 99 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS Install the movable driven face onto the driven face. Grooves Apply grease to the guide rollers and guide roller pins and then install them into the holes of the driven face.
  • Page 100 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS INSTALLATION Install the movable drive face assembly and drive pulley collar onto the crankshaft. Drive Pulley Collar Movable Drive Face Assembly Movable Drive Face Assembly Put the drive belt on the driven pulley.
  • Page 101 8. DRIVE AND DRIVEN PULLEYS/ V-BELT Downtown 300i ABS Install the left crankcase cover. Left Crankcase Cover 8-13...
  • Page 102: Final Reduction

    9. FINAL REDUCTION Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ FINAL REDUCTION ________________________________________________________________________________ SCHEMATIC DRAWING------------------------------------------------------------------------- 9-1 SERVICE INFORMATION----------------------------------------------------------------------- 9-2 TROUBLESHOOTING --------------------------------------------------------------------------- 9-2 FINAL REDUCTION DISASSEMBLY -------------------------------------------------------- 9-3 FINAL REDUCTION INSPECTION ----------------------------------------------------------- 9-3 FINAL REDUCTION ASSEMBLY ------------------------------------------------------------- 9-5...
  • Page 103: Schematic Drawing

    9. FINAL REDUCTION Downtown 300i ABS SCHEMATIC DRAWING...
  • Page 104: Service Information

    9. FINAL REDUCTION Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • The servicing operations of this section can be made with the engine installed. • When replacing the drive shaft, use a special tool to hold the bearing inner race for this operation.
  • Page 105: Final Reduction Inspection

    9. FINAL REDUCTION Downtown 300i ABS FINAL REDUCTION DISASSEMBLY Remove the exhaust muffler. Remove the rear brake caliper. Remove the right rear shock absorber. Remove the rear fork. Remove the rear wheel. Remove the left crankcase cover. Remove the clutch outer/driven pulleys.
  • Page 106: Final Reduction Assembly

    9. FINAL REDUCTION Downtown 300i ABS Drive Shaft Bearing Inspect the final gear and final shaft for wear, damage or seizure. Drive Shaft Check the left crankcase bearings for Drive Shaft Bearing excessive play and inspect the oil seal for wear or damage.
  • Page 107 9. FINAL REDUCTION Downtown 300i ABS Dowel Pin FINAL REDUCTION ASSEMBLY Install the drive shaft into the left crankcase. Put the final gear on the left crankcase. Install the countershaft and gear into the left crankcase. Install the final shaft into the final gear and transmission case.
  • Page 108: Generator/Starter Clutch

    10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ A.C. GENERATOR/STARTER CLUTCH ________________________________________________________________________________ SCHEMATIC DRAWING------------------------------------------------------------------------- 10-1 SERVICE INFORMATION----------------------------------------------------------------------- 10-2 TROUBLESHOOTING --------------------------------------------------------------------------- 10-2 RIGHT CRANKCASE COVER REMOVAL-------------------------------------------------- 10-3 STATOR REMOVAL ------------------------------------------------------------------------------ 10-3 FLYWHEEL REMOVAL -------------------------------------------------------------------------- 10-4 STARTER CLUTCH ------------------------------------------------------------------------------ 10-4...
  • Page 109: Schematic Drawing

    10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS SCHEMATIC DRAWING 10-1...
  • Page 110: Service Information

    10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • All operations and inspections in this section can be made with the engine installed. • Should drain the coolant before removing the right crankcase cover. • Be careful not to drain the coolant when the engine temperature is high. (Perform this operation when the engine is cold.)
  • Page 111: Right Crankcase Cover Removal

    10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS RIGHT CRANKCASE COVER REMOVAL Disconnect the water hoses from the water pump cover. Disconnect the water hoses from the right crankcase cover. Remove bolts attaching right crankcase cover and the cover. Water Hose...
  • Page 112: Flywheel Removal

    10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS Flywheel FLYWHEEL REMOVAL Hold the flywheel with a flywheel holder and remove the flywheel nut and washer. Special Flywheel holder E021 Flywheel Holder Remove the flywheel with a flywheel puller. Special Flywheel puller...
  • Page 113 10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS Oil Separator Cover OIL PUMP REMOVAL Remove the attaching bolts and oil separator cover. Bolts Oil Pump Drive chain Cam Chain Spread the clip off and remove the oil pump driven gear, then remove the oil pump drive chain.
  • Page 114 10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS INSPECTION Inspect the starter driven gear for wear or damage. Measure the starter driven gear I.D. and O.D. I.D. Service Limits: I.D.: 22.15mm replace if over O.D.: 41.50mm replace if below O.D. Starter Idle Gear Inspect the starter idle gear and shaft for wear or damage.
  • Page 115 10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS Arrow Mark Bolts Cam Chain INSTALLATION Install oil pump and tighten two bolts. Make sure that the pump shaft rotates freely. The arrow of oil pump is upside. Install cam chain. Oil pump...
  • Page 116: Flywheel Installation

    10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS Starter Idle Gear Shaft Install the starter idle gear and shaft. Install the starter driven gear onto the crankshaft. Starter Driven Gear Flywheel FLYWHEEL INSTALLATION Install the flywheel onto the crankshaft by aligning the key on the crankshaft with the groove in the flywheel.
  • Page 117: Stator Installation

    10. A.C. GENERATOR/STARTER CLUTCH Downtown 300i ABS STATOR INSTALLATION Install the A.C. generator stator on the right Screws crankcase cover and secure it with the three bolts. Install the pulsar coil on the right crankcase cover and secure it with the two screws.
  • Page 118: Crankcase/Crankshaft

    11. CRANKCASE/CRANKSHAFT Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ CRANKCASE/CRANKSHAFT ________________________________________________________________________________ SCHEMATIC DRAWING------------------------------------------------------------------------- 11-1 SERVICE INFORMATION----------------------------------------------------------------------- 11-2 TROUBLESHOOTING --------------------------------------------------------------------------- 11-2 CRANKCASE SEPARATION------------------------------------------------------------------- 11-3 CRANKSHAFT INSPECTION ------------------------------------------------------------------ 11-4 CRANKCASE ASSEMBLY ---------------------------------------------------------------------- 11-5 11-0...
  • Page 119: Schematic Drawing

    11. CRANKCASE/CRANKSHAFT Downtown 300i ABS SCHEMATIC DRAWING 11-1...
  • Page 120: Service Information

    11. CRANKCASE/CRANKSHAFT Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • This section covers crankcase separation to service the crankshaft. The engine must be removed for this operation. • When separating the crankcase, never use a driver to knock the crankcase forcedly to prevent damaging the mating surfaces.
  • Page 121: Crankcase Separation

