Summary of Contents for Backyard Products GAMBREL 12' x 12'
Page 1
16432 PART 1 STOP! STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll free number: 1-888-827-9056 or email: customerservice@backyardproductsllc.com Our staff is ready to provide assistance April through October M-F 8:00 AM to 7:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST...
16432 03/01/2021 ASSEMBLY MANUAL PART 1 GAMBREL 12' x 12' (365,8 x 365,8 cm) BUILDING SIZE ACTUAL FLOOR SIZE 12' x 12' (365,8 x 365,8 cm) 12' x 12' (365,8 x 365,8 cm) BASE MODEL +1: 12' x 4' Extender 12' x 16' (365,8 x 487,7 cm) 12' x 16' (365,8 x 487,7 cm) +1: 12' x 8' Extender...
Page 4
TOOLS Required Optional K Phillips K Tool Belt/ K Utility Knife Screwdriver Nail Pouch K Shingle Blades K Drill / Driver K Tin Snips K 3/8" Drill Bit K Caulk Gun (for drip edge) K #2 Philips Drive Bit K Chalk Line K Hammer K Paint Tools K Level...
ADDITIONAL MATERIALS FOUNDATION OR FLOOR MATERIALS • This shed does not include any floor or leveling materials. • See the FLOOR LEVELING section on page 10 for recommended methods and suggested materials to properly level your floor, as this will vary depending on your specific site. REINFORCED WOOD FLOOR FRAME (OPTIONAL) IMPORTANT! Depending on your specific use you may want to construct a heavy duty floor frame by adding additional floor joists (shown below as shaded).
Page 6
ADDITIONAL MATERIALS COMPLETING YOUR SHED You will need these additional materials: 12x12' 12x16' 12x20' 12x24' 12x12' 12x16' 12x20' 12x24' Paint for trim/Quart 3-TAB SHINGLES (Bundles)..Use 100% acrylic latex exterior paint. PAINT FOR SIDING (Gallons)..Caulk Tubes ... Use 100% acrylic latex exterior paint. Use acrylic paintable (2) coats recommended.
Page 7
PARTS IDENTIFICATION AND SIZES WOOD SIZE CONVERSION CHART Double letter part identification Nominal Board Size Actual Size is stamped on some parts. 2 x 4 ....1-1/2" x 3-1/2" (3,8 x 8,9 cm) 1 x 4 ....3/4" x 3-1/2" (1,9 x 8,9 cm) •...
Page 8
PANEL & DOORS PARTS LIST NOTE: Panel parts are not stamped with part identification. 3/8 x 48 x 84" 3/8 x 23-7/8 x 84" (1 x 121,9 x 213,4 cm) (1 x 60,6 x 213,4 cm) ROOF PANELS Roof panels are 7/16" (1,1 cm) thick. 11-7/8"...
DOOR TRIM 19/32" x 2-1/2" x 26-5/8" (1,5 x 6,3 x 67,7 cm) 19/32" x 2-1/2" x 39-7/8" (1,5 x 6,3 x 101,3 cm) 19/32" x 2-1/2" x 39-7/8" (1,5 x 6,3 x 101,3 cm) 69" (175,3 cm) Door Stiffener 19/32"...
Page 10
GAMBREL EXTENDER KIT PARTS LIST Inventory your parts before you begin. We suggest sorting parts by the category they are listed in. WOOD SIZE CONVERSION CHART Part identification is stamped on some parts. Nominal Board Size Actual Size 2 x 4 ....1-1/2" x 3-1/2" (3,8 x 8,9 cm) 1 x 4 ....3/4"...
Page 11
CONCRETE FOUNDATION If you choose to install your kit on a concrete slab refer to the diagram below. Attach the sill plates on the foundaton as shown, and continue on to page 14. Treated Sill Plate Caulk between sill plate and concrete.
Page 12
OPTIONAL WOOD FRAME FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS (Typical for 12' x 12' Kit) Measurements to centers of 4x4's.
Page 13
LEVELING & SQUARING THE FLOOR FRAME (Not Included) LEVEL AND SQUARE FLOOR FRAME Before attaching fl oor decking, it is important to level and square the fl oor frame. A level and square fl oor frame is required to correctly construct your shed. See page 10 for the preferred fl oor leveling method.
Page 14
IMPORTANT! I M P O R T A N T ! NOTE: 12' x 12' Gambrel shown standard throughout manual Ensure the floor frame is level after installing floor panels. Re-level if needed. • The floor should used as a stable work surface for wall construction. •...
