Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crestron C2-AUDIO-6PAK
Summary of Contents for Crestron C2-AUDIO-6PAK
- Page 1 Crestron C2-AUDIO-6PAK Six-Zone Audio Package Reference Guide...
- Page 2 This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. 2003 Crestron Electronics, Inc.
-
Page 3: Table Of Contents
Audio Source Wiring... 6 Advanced Wiring ... 7 Software Setup... 8 Software System Requirements... 8 Installation via the Crestron Audio Six-Pack CD... 8 Installation of Crestron Application Builder ... 9 Three Step Configuration ... 9 System Operation... 18 On/Off Button... 18 Volume and Mute Buttons... -
Page 5: Six-Zone Audio Package: C2-Audio-6Pak
Six-Zone Audio Package: C2-AUDIO-6PAK Introduction The C2-AUDIO-6PAK, or Audio Six-Pack, is a complete package of 15 high- performance components plus programming software, all specially designed to work together. This packaged solution requires only minimal configuration and quick setup for a 6-zone audio distribution system. It is also an excellent way to start a basic system that is fully expandable for future upgrades. -
Page 6: Hardware Setup
Six-Zone Audio Package nomenclature of some components in the package. Throughout this guide, all references to C2-AUDIO-6PAK apply to the different user interface colors, type of control system, and their respective international versions as well, except where noted. The C2-AUDIO-6PAK is anchored by the Crestron 2-Series control system (CP2 or CP2E) and the CNAMPX-12x60 Multi-Channel Power Amplifier. - Page 7 Net IDs. However, the six keypads are zone specific. Be sure to install the given user interface into the appropriate room as defined in the Crestron Audio Six-Pack Wizard. Each keypad is physically labeled with the Net ID in the barcode label.
-
Page 8: Network Wiring
Network Wiring Refer to the network wiring diagram, shown below, when making all network connections between the hardware devices of the C2-AUDIO-6PAK. NOTE: Cresnet cable is not included with the C2-AUDIO-6PAK. It must be procured separately. KEYPAD CP2 or CP2E... - Page 9 Four-Wire Network Connector The four-wire network cable is used to provide power and communications with Crestron devices. Before making any four-wire network connections, refer to the following network interconnection diagram and the cautions that follow. Recommended Network Cable, Liberty Wire Reference: Cresnet...
-
Page 10: Audio Source Wiring
Six-Zone Audio Package CAT5 Wiring CAT5 wiring can also be used to connect Crestron devices. Before making any CAT5 connections, refer to the following network interconnection diagram and the cautions that follow. CAT5 Interconnect Drawing SPARES CAUTION: Possible equipment damage if miswired. -
Page 11: Advanced Wiring
C2-AUDIO-6PAK and the sources. Advanced Wiring If the intent is to use the C2-AUDIO-6PAK in a configuration other than its basic design, refer to the individual device Operations Guides when making these “advanced” wiring connections. -
Page 12: Software Setup
CP2 or CP2E processor. If a different processor is part of your system, use the Crestron AppBuilder after completing the steps in the Wizard to swap control systems. Refer to “Appendix A: Swapping Control Systems”... -
Page 13: Installation Of Crestron Application Builder
CP2 or CP2E processor. If a different processor is part of your system, use the Crestron AppBuilder after completing the steps in the Wizard to swap control systems. Refer to “Appendix A: Swapping Control Systems”... - Page 14 In the second field, enter a location to save all files that are created using the Wizard. Defaults for each field are shown below. Name the System 10 • Six-Zone Audio Package: C2-AUDIO-6PAK Crestron C2-AUDIO-6PAK Reference Guide – DOC. 8188B...
- Page 15 The Wizard has access to that have, at one time, been pro- either the Crestron or User Database. Make a choice by selecting the correct grammed into a Crestron system.
- Page 16 Configure button to modify how this device is connected to the control system. For example, a CD might automatically be assigned to port C of an IR card. To place 12 • Six-Zone Audio Package: C2-AUDIO-6PAK Crestron C2-AUDIO-6PAK Reference Guide – DOC. 8188B...
- Page 17 Click the New button to add a controller to the list assuming a valid controller is available. • Click the Remove button to remove the currently selected controller from the list. Some controllers (i.e., built-in cards) cannot be removed. Six-Zone Audio Package: C2-AUDIO-6PAK • 13 Six-Zone Audio Package...