    11. CRANKCASE/CRANKSHAFT Downtown 300i ABS CRANKCASE SEPARATION Remove bolts attaching left crankcase. Place the crankcase with the left crankcase down and remove the right crankcase from the left crankcase. * • Never use a driver to knock the crankcase mating surfaces apart.
  • Page 122: Crankshaft Inspection

    11. CRANKCASE/CRANKSHAFT Downtown 300i ABS Oil Seal Remove the oil seal from the left crankcase. CRANKSHAFT INSPECTION Measure the connecting rod big end side clearance. Service Limit: 0.6 mm replace if over Measure the connecting rod small end I.D. Service Limit: 17.06 mm replace if over Measure the crankshaft bearing play.
  • Page 123: Crankcase Assembly

    11. CRANKCASE/CRANKSHAFT Downtown 300i ABS CRANKCASE ASSEMBLY Left Crankcase Install a new oil seal onto the left crankcase. Place the left crankcase down and install the crankshaft into the left crankcase. * • Avoid damaging the oil seal. • Apply grease to the lip of the oil seal.
  • Page 124: Cooling System

    12. COOLING SYSTEM Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ COOLING SYSTEM ________________________________________________________________________________ SCHEMATIC DRAWING------------------------------------------------------------------------- 12- SERVICE INFORMATION----------------------------------------------------------------------- 12- TROUBLESHOOTING --------------------------------------------------------------------------- 12- COOLING SYSTEM TESTING----------------------------------------------------------------- 12- RADIATOR ------------------------------------------------------------------------------------------ 12- WATER PUMP ------------------------------------------------------------------------------------- 12- 8 THERMOSENSOR -------------------------------------------------------------------------------- 12- 11 THERMOSTAT ------------------------------------------------------------------------------------- 12- 12...
  • Page 125: Schematic Drawing

    12. COOLING SYSTEM Downtown 300i ABS SCHEMATIC DRAWING 12-1...
  • Page 126: Service Information

    12. COOLING SYSTEM Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • The water pump must be serviced after removing the engine. Other cooling system service can be done with the engine installed in the frame. • The engine must be cool before servicing the cooling system.
  • Page 127 945cc 774cc * • Use coolant of specified mixing rate. (The mixing rate of 860cc KYMCO SIGMA coolant concentrate + 859cc distilled water is 50%.) • Do not mix coolant concentrate of different brands. • Do not drink the coolant, which is poisonous.
  • Page 128: Radiator

    12. COOLING SYSTEM Downtown 300i ABS COOLING SYSTEM TESTING Radiator Tester RADIATOR CAP INSPECTION Install the radiator cap onto the radiator tester and apply specified pressure to it. It must hold specified pressure for at least six seconds. * Apply water to the sealing cap surface before testing.
  • Page 129 12. COOLING SYSTEM Downtown 300i ABS Outlet Tube of Reserve Tank Inspect the radiator soldered joints and seams for leaks. Blow dirt out from between core fins with compressed air. If insects are clogging the radiator, wash them off. Carefully straighten any bent fins.
  • Page 130 12. COOLING SYSTEM Downtown 300i ABS Bolts/nuts Remove three bolts/nuts on the radiator. Remove the radiator. Bolts RADIATOR DISASSEMBLY Remove three bolts and then remove the fan rubber from the radiator. Check fan motor by battery. 12-6...
  • Page 131 12. COOLING SYSTEM Downtown 300i ABS THERMOSTATIC SWITCH Thermostatic Switch When the coolant temperature is lower than 85 ℃, the thermostatic switch OFF. When coolant temperature is over 90 ℃, the thermostatic switch ON. RADIATOR INSTALLATION Air Vent Tube Install the fan rubber on the radiator with three bolts.
  • Page 132: Water Pump

    12. COOLING SYSTEM Downtown 300i ABS Water Pump Right Crankcase Cover WATER PUMP MECHANICAL SEAL (WATER SEAL) INSPECTION Inspect the telltale hole for signs of mechanical seal coolant leakage. If the mechanical seal is leaking, remove the right crankcase cover and replace the mechanical seal.
  • Page 133 12. COOLING SYSTEM Downtown 300i ABS Water Pump Shaft WATER PUMP SHAFT REMOVAL Disconnect the water hose from the right crankcase cover. Remove bolts attaching the right crankcase cover. Remove the water pump bearing snap ring from the water pump assembly.
  • Page 134 12. COOLING SYSTEM Downtown 300i ABS Seal Washer (Porcelain) Install the dowel pins and a new gasket and Impeller then install the water pump assembly to the right crankcase cover. Tighten 12 bolts to secure the right crankcase cover. *...
  • Page 135: Thermosensor

    12. COOLING SYSTEM Downtown 300i ABS Thermosensor Wire THERMOSENSOR THERMOSENSOR REMOVAL Remove the met-in box and carrier. Remove the body cover, center cover and rear fender cover A. Drain the coolant. Disconnect the thermosensor wire. Remove the thermosensor. Thermosensor THERMOSENSOR INSPECTION...
  • Page 136: Thermostat

    12. COOLING SYSTEM Downtown 300i ABS THERMOSTAT THERMOSTAT REMOVAL Remove the met-in box and carrier. Remove the body cover, center cover and rear fender cover A. Drain the coolant. Disconnect the thermosensor wire from the thermosensor. Disconnect the water hose from the thermostat housing.
  • Page 137: Fuel Injection System

    13. FUEL INJECTION SYSTEM Downtown 300i ABS __________________________________________________________________________________ __________________________________________________________________________________ FUEL INJECTION SYSTEM __________________________________________________________________________________ SERVICE INFORMATION ------------------------------------------------ 13- 1 SPECIFICATIONS ---------------------------------------------------------- 13- 2 INJECTION SYSTEM DIAGRAM --------------------------------------- 13- 3 PARTS LOCATION -------------------------------------------------------- 13- 4 TROUBLESHOOTING ----------------------------------------------------- 13- 6 SELF-DIAGNOSTIC PROCEDURES WITHOUT...
  • Page 138: Fuel Injection System

    13. FUEL INJECTION SYSTEM Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS ● Scooter services can be done with the engine installed in the frame. ● Be sure to relieve the fuel pressure before fuel pump or fuel hose removal. ● Bending or twisting the control cables will affect operation and could cause the cables to stick or bind, resulting in loss of vehicle control.
  • Page 139: Specifications