Page 16
WALL CONFIGURATION GUIDE Create your own style of shed. Choose your door location. Compare this guide with the wall index to find the corresponding pages. 12' x 12' 12' x 16' HINT: 12' x 20' 12' x 24' HINT:...
Page 17
WALL INDEX As another option, eave walls with doors can be reversed during assembly. 12' x 12' After assembling the walls for your 12' x 12' shed, go to page 56 for wall installation. 12' x 12' 12' x 12' V-1 12' x 12' V-2 Door is on the 12' Door is on the 12'...
Page 18
DOOR HEADER Assemble this door header before building any walls! PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 67" (5,1 x 10,2 x 170,2 cm) 7/16 x 3-1/4 x 66-3/4" (1,1 x 8,3 x 170,2 cm) BEGIN Place (1) AM and OSB end-to-end on fl at surface, fl ush in middle. Center OSB on top of AM.
Page 19
WALL PANEL INSTALLATION HINTS & EXAMPLES PARTS REQUIRED: 2" (5,1 cm) 2x3" TEMP. SPACER 3/4" GAUGE BLOCK 3/8 x 48 x 84" (1 x 121,9 x 213,4 cm ) Ensure your wall is square by installing one panel and squaring frame. Install all wall panels with the primed side facing up.
Page 20
GABLE WALL 01 WITH DOOR PARTS REQUIRED: 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 3" (7,6 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 96"...
Page 21
GABLE WALL 01 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x166 2" (5,1 cm) 23-7/8 x 84" Temporary Brace (60,6 x 213,4 cm) 69" (75,3 cm) Door Stiffener Install the left panel 1-1/2" from the top plate. 1-1/2" Flush (3,8 cm) Use a 2x3 spacer for 3/4"...
Page 22
12' GABLE WALL 02 PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) BEGIN Orient parts on edge on floor as shown.
Page 23
12' GABLE WALL 02 PARTS REQUIRED: x150 2" (5,1 cm) 48 x 84" (121,9 x 213,4 cm ) 1-1/2" (3,8 cm) 3/4" BEGIN HERE Install 48" x 84" panel 1-1/2" (1,9 cm) from the top plate. Use a 2x3 spacer for 6"...
Page 24
12' GABLE WALL 03 PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) BEGIN Orient parts on edge on floor as shown.
Page 25
12' GABLE WALL 03 PARTS REQUIRED: x142 2" (5,1 cm) 23-7/8 x 84" 48 x 84" (60,6 x 213,4 cm) (121,9 x 213,4 cm ) 1-1/2" (3,8 cm) 3/4" BEGIN HERE Install 48" x 84" panel 1-1/2" (1,9 cm) from the top plate. Use a 2x3 spacer for 6"...
Page 26
12' EAVE WALL 04 PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) 2 x 4 x 78-1/2"...
Page 27
12' EAVE WALL 04 PARTS REQUIRED: x120 2" (5,1 cm) 48 x 84" (121,9 x 213,4 cm ) 3/4" BEGIN HERE 3-1/2" (1,9 cm) Install 48" x 84" panel (8,9 cm) 1-1/2" from the top plate. 1-1/2" (3,8 cm) Use a 2x3 spacer for consistent measurement.
Page 28
12' EAVE WALL 05 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) 3" (7,6 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 2 x 4 x 44-3/8"...
Page 29
12' EAVE WALL 05 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x136 2" (5,1 cm) 23-7/8 x 84" Temporary Brace (60,6 x 213,4 cm) 69" (75,3 cm) Door Stiffener Install the left panel 1-1/2" from the top plate. 1-1/2" Flush (3,8 cm) Use a 2x3 spacer for 3/4"...
Page 30
12' EAVE WALL 06 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) 3" (7,6 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 2 x 4 x 44-3/8"...
Page 31
12' EAVE WALL 06 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x129 2" (5,1 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" from the top plate. 1-1/2" Flush (3,8 cm) Use a 2x3 spacer for...
Page 32
16' EAVE WALL 07 PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 92-5/8"...
Page 33
16' EAVE WALL 07 PARTS REQUIRED: x170 2" (5,1 cm) 48 x 84" (121,9 x 213,4 cm ) Install (1) 48" x 84" panel 1-1/2" from 3/4" BEGIN HERE (1,9 cm) the top plate. 1-1/2" (3,8 cm) Use a 2x3 spacer for consistent 6"...
Page 34
16' EAVE WALL 08 PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 92-5/8"...