- Page 18 Crestron AppBuilder solely. The C2-AUDIO-6PAK is designed to provide control from up to six locations. The Interfaces screen of the Wizard allows the user to assign source control from each of the six rooms. From the pull-down above the user interface on the screen, as shown after this paragraph, choose a room.
- Page 19 Crestron e-Control application’s help file for Ethernet / e-Control details. Also, review the latest version of the Crestron e-Control Reference Guide (Doc. 6052), which is available from the Downloads | Product Manuals section of the Crestron website (www.crestron.com).
- Page 20 Finish Screen NOTE: The CP2E can use TCP/IP as the Connection Type when uploading system programs. For uploading details, refer to the latest version of the Crestron e-Control Reference Guide (Doc. 6052), which is available from the Downloads | Product Manuals section of the Crestron website (www.crestron.com).
- Page 21 Crestron C2-AUDIO-6PAK The Audio Configuration button serves as a reminder that audio properties such as volume, bass, treble, and balance are set to Crestron default settings. Therefore, these properties need to be adjusted for personal preference. Refer to “Audio Configuration” on page 19 of this guide for details. Clicking on the button opens the help file to the Audio Configuration section.
-
Page 22: System Operation
Six-Zone Audio Package System Operation This section describes how to use the function keypad to operate a Crestron audio distribution system. NOTE: These keypads are standard Crestron network devices and as such do not have any functionality built-in. Instead, the program loaded into the CP2 governs their operation. -
Page 23: Source Selection And Control
Balance – 50 % (centered) source affects the volume of that source in all rooms. Audio properties such as Min Volume – 30% volume, bass, treble, and balance are set to Crestron default settings. Therefore, Max Volume – 70% Startup Volume – 35% these properties need to be adjusted for personal preference. -
Page 24: Setup Modes
The text that appears in this illustration for the 8 buttons at the top of the keypad does not actually appear on the button. 20 • Six-Zone Audio Package: C2-AUDIO-6PAK Crestron C2-AUDIO-6PAK • Enter Room Setup Mode: Momentarily press both Volume Up and Down buttons simultaneously to enter Room Setup Mode. -
Page 25: Source Setup Mode Operation
Mute Button: This button's LED blinks rapidly along with the On/Off button to indicate Source Setup Mode activity. • Volume Up/Down Buttons: Adjust the input compensation of the currently selected source. Six-Zone Audio Package: C2-AUDIO-6PAK • 21 Six-Zone Audio Package... -
Page 26: Problem Solving
Firmware Upgrades To take advantage of all the C2-AUDIO-6PAK features, it is important that the units that make up the pak contain the latest firmware available. Therefore, please check Crestron’s website (http://www.crestron.com/downloads/software_updates.asp) for... -
Page 27: Appendix A: Swapping Control Systems
Crestron C2-AUDIO-6PAK Appendix A: Swapping Control Systems NOTE: This appendix is intended for those using the Crestron Audio Six-Pack CD (v1.2) to program their audio system, which contains a control system other than the CP2 or CP2E. If your audio system physically contains a control system other than the CP2 or CP2E, you must swap control systems after finishing the three configuration steps. -
Page 28: Appendix B: Notice To Cnx-Audio-6Pak Users
If you have an existing CNX-AUDIO-6PAK system and wish to make changes to the system, a version of software is available to you from the Crestron Audio Six-Pack CD (version 1.1). Install the software as directed in “Installation via the Crestron Audio Six-Pack CD”... -
Page 29: Software License Agreement
This Agreement may only be modified by a writing signed by an authorized officer of Crestron. Updates may be licensed to You by Crestron with additional or different terms. This is the entire agreement between Crestron and You relating to the Software and it supersedes any prior representations, discussions, undertakings, communications or advertising relating to the Software. - Page 30 “applets” incorporated into the Software), the accompanying media and printed materials, and any copies of the Software are owned by Crestron or its suppliers. The Software is protected by copyright laws and international treaty provisions. Therefore, you must treat the Software like any other copyrighted material, subject to the provisions of this Agreement.
-
Page 31: Return And Warranty Policies
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. - Page 32 Crestron Electronics, Inc. Reference Guide – DOC. 8188B 15 Volvo Drive Rockleigh, NJ 07647 10.03 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
Need help?
Do you have a question about the C2-AUDIO-6PAK and is the answer not in the manual?
Questions and answers