    13. FUEL INJECTION SYSTEM Downtown 300i ABS SPECIFICATIONS ITEM SPECIFICATIONS Throttle body identification number LEA7 Idle speed 1600±100 rpm Throttle grip free play 2~6 mm (1/16~1/4 in) Fuel injector resistance (at 20°C/68°F) 11.7±0.6Ω 1100±33 Ω Fuel pump resistance Float at full position Float at empty position 100±3 Ω...
  • Page 140: Injection System Diagram

    13. FUEL INJECTION SYSTEM Downtown 300i ABS INJECTION SYSTEM DIAGRAM FULL NAME ABBREVIATIONS (01) Electronic control unit (02) Tilt switch (Angle detect sensor) ROLL (03) Fuel pump/Fuel level unit (04) Water temperature sensor WTS sensor (05) Crank position sensor (Pulser)
  • Page 141: Parts Location

    13. FUEL INJECTION SYSTEM Downtown 300i ABS PARTS LOCATION Tilt switch Speedometer Radiator filler cap Lo beam relay Hi beam relay Ignition switch Winker relay Horn Throttle body MAP sensor Injector 13-4...
  • Page 142 13. FUEL INJECTION SYSTEM Downtown 300i ABS Ignition coil Fuel pump replay Oil controller Output voltage connector Coolant reserve tank Starter relay Regulator/Rectifier O2 sensor 13-5...
  • Page 143: Troubleshooting

    13. FUEL INJECTION SYSTEM Downtown 300i ABS TROUBLESHOOTING Engine fail to start Backfiring or misfiring during acceleration • Intake manifold air leak • Ignition system malfunction • Fuel contaminated/deteriorated • Pinched or clogged fuel hose • Faulty fuel pump • Clogged fuel filter, throttle body •...
  • Page 144: Self-Diagnostic Procedures Without Diagnostic Tool

    13. FUEL INJECTION SYSTEM Downtown 300i ABS SELF-DIAGNOSTIC PROCEDURES WITHOUT DIAGNOSTIC TOOL SELF-DIAGNOSTIC PROCEDURES * It can be performed without diagnostics program. Place the scooter on its main stand. Put the side stand up and the engine stop switch is at “RUN”.
  • Page 145: Efi Self-Diagnosis Check Engine Lamp (Celp) Failure Codes

    13. FUEL INJECTION SYSTEM Downtown 300i ABS EFI SELF-DIAGNOSIS CHECK ENGINE LAMP (CELP) FAILURE CODES If more than a damaged part has occurred, the “CELP” begins blinking in order. The “CELP” denotes the failure codes. When the indicator lights for one second that For example: If the indicator blinks six times, is equal to ten.
  • Page 146: Self-Diagnosis Reset Procedure

    13. FUEL INJECTION SYSTEM Downtown 300i ABS SELF-DIAGNOSIS RESET PROCEDURE 1. Put the side stand up and engine stop switch is at “RUN”. 2. Turn the key to the ON position and wait for ten seconds. 3. Fully open the throttle and wait for ten seconds.
  • Page 147 13. FUEL INJECTION SYSTEM Downtown 300i ABS CELP FAILURE CODES LIST Failure Codes Blinks Contents Causes Symptoms (diagnostic tool) ● Faulty TPS voltage range (0.3~4.5 V) ● Loose or poor connection on TPS Engine operates Sensor P0120 Faulty TPS normally ●...
  • Page 148 13. FUEL INJECTION SYSTEM Downtown 300i ABS Failure Codes Blinks Contents Causes Symptoms (diagnostic tool) ● Faulty Inductive ignition coil Ω range (4.2 Ω ± 15%) Faulty ● Loose or poor connection on Engine fail to be inductive P0351 inductive ignition coil...
  • Page 149 13. FUEL INJECTION SYSTEM Downtown 300i ABS SPARK PLUG ANTI-FLOOD When have not failure code occurs and pressing starter switch repeatedly, can still not start the engine, maybe the spark plug is wet by fuel, perform the spark plug anti- flood to purge the fuel in the engine.
  • Page 150: Tps/Isc Reset

    13. FUEL INJECTION SYSTEM Downtown 300i ABS TPS/ISC RESET ● If close or open the throttle grip randomly, the ECU may record the incorrect TPS when the ECU or the throttle body has been reinstalled. It can cause hard to start engine or idling speed is not smooth when engine installation.
  • Page 151: Fuel Pump

    13. FUEL INJECTION SYSTEM Downtown 300i ABS FUEL PUMP INSPECTIION Full Position Put the side stand up and the engine stop switch is at “RUN” Disconnect fuel pump/fuel unit connector. Connect the multimeter (+) probe to the Red/Black terminal and the multi-meter (-) probe to the Green terminal.
  • Page 152 13. FUEL INJECTION SYSTEM Downtown 300i ABS Hose band Fuel Pump Connector REMOVAL Disconnect the connector and fuel band from the fuel pump. Remove the six screws onto the fuel pump. Remove the fuel pump and O-ring. Screw Connector INSTALLATION Replace a new O-ring on the fuel tank.
  • Page 153: Fuel Cut-Off Relay

    13. FUEL INJECTION SYSTEM Downtown 300i ABS Battery FUEL CUT-OFF RELAY INSPECTION Remove the fuel cut-off relay. Connect the ohmmeter to the fuel cut-off relay connector terminals. Connection: Black – Red/Black Connect 12 V battery with the fuel cut-off Fuel Cut-Off Relay relay connector.
  • Page 154: Tilt Switch

    13. FUEL INJECTION SYSTEM Downtown 300i ABS TILT SWITCH INSPECTION Support the scooter level surface. Put the side stand up and engine stop switch is at “RUN”. Turn the ignition switch to “OFF” Remove the screws, washers and tilt switch.
  • Page 155: Electronic Control Unit (Ecu)

    13. FUEL INJECTION SYSTEM Downtown 300i ABS ELECTRIC CONTROL UNIT (ECU) REMOVAL/INSTALLATION * ● Do not disconnect or connect the ECU connector during the ignition switch “ON”; it may cause the ECU damaged. ● The throttle position sensor (TPS) and...
  • Page 156 13. FUEL INJECTION SYSTEM Downtown 300i ABS INSPECTION Disconnect and remove the ECU from the frame. Check for continuity between pin 35 and 36 of the ECU side connector. There should be continuity at all times. Check for continuity between each pins 8, 9 and 24 of the ECU side connector.
  • Page 157: Fuel Injector