Page 35
16' EAVE WALL 08 PARTS REQUIRED: x192 2" (5,1 cm) 23-7/8 x 84" 48 x 84" (121,9 x 213,4 cm ) (60,6 x 213,4 cm) Install (1) 48" x 84" panel 1-1/2" from 3/4" BEGIN HERE (1,9 cm) the top plate. 1-1/2"...
Page 36
16' EAVE WALL 09 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 68"...
Page 37
16' EAVE WALL 09 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x164 2" (5,1 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" 1-1/2" Flush (3,8 cm) from the top plate. 3/4"...
Page 38
16' EAVE WALL 10 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 68"...
Page 39
16' EAVE WALL 10 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x186 2" (5,1 cm) 23-7/8 x 84" (60,6 x 213,4 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" 1-1/2"...
Page 40
16' EAVE WALL 11 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 68"...
Page 41
16' EAVE WALL 11 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x179 2" (5,1 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" 1-1/2" Flush (3,8 cm) from the top plate. 3/4"...
Page 42
20' EAVE WALL 12 PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 92-5/8"...
Page 43
20' EAVE WALL 12 PARTS REQUIRED: x220 2" (5,1 cm) 48 x 84" (121,9 x 213,4 cm ) Install (1) 48" x 84" panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2" nails spaced 6" apart on edges and 12" inside panel. Note the panel lip-edge/square edge orientation.
Page 44
20' EAVE WALL 13 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 68"...
Page 45
20' EAVE WALL 13 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x236 2" (5,1 cm) 23-7/8 x 84" (60,6 x 213,4 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2"...
Page 46
20' EAVE WALL 14 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 68"...
Page 47
20' EAVE WALL 14 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x214 2" (5,1 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2"...
Page 48
20' EAVE WALL 15 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 68"...
Page 49
20' EAVE WALL 15 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x236 2" (5,1 cm) 23-7/8 x 84" (60,6 x 213,4 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2"...
Page 50
24' EAVE WALL 16 PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm) 2 x 4 x 48"...
Page 51
24' EAVE WALL 16 PARTS REQUIRED: x270 2" (5,1 cm) 48 x 84" (121,9 x 213,4 cm ) Install (1) 48" x 84" panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2" nails spaced 6" apart on edges and 12" inside panel. Note the panel lip-edge/square edge orientation.
Page 52
24' EAVE WALL 17 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 2 x 4 x 48"...
Page 53
24' EAVE WALL 17 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x264 2" (5,1 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2"...
Page 54
24' EAVE WALL 18 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 2 x 4 x 48"...
Page 55
24' EAVE WALL 18 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x286 2" (5,1 cm) 23-7/8 x 84" (60,6 x 213,4 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2"...
Page 56
24' EAVE WALL 19 WITH DOOR PARTS REQUIRED: x102 3" (7,6 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 2 x 4 x 7" (5,1 x 10,2 x 17,8 cm) 3" (7,6 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 2 x 4 x 48"...
Page 57
24' EAVE WALL 19 WITH DOOR PARTS REQUIRED: 3" (7,6 cm) x264 2" (5,1 cm) Temporary Brace 48 x 84" 69" (75,3 cm) Door Stiffener (121,9 x 213,4 cm ) Install the left panel 1-1/2" from the top plate. Use a 2x3 spacer for consistent measurement. Secure panel with 2"...
Page 58
12' GABLE WALL 02 INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 69" (175,3 cm) Door Stiffener 3" (7,6 cm) 2" (5,1 cm) BEGIN 1-1/2" (3,8 cm) Center 12' gable wall on the 144" (365,8 cm) fl oor dimension. 1-1/2" (3,8 cm) overlap is to the top. Use OO as a temporary brace.
Page 59
12' EAVE WALL 04 INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 1-1/2" (3,8 cm) 3" (7,6 cm) Fig. B BEGIN Place 12' eave wall centered on fl oor. 1-1/2" (3,8 cm) overlap is to the top. 2"...
Page 60
2nd 12' EAVE WALL 04 INSTALLATION PARTS REQUIRED: 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 3" (7,6 cm) 1-1/2" (3,8 cm) Fig. B BEGIN 1-1/2" (3,8 cm) Place 2nd 12' eave wall centered on fl oor 1-1/2" (3,8 cm) overlap is to the top. 2"...
Page 61
12' GABLE WALL 01 WITH DOOR INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 3" (7,6 cm) 1-1/2" (3,8 cm) Fig. B BEGIN 2" (5,1 cm) Place 12' gable wall on fl oor, centered Screw between installed walls. Secure wall with 2"...
