Page 1
EA00004 User Manual EA00004 User Manual EA00004 Telematics Device QSZTRACEA00004UM0101 Version: 1.01 QSZTRACEA00004UM0101...
Page 2
QSZTRACEA00004UM0101 Copyright This document contains proprietary technical information which is the property of Queclink. Copying of this document, distribution to others or using or communication of the contents thereof is forbidden without express authority. Offenders are liable to the payment of damages.
Wi-Fi, Bluetooth and GPS positioning modules. The EA00004 is designed to integrate within the scooter to provide communication to Bird Servers via LTE, provide local Bluetooth and 802.11 communications, and control vehicle behaviors such as remotely lock/unlock, track vehicle position, report status of the scooter.
EGPRS/LTE Cat-M1/LTE EA00004 Cat-NB1/GNSS tracker 125.5mm*62.08mm*101.0mm 3. Interface Definition The EA00004 harness have 24-pin interface connector. It contains the connections for power, Speaker, headlight and so on. The sequence and description of the connector are shown in the following figure: QSZTRACEA00004UM0101...
Page 7
Figure 2. 24-pin Connector of the EA00004 Table 5. Description of 24-pin Connections Index Description Comment Power GND 36V Perm Power 12V CAN_L CAN_L PWR_ENA Power ENA CAN_H CAN_H BR2_5V BR2_Input BR2_GND BR2_GND BR1_5V BR1_Input BR2_WP BR2_Wake up BR1_GND BR1_GND...
4. Device Cable Color Table 6. EA00004 Device Cable Color Definition Definition Color Pin No. Cable Black 36V Perm CAN_L Green PWR_ENA Blue CAN_H Yellow BR2_5V BR2_GND Black BR1_5V BR2_WP Green BR1_GND Black BR1_WP Orange TR_5V TR_WP1 Yellow TR_GND Black...
5. Started 5.1. Opening and Closing the Casing Figure 3. Open Top Cover To open/close: Loosen or fasten the screws to open or to close. 5.2. Installing a SIM Card Install the SIM card into the holder when power is off as shown blow. Take care to align the cut mark, and then close the case.
5.3. Power Supply Connection The red wire is power line ,the black wire is ground line and blue wire is power EAN line . The input voltage range for this device is from 12V to 60V DC. Figure 5. Example of Connection for power 5.4.
5.6. Throttle The blue wire is throttle weak up 2 line, the black wire is ground line, the red wire is power line, the yellow wire is throttle weak up 1 line. Figure 8. Example Connection to Throttle 5.7. Brake Right The black wire is ground line, the red wire is power line, the orange wire is weak up line.
Figure 10. Example connection to brake left 5.9. Headlight The white wire is ground line, the green wire is power line. Figure 11. Example connection to headlight 5.10. Speaker The white wire is ground line, the green wire is power line. Figure 12.
BLE working mode explanation 7.1. EA00004 is installed in the shared scooter and supplied by the main battery of scooter. With the external power(main battery of scooter) supplying , the BLE of EA00004 works. Otherwise with the backup battery of EA00004 supplying, BLE stops working.
WiFi instructions 9.2. Use the USB cable to configure the software of the product (the software will define that the product will automatically open WIFI function). After WiFi is turned on, the MAC address of the nearby WiFi signal will be searched; the signal will be sent to the background terminal through LTE function of the product, and the background terminal will locate the signal.
10. FCC Certification Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.
11. IC Certification ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.