    13. FUEL INJECTION SYSTEM Downtown 300i ABS FUEL INJECTOR INSPECTION Disconnect the fuel injector connector. Measure the resistance between 2 pins of the fuel injector connector. Standard: 11.7±0.6 Ω (at 20°C/68°F) REMOVAL Disconnect the connector from the fuel injector. Remove the bolt of the fuel injector.
  • Page 158 13. FUEL INJECTION SYSTEM Downtown 300i ABS Groove INSTALLATION Apply the engine oil to a new O-ring. Install the fuel injector into the fuel pipe. Ensure the tab of the fuel injector inserted into the groove of the fuel pipe.
  • Page 159: Wts Sensor

    13. FUEL INJECTION SYSTEM Downtown 300i ABS WTS SENSOR (Water Temperature Sensor) REMOVAL / INSTALLATION Drain the coolant from the cooling system. Disconnect the WTS sensor connector from the sensor. Remove the WTS sensor and O-ring. Install a new O-ring and WTS sensor.
  • Page 160: O 2 Sensor

    13. FUEL INJECTION SYSTEM Downtown 300i ABS SENSOR The O sensor issues signal to ECU when the temperature is over 350°C during the engine is working. The temperature is up to 350°C earlier than the muffler for O heater sensor. So the O sensor begins performance.
  • Page 161: Throttle Body/Map/Isc/Tps

    ● Do not damage the throttle body, it may cause the throttle and idle valve isn’t synchronization. ● The throttle body is preset in KYMCO factory, do not disassemble it by a wrong way. ● Do not loosen or tighten the painted bolts and screws for the throttle body.
  • Page 162 13. FUEL INJECTION SYSTEM Downtown 300i ABS TPS INSPECTION Support the scooter on a level surface. Put the side stand up and engine stop switch is at “RUN”. Turn the ignition switch to “ON”. Measure if the ECU voltage outputs to TPS between the following terminals of the TPS connector.
  • Page 163 13. FUEL INJECTION SYSTEM Downtown 300i ABS Screw/Set Plate DISASSEMBLY * The throttle position sensor (TPS) and idle air bypass valve (ISC) have to be reset when the throttle body MAP, TPS, ISC or ECU has been reinstalled. Remove the screw and then remove the ISC and set plate.
  • Page 164: Diagnostic Tool Connector

    13. FUEL INJECTION SYSTEM Downtown 300i ABS Apply oil onto a new O-ring. When install the MAP onto the throttle body, being careful not to damage the O-ring. * Always replace an O-ring with a new one. Install the set plate and tighten the screw securely.
  • Page 165 13. FUEL INJECTION SYSTEM Downtown 300i ABS FI DIAGNOSTIC TOOL OPERATION INSTRUCTIONS 3620A-LEB2-E00 13-28...
  • Page 166 13. FUEL INJECTION SYSTEM Downtown 300i ABS 一. FI DIAGNOSTIC TOOL This tool is developed by KYMCO and for KYMCO vehicle only. Please refer to the specification when serving this vehicle. This tool is without battery inside. The power is provided from vehicle.
  • Page 167 13. FUEL INJECTION SYSTEM Downtown 300i ABS 二. DTC INSPECTION PROCEDURE Showing four functions on the screen when switching on power. LEA7 is for Downtown 300i A). ECU version: Including of model name, ECU number, identifications number and software version.
  • Page 168 13. FUEL INJECTION SYSTEM Downtown 300i ABS B). Press the " Down " button and then turn to the first page. LEA7 is for Downtown 300i C). Press the " Enter " button to check the DTC failure code LEA7 is for...
  • Page 169 13. FUEL INJECTION SYSTEM Downtown 300i ABS D). Press the " Enter " button E). Press the " Enter " button F). Display what's DTC number on this DTC-List. Press the " Enter " button and then turn to the previous page...
  • Page 170 5. FUEL INJECTION SYSTEM Downtown 300i ABS G). Press the " UP " button H). Press the " Enter " button and then turn to the previous page with red color. I). Press the " UP " button 5-33...
  • Page 171 5. FUEL INJECTION SYSTEM Downtown 300i ABS J). Press the " Enter " button and then turn to the first page. LEA7 is for Downtown 300i LEA7 is for Downtown 300i 5-34...
  • Page 172 5. FUEL INJECTION SYSTEM Downtown 300i ABS 三. DTC CLEAR PROCEDURE ). Check the DTC LEA7 is for Downtown 300i ). Press the " Enter " button LEA7 is for Downtown 300i ). Choose " Load DTC " Press the " Down " button...
  • Page 173 5. FUEL INJECTION SYSTEM Downtown 300i ABS ). Press the " Enter " button and the indicator is lighting. ). Clearing DTC completed if the indicator is off. 5-36...
  • Page 174 5. FUEL INJECTION SYSTEM Downtown 300i ABS 四. DATA ANALYSIS PROCEDURE ). Press the " Down " twice LEA7 is for Downtown 300i ). Choose “ Data Analyze” Press the " Enter " button to enter page 01 LEA7 is for Downtown 300i ).
  • Page 175 5. FUEL INJECTION SYSTEM Downtown 300i ABS ). Down-page 02 The measure figures including of TPS position, Intake pressure and Intake air temperature. Press the “ Down” button to enter page 03. ). Down-page 03 The measure figures including of Atmosphere pressure, Fuel Injector interval and Ignition advance timing.
  • Page 176 5. FUEL INJECTION SYSTEM Downtown 300i ABS ). Down-page 05 The measure figures including of ISC target, ISC step and ISC learn step. Press the “ Down” button to enter page 06. ). Down-page 06 The measure figures including of ISC motor state.
  • Page 177: Vehicle Can Not Be Started

    5. FUEL INJECTION SYSTEM Downtown 300i ABS 五. Vehicle can not be started – Handling method (Steps) Preliminary Checking: 6 basic inspection 1. Is the battery with voltage (12 V or higher) 2. Key-On and listen for any action with Fuel Pump / Fuel Pump Relay (It will turn off automatically in 5-10 seconds) 3.
  • Page 178: Manual Trouble Shooting Procedure

    5. FUEL INJECTION SYSTEM Downtown 300i ABS 六. Manual Trouble Shooting Procedure How to read DTC from speedometer? New Phase 5 Fuel Injection Engine Vehicle DTC Reading: Automatic indication – ECU upgrade version (with Oxygen sensor): Reading DTC from speedometer directly.
  • Page 179: Diagnostic Report

    5. FUEL INJECTION SYSTEM Downtown 300i ABS DIAGNOSTIC REPORT D o w n to w n 3 0 0 i D e a le r : C u s to m e r : E n g . N o :...
  • Page 180 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM __________________________________________________________________________________ SERVICE INFORMATION------------------------------------------------ 14- 1 TROUBLESHOOTING----------------------------------------------------- 14- 2 HANDLEBAR --------------------------------------------------------------- 14- 3 FRONT WHEEL------------------------------------------------------------- 14- 6 FRONT BRAKE FLUID---------------------------------------------------- 14- 9...
  • Page 181 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • Remove the motorcycle frame covers before removing the front wheel, steering handlebar, front shock absorber and front fork. Jack the motorcycle front wheel off the ground and be careful to prevent the motorcycle from falling down.
  • Page 182 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM TROUBLESHOOTING Hard steering (heavy) Front wheel wobbling • Excessively tightened steering stem top • Bent rim • Loose front axle cone race • Broken steering balls • Bent spoke plate • Insufficient tire pressure •...
  • Page 183 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS HANDLEBAR REMOVAL Remove the lower handlebar cover and front cover. Remove two bolts and disconnect the brake light switch wire, then remove the rear brake master cylinder. Remove the two bolts and disconnect the brake light switch wire, then remove the front brake master cylinder.
  • Page 184 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM Install the front and rear master cylinders and connect the brake light switch wires. DISASSEMBLY Remove two screws attaching to the right handlebar switch. Screws Throttle cable Disconnect the throttle cable from the throttle grip.
  • Page 185 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS Remove two screws and then remove the left handlebar switch. ASSEMBLY Screws Install the left handlebar switch. * Align the pin on the left handlebar switch with the hole on the handlebar.
  • Page 186: Steering Handlebar/Front Wheel/Front Brake/Front

    14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM FRONT WHEEL REMOVAL Jack the scooter front wheel off the ground. Remove the bolt and then pull out the axle. Remove the front wheel and collar. Bolt AXLE RUNOUT INSPECTION Set the axle in V blocks and measure the runout using a dial gauge.
  • Page 187 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS Collar INSTALLATION Apply grease to the collar, then install the collar onto the wheel. Dust Seal Install the speedometer speed wheel sensor. DISASSEMBLY Remove the side collar and dust seal.
  • Page 188 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM Remove the front wheel bearing by using the Bearing special tool. Special tool: Bearing puller E00037 ASSEMBLY Install the front wheel bearing by using the special tool. Special tool: Bearing installer E00014 Install the distance collar.
  • Page 189 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS FRONT BRAKE FLUID FLUID REPLACEMENT/AIR BLEEDING * ● A contaminated brake disc or pad reduces stopping power. Discard contaminated pads clean contaminated disc with a high quality brake degreasing agent.
  • Page 190 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM Loosen the bleed valve and apply the brake lever. Stop operating the brake when no more fluid flows out of the bleed valve. BRAKE FLUID FILLING/AIR BLEEDING * Do not mix different types of fluid since they are not compatible.
  • Page 191 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS If the brake bleeder is not available, perform the following procedure. Pump up the system pressure with the brake lever until these are not air bubbles in the fluid flowing out of the reservoir small hole and lever resistance is felt.
  • Page 192 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM FRONT BRAKE PAD BRAKE PAD REPLACEMENT Remove the pad pins. Remove the two caliper mounting bolts, then remove the caliper. Bolts Pad Pins Brake Pads Remove the brake pads. * Always replace the brake pads in pairs to ensure even disc pressure.
  • Page 193 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS Install new pads so that their ends rest on the pad retainer on the brake properly. Install the pad pin by pushing the pads against the pad spring to align the pad pin holes in the pads and caliper.
  • Page 194 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM FRONT SHOCK ABSORBER REMOVAL Remove the front cover and front fender. Remove the front brake caliper Remove the front wheel Remove the speed wheel sensor bolt and then remove the brake hose guide from right front shock absorber.
  • Page 195 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS STEERING STEM REMOVAL Remove the steering handlebar. Remove the front brake hose and speed wheel sensor connector from the guide. Right Hold the steering stem top cone race and remove the steering stem lock nut by using the special tool.
  • Page 196 14.HANDLEBAR/FRONT WHEEL/FRONTBRAKE/ Downtown 300i ABS FRONT SHOCK ABSORBER/STEERING STEM Ball Inspect the ball races, cone races and steel balls for wear or damage. Replace if necessary. Remove the top balls. Remove the upper ball race by using a chisel if necessary.
  • Page 197 14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/ FRONT SHOCK ABSORBER/STEERING STEM Downtown 300i ABS INSTALLATION Install the new bottom cone race onto the steering stem. Install the new upper and bottom ball races into the frame. Apply grease to the top and bottom ball races and install new steel balls on the top ball race and new steel balls on the bottom ball race.
  • Page 198: Rear Brake/Rear Fork/Rear

    15. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER Downtown 300i ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ REAR BRAKE/REAR FORK/REAR WHEEL/ REAR SHOCK ABSORBER _________________________________________________________________________________________ SCHEMATIC DRAWING ------------------------------------------------------------------------- 15-1 SERVICE INFORMATION ----------------------------------------------------------------------- 15-2 TROUBLESHOOTING ---------------------------------------------------------------------------- 15-2 REAR BRAKE--------------------------------------------------------------------------------------- 15-3 REAR FORK----------------------------------------------------------------------------------------- 15-6...
  • Page 199 15. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER Downtown 300i ABS SCHEMATIC DRAWING 15-1...
  • Page 200 15. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • When performing the services stated in this section, the engine and exhaust muffler must be cold to avoid scalding. • During servicing, keep oil or grease off the brake pads and brake disk.
  • Page 201 15. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER Downtown 300i ABS REAR BRAKE Brake Fluid Tube Bolt Brake Caliper REAR BRAKE CALIPER REMOVAL First remove the exhaust muffler. Remove the rear brake fluid tube bolt and disconnect the brake fluid tube.
  • Page 202 . REAR WHEEL/REAR BRAKE/ REAR SUSPENSION Downtown 300i ABS Compressed Air Remove the piston from the brake caliper. If necessary, use compressed air to squeeze out the piston through the brake fluid inlet opening and place a towel under the caliper to avoid contamination caused by the removed piston.
  • Page 203 . REAR WHEEL/REAR BRAKE/ REAR SUSPENSION Downtown 300i ABS * Make sure the spring plate next to the brake pad dowel pin orientation. Install two brake pads. Brake Pads INSTALLATION Brake Fluid Tube Bolt Caliper Install the brake caliper to the rear fork and tighten the two bolts.
  • Page 204 . REAR WHEEL/REAR BRAKE/ REAR SUSPENSION Downtown 300i ABS REAR FORK REMOVAL Remove the exhaust muffler. Remove the rear brake caliper. Bear Axle Nut Bolt Remove the right rear shock absorber lower mount bolt. Remove the rear axle nut and remove the collar.
  • Page 205 . REAR WHEEL/REAR BRAKE/ REAR SUSPENSION Downtown 300i ABS REAR WHEEL REMOVAL Remove the exhaust muffler. Remove the rear brake caliper. Remove the rear fork. Remove the rear axle collar. Remove the rear wheel. Bear Axle Collar INSTALLATION The installation sequence is the reverse of removal.
  • Page 206 . REAR WHEEL/REAR BRAKE/ REAR SUSPENSION Downtown 300i ABS 15-8...
  • Page 207: Battery/Charging System

    . BATTERY/CHARGING SYSTEM Downtown 300i ABS __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ BATTERY/CHARGING SYSTEM __________________________________________________________________________________ CHARGING SYSTEM LAYOUT ---------------------------------------- 16-1 CHARGING CIRCUIT ----------------------------------------------------- 16-1 SERVICE INFORMATION------------------------------------------------ 16-2 TROUBLESHOOTING----------------------------------------------------- 16-3 BATTERY CHARGING --------------------------------------------------- 16-4 CHARGING SYSTEM ----------------------------------------------------- 16-6 REGULATOR/RECTIFIER ----------------------------------------------- 16-6 16-0...
  • Page 208: Battery/Charging System

    . BATTERY/CHARGING SYSTEM Downtown 300i ABS CHARGING SYSTEM LAYOUT BATTERY REGULATOR/RECTIFIER 16-1...
  • Page 209: Service Information

    . BATTERY/CHARGING SYSTEM Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS * The battery electrolyte (sulfuric acid) is poisonous and may seriously damage the skin and eyes. Avoid contact with skin, eyes, or clothing. In case of contact, flush with water and get prompt medical attention •...
  • Page 210: Troubleshooting

    . BATTERY/CHARGING SYSTEM Downtown 300i ABS TROUBLESHOOTING No power Intermittent power • Dead battery • Loose battery cable connection • Disconnected battery cable • Loose charging system connection • Fuse burned out • Loose connection or short circuit in • Faulty ignition switch...
  • Page 211 . BATTERY/CHARGING SYSTEM Downtown 300i ABS Screws BATTERY REMOVAL The battery is in the battery box below seat. 1. Remove the seat. 2. Remove the met-in box 3. Remove four screws and then the battery retainer. (+) Terminal (-) Terminal 4.
  • Page 212: Battery Charging

    . BATTERY/CHARGING SYSTEM Downtown 300i ABS BATTERY CHARGING Remove the battery Connect the charger positive (+) cable to the battery positive (+) terminal. Connect the charger negative (-) cable to the battery negative (-) terminal. * Turn the power ON/OFF at the charger, not at the battery terminals.
  • Page 213: Regulator/Rectifier

    . BATTERY/CHARGING SYSTEM Downtown 300i ABS REGULATOR/RECTIFIER WIRE HARNESS INSPECTION Remove the luggage box Disconnect the regulator/rectifier connectors. Check the connectors for loose contacts of corroded terminals. Regulator/Rectifier BATTERY WIRE Measure the voltage between the Red/White wire terminal and ground.
  • Page 214 . BATTERY/CHARGING SYSTEM Downtown 300i ABS CHARGING COIL WIRE Measure the resistance between each Yellow wire terminals. Standard: 0.4 ~ 0.6 Ω (20ºC/68ºF) Disconnect the regulator/rectifier connector. Check for continuity between each Yellow wire terminal regulator/rectifier side and ground. There should be no continuity.
  • Page 215: Ignition System

    17. IGNITION SYSTEM Downtown 300I ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ IGNITION SYSTEM ________________________________________________________________________________ IGNITION SYSTEM LAYOUT ------------------------------------------------------------------ 17-1 SERVICE INFORMATION----------------------------------------------------------------------- 17-2 TROUBLESHOOTING --------------------------------------------------------------------------- 17-2 SPARK PLUG -------------------------------------------------------------------------------------- 17-3 IGNITION COIL INSPECTION ----------------------------------------------------------------- 17-3 A.C. GENERATOR INSPECTION------------------------------------------------------------- 17-4 TILT SWITCH INSPECTION ------------------------------------------------------------------- 17-4...
  • Page 216 17. IGNITION SYSTEM Downtown 300I ABS IGNITION SYSTEM LAYOUT Tilt switch Ignition Coil Ignition Switch A.C. Generator Crank Position Sensor IGNITION CIRCUIT 17-1...
  • Page 217: Service Information

    17. IGNITION SYSTEM Downtown 300I ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • Some electrical components may be damaged if terminals or connectors are connected or disconnected while the ignition switch is “ON” and current is present. • When servicing the ignition system, always follow the steps in the troubleshooting on page 17-2.
  • Page 218: Spark Plug

    17. IGNITION SYSTEM Downtown 300I ABS Ignition Coil SPARK PLUG For spark plug inspection and adjustment, refer to page 3-5. IGNITION COIL INSPECTION Remove the seat and met-in box. ( 2-6) Remove the ignition coil. Primary Coil IGNITION COIL CONTINUITY...
  • Page 219: Generator Inspection

    17. IGNITION SYSTEM Downtown 300I ABS A .C. GENERATOR INSPECTION CRANK POSITION SENSOR INSPECTION * This test is performed with the stator installed in the engine. Remove the seat and met-in box. Disconnect the Crank Position Sensor Wire Coupler. Crank Position Sensor Wire Coupler...
  • Page 220 17. IGNITION SYSTEM Downtown 300I ABS REMOVAL/INSTALLATION Tilt Switch “UP” Mark Screws Disconnect the connector and remove two screws, then remove tilt switch. Installation is in the reverse order of removal. * Install the tilt switch with its “up” mark facing up.
  • Page 221: Starting System

    18. STARTING SYSTEM Downtown 300I ABS ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ STARTING SYSTEM ________________________________________________________________________________ STARTING SYSTEM LAYOUT ---------------------------------------------------------------- 18-1 SERVICE INFORMATION----------------------------------------------------------------------- 18-2 TROUBLESHOOTING --------------------------------------------------------------------------- 18-2 STARTER MOTOR-------------------------------------------------------------------------------- 18-3 STARTER RELAY INSPECTION-------------------------------------------------------------- 18-4 18-0...
  • Page 222 18. STARTING SYSTEM Downtown 300I ABS STARTING SYSTEM LAYOUT Starter Relay Ignition Switch STARTING CIRCUIT Relay 18-1...
  • Page 223 18. STARTING SYSTEM Downtown 300I ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • The removal of starter motor can be accomplished with the engine installed. • After the starter clutch is installed, be sure to add the engine oil and coolant and then bleed air from the cooling system.
  • Page 224 18. STARTING SYSTEM Downtown 300I ABS STARTER MOTOR REMOVAL * Before removing the starter motor, turn the ignition switch OFF and remove the battery ground. Then, turn on the ignition switch and push the starter button to make sure the starter motor can’t operate securely.
  • Page 225 18. STARTING SYSTEM Downtown 300I ABS Starter Motor Cable INSTALLATION Connect the starter motor cable. Check the O-ring for wear or damage and replace if necessary. Apply grease to the O-ring and install it to the starter motor. Tighten the two mounting bolts.
  • Page 226: Lights Switches/ Fuel Pump

    19. LIGHTS SWITCHES/ FUEL PUMP Downtown 300i ABS __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ LIGHTS/METERS/SWITCHES __________________________________________________________________________________ SERVICE INFORMATION------------------------------------------------ 19- 1 BULB REPLACEMENT --------------------------------------------------- 19- 2 BRAKE LIGHT SWITCH-------------------------------------------------- 19- 6 IGNITION SWITCH -------------------------------------------------------- 19- 6 HANDLEBAR SWITCH --------------------------------------------------- 19- 7 LUGGAGE BOX LIGHT SWITCH -------------------------------------- 19- 9...
  • Page 227 19. LIGHTS SWITCHES/ FUEL PUMP Downtown 300i ABS ELECTRICAL EQUIPMENT LAYOUT Radiator 19-1...
  • Page 228 19. LIGHTS SWITCHES/ FUEL PUMP Downtown 300i ABS SERVICE INFORMATION GENERAL * A halogen head light bulb becomes very hot while the head light is on, and remains for a while after it is turned off. Be sure to let it cool down before servicing.
  • Page 229 19. LIGHTS SWITCHES/ FUEL PUMP Downtown 300i ABS BULB REPLACEMENT LICENECE LIGHT Remove the seat assembly and luggage box. Remove the body covers. Disconnect the license bulb socket. Remove the bulb and replace with a new one. 19-3...
  • Page 230 19. LIGHTS/METERS/SWITCHES Downtown 300i ABS Connector Headlight Bulb HEADLIGHT * A halogen headlight bulb becomes hot while the headlight is ON and remains for a while after it is turned OFF. Be sure to let it cool down before servicing.
  • Page 231 19. LIGHTS/METERS/SWITCHES Downtown 300i ABS Put the headlight wires into the headlight unit Waterproof Rubber and then cover the waterproof rubber. Highlight wires Press the waterproof rubber around with hand until its seat. INSPECTION Confirm if the waterproof rubber is covered firmly.
  • Page 232 19. LIGHTS/METERS/SWITCHES Downtown 300i ABS FRONT TURN SIGNAL LIGHT Socket Remove the front cover. Turn the bulb socket, then remove the front turn signal light. Push and turn the bulb counterclockwise to remove it, then replace with a new one.
  • Page 233 19. LIGHTS/METERS/SWITCHES Downtown 300i ABS REAR TURN SIGNAL LIGHT Push and turn the bulb counterclockwise to remove it, then replace with a new one. Installation is in the reverse order of removal. Rear Turn Signal Light Taillight/Brake Light 19-7...
  • Page 234: Brake Light Switch

    19. LIGHTS/METERS/SWITCHES Downtown 300i ABS BRAKE LIGHT SWITCH Remove the upper handlebar cover. Disconnect front or rear brake light switch connectors and check for continuity between the switch terminals. There should be continuity with the front or rear brake lever squeezed, and there should be no continuity with the front or rear brake lever is released.
  • Page 236: Handlebar Switch

    19. LIGHTS/METERS/SWITCHES Downtown 300i ABS Dimmer Switch LEFT HANDLEBAR SWITCH INSPECTION Disconnect left handlebar switch connector and check for continuity at switch side connector terminals. Continuity should exist between the color code wires as follows: Horn Switch Turn Signal light Switch...
  • Page 237: Fuel Pump

    19. LIGHTS/METERS/SWITCHES Downtown 300i ABS Connector FUEL PUMP REMOVAL Remove the seat and met-in Remove the center cover Remove the fuel pump connector Be sure to relieve the fuel pressure before removing fuel pump or fuel hose. Remove the six nuts and fuel unit connectors then remove the fuel hose.
  • Page 238 19. LIGHTS/METERS/SWITCHES Downtown 300i ABS INSPECTION Connect the fuel unit wire connectors and turn the ignition switch “ON”. * Before performing the following test, operate the turn signals to determine that the battery circuit is normal. Measure resistance between Red/Black and Green wire of the fuel unit connector.
  • Page 239: Side Stand Switch

    19. LIGHTS/METERS/SWITCHES Downtown 300i ABS Connector SIDE STAND SWITCH INSPECTION Remove the luggage box. Side stand switch is located on side stand. Disconnect the side stand switch connector. There should be continuity between the Yellow/Green and Green with the side stand is up.
  • Page 240: Horn

    19. LIGHTS/METERS/SWITCHES Downtown 300i ABS HORN INSPECTION Remove the front cover. Disconnect the horn connectors from the horn. Connect a 12 V battery to the horn terminals. The horn is normal if it sounds when the 12 V battery is connected across the horn terminals.
  • Page 241: Evaporative Emission Control System

    EVAPORATIVE EMISSION CONTROL SYSTEM Downtown 300i ABS EVAPORATIVE EMISSION CONTROL SYSTEM SCHEMATIC DRAWING ---------------------------------------------------------- 20-1 EVAPORATIVE EMISSION CONTROL SYSTEM FUNCTION------------ 20-2 TROUBLESHOOTING-------------------------------------------------------------- 20-2 SERVICE INFORMATION -------------------------------------------------------- 20-3 PERGE CONTROL VALVE ------------------------------------------------------- 20-4 CHARCOAL CANISTER----------------------------------------------------------- 20-6 20-0...
  • Page 242: Schematic Drawing

    EVAPORATIVE EMISSION CONTROL SYSTEM Downtown 300i ABS SCHEMATIC DRAWING Air Cleaner Charcoal Canister/ Purge Control Valve Throttle Body Fuel Injector 20-1...
  • Page 243: Evaporative Emission Control System Function

    EVAPORATIVE EMISSION CONTROL SYSTEM Downtown 300i ABS EVAPORATIVE EMISSION CONTROL SYSTEM FUNCTION FOREWORD: The Evaporative Emission Control System is abbreviated to E.E.C. System. This device collects the fuel vapor from the fuel tank and then the fuel vapor is drawn into the engine for re-burning to avoid air pollution caused by the fuel vapor diffused into the air.
  • Page 244: Service Information

    EVAPORATIVE EMISSION CONTROL SYSTEM Downtown 300i ABS SERVICE INFORMATION GENERAL INSTRUCTIONS • Do not smoke or allow flames or sparks near the working area. • Note the locations of tubes for proper installation. • Replace any damaged tube with a new one.
  • Page 245 EVAPORATIVE EMISSION CONTROL SYSTEM Downtown 300i ABS Purge Control Valve To Throttle Body PURGE CONTROL VALVE REMOVAL 1. Remove the front cover. 2. Disconnect the purge control valve vacuum tube that goes to the throttle body and the tubes that go to the air cleaner and charcoal canister.
  • Page 246 EVAPORATIVE EMISSION CONTROL SYSTEM Downtown 300i ABS PURGE CONTROL VALVE FLOW INSPECTION 1. Connect a vacuum pump to the purge control valve vacuum tube and apply vacuum pressure of 45mm/Hg. 2. Connect a pressure pump to the tube that goes to the charcoal canister and apply Pressure Pump pressure.
  • Page 247: Charcoal Canister

    EVAPORATIVE EMISSION CONTROL SYSTEM Downtown 300i ABS Charcoal Canister To Throttle Body CHARCOAL CANISTER REMOVAL 1. Remove the front cover. 2. Disconnect the charcoal canister tubes that go to the fuel tank and purge control valve. 3. Remove the charcoal canister.
  • Page 248 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS ANTI-LOCK BRAKE SYSTEM (ABS) ABS Indicator Light---------------------------------------- --------- 21-01 ABS Introduction -------------------------------------------- --------- 21-02 ABS Parts Location ----------------------------------------- --------- 21-03 Wheel Speed ------------------------------------------------- --------- 21-04 ABS ECU & ABS Hydraulic Unit ------------------------ --------- 21-06 ABS ECU GUARANTEE---------------------------------- --------- 21-07...
  • Page 249 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS ABS Indicator Light The ABS indicator light in the meter position. This light will comes on when the ignition switch is turned on and goes off shortly after the vehicle starts moving at speed 6km/hr min. It stays off.
  • Page 250 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS ABS Introduction ABS is designed to help prevent the wheels from locking up when the brakes are applied hard while running straight. The ABS automatically regulates brake force. Intermittently gaining gripping force and braking force helps prevent wheel lock-up and allows stable steering control while stopping.
  • Page 251 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS Parts Location Front Wheel speed Sensor Front Wheel speed Sensor Rotor Front Wheel speed Sensor’s connector Front Wheel speed Sensor Rotor Rear Wheel speed Sensor Rear Wheel speed Sensor’s connector ABS ECU & ABS Hydraulic Unit...
  • Page 252 21. ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS WHEEL SENSOR Front Wheel Speed Sensor REMOVAL & INSPECTION Remove the front wheel speed sensor. Install the front wheel speed sensor. Front Wheel Speed Sensor Rotor Remove a bolt attaching to the front wheel speed sensor Front Wheel speed Sensor’s connector...
  • Page 253 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS Remove the rear wheel speed sensor. Front Wheel Speed Sensor Rotor Rear Wheel Speed Sensor Remove the connector of rear wheel speed sensor <Rear Wheel Speed Sensor> Rear Wheel speed Sensor’s connector ※ Standard clearance: 0.4-1.2mm...
  • Page 254 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS ABS ECU REMOVAL& INSTALLATION The coupler is used for automobile’s waterproof. Please take car of operation. Please keep a good ventilating about ECU in order to prevent the ABS ECU from high temperature.
  • Page 255 ABS ECU GUARANTEE: * Don’t remove four special bolts to take out the ABS ECU. If remove it during the guarantee period. KYMCO can not take a responsibility for it. Oil tube bolt 4 * 3.5 kgf-m ※ Don ’ t need to drain the brake fluid if replace a new ECU Hydraulic unit.
  • Page 256 DIAGNOSTIC TOOL OPERATION 1. Connect the KYMCO Fi Diagnostic tool 2. Put the side stand upward and ENG. stop switch is at “RUN” position. 3. Connect the diagnostic tool connector. (KYMCO Fi Diagnostic tool Power comes from vehicle’s Battery) Self-Diagnostic Tool Connector...
  • Page 257 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS 4. Choose Fi ECU Version and then push down button for three times. LEA7 5. Choose No.2 ABS SYS ECU and then push up button to previous. 6. Confirming ECU Version and then enter ABS system.
  • Page 258 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS 7. Choose ECU Version and then push “Enter” button. 8. Confirm ABS ECU Version if is LEA7-E00 1.1.1 9. Choose DTC Inspect 21-10...
  • Page 259 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS 10. Load DTC (Active 、Occurred、History) DTC DISPLAYED 1. Rear wheel speed sensor disconnect 2. Front wheel speed sensor disconnect 21-11...
  • Page 260 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS DTC CLEARED 1. Choose “Clear DTC” and then push “Enter” button. 2. Clearing DTC completed until the DTC red lamp is off. DATA ANALYZE 1. Choose “DATA Analyze” and then push “Enter” button...
  • Page 261 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS 2. Front wheel speed & Rear wheel speed & Battery volt Battery volt: Standard 9.6~16.7V KYMCO Diagnosis 01 Fr Speed 5 km/hr Re Speed 5 km/hr Battery Volt 12.6V * You can turn the front or rear wheel to check if the wheel speed is figured.
  • Page 262 ANTI-LOCK BRAKE SYSTEM (ABS) Downtown 300i ABS Bosch ABS8m DTC List Bosch ABS8m DTC LIST Code NO (Diagnostic description Tool ) (PDA) 3620A-LEB2- 5013 Rear Inlet Valve malfunction(EV) 5014 Rear Outlet Valve malfunction (AV) 5017 Front Inlet Valve malfunction (EV)

Table of Contents

Save PDF