Page 62
12' x 12' WALL DOUBLERS INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 3" (7,6 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2 x 4 x 96"...
Page 63
12' GABLE WALL 02 INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 69" (175,3 cm) Door Stiffener 3" (7,6 cm) 2" (5,1 cm) 1-1/2" BEGIN (3,8 cm) Center 12' wall on the 120" (304,8 cm) fl oor dimension. 1-1/2" (3,8 cm) overlap is to the top. Use OO as a temporary brace.
Page 64
1st 16' EAVE WALL 07 INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) Temporary Brace 1-1/2" (3,8 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2" (5,1 cm) 3" (7,6 cm) Fig. B BEGIN Place 1st 16' eave wall centered on fl oor. 1-1/2"...
Page 65
2nd 16' EAVE WALL (07 or 08) INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 2" (5,1 cm) 3" (7,6 cm) Temporary Brace 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2" (5,1 cm) 1-1/2" BEGIN (3,8 cm) 3" (7,6 cm) Screws Place 2nd 16' wall centered on fl oor.
Page 66
2nd 16' EAVE WALL (07 or 08) INSTALLATION PARTS REQUIRED: 1-1/2" (3,8 cm) 3" (7,6 cm) 3" (7,6 cm) Screw Fig. D 6" (15,2 cm) 1-1/2" (3,8 cm) Nail 16' wall panel to 12' wall stud with 1-1/2" nails spaced 6" apart. Nails Secure gable wall top plate with (1) 3"...
Page 67
12' GABLE WALL 01 WITH DOOR INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 3" (7,6 cm) 1-1/2" (3,8 cm) Fig. B BEGIN 2" (5,1 cm) Place 12' gable wall on fl oor, centered Screw between installed walls. Secure wall with 2"...
Page 68
12' x 16' WALL DOUBLERS INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 3" (7,6 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2 x 4 x 96"...
Page 69
12' GABLE WALL 02 INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 69" (175,3 cm) Door Stiffener 3" (7,6 cm) 2" (5,1 cm) 1-1/2" BEGIN (3,8 cm) Center 12' wall on the 120" (304,8 cm) fl oor dimension. 1-1/2" (3,8 cm) overlap is to the top. Use OO as a temporary brace.
Page 70
1st 20' EAVE WALL 12 INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) Temporary Brace 1-1/2" (3,8 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2" (5,1 cm) 3" (7,6 cm) Fig. B BEGIN Place 1st 20' eave wall 12 centered on fl oor. 2"...
Page 71
2nd 20' EAVE WALL 12 INSTALLATION PARTS REQUIRED: 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 3" (7,6 cm) Temporary Brace 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) BEGIN 2" (5,1 cm) 3" (7,6 cm) Place 2nd 20' wall 12 centered on fl oor.
Page 72
2nd 20' EAVE WALL 12 INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 1-1/2" (3,8 cm) Secure 20' wall panel to 12' wall stud with 1-1/2" nails spaced 6" apart. 3" (7,6 cm) Screw Fig. D Secure wall top plate with (1) 3" screw at the corner at an angle as shown (Fig.
Page 73
12' GABLE WALL 01 WITH DOOR INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 3" (7,6 cm) 1-1/2" (3,8 cm) Fig. B BEGIN 2" (5,1 cm) Place 12' gable wall on fl oor, centered Screw between installed walls. Secure wall with 2"...
Page 74
12' x 20' WALL DOUBLERS INSTALLATION PARTS REQUIRED: PARTS REQUIRED: 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 3" (7,6 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2 x 4 x 96"...
Page 75
12' GABLE WALL 02 INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 69" (175,3 cm) Door Stiffener 3" (7,6 cm) 2" (5,1 cm) 1-1/2" BEGIN (3,8 cm) Center 12' wall on the 120" (304,8 cm) fl oor dimension. 1-1/2" (3,8 cm) overlap is to the top. Use OO as a temporary brace.
Page 76
1st 24' EAVE WALL 16 INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) Temporary Brace 1-1/2" (3,8 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2" (5,1 cm) 3" (7,6 cm) Fig. B BEGIN Place 1st 24' eave wall 16 centered on fl oor.
Page 77
2nd 24' EAVE WALL 16 INSTALLATION PARTS REQUIRED: 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 3" (7,6 cm) Temporary Brace 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) BEGIN Place 2nd 24' wall 16 2" (5,1 cm) 3"...
Page 78
2nd 24' EAVE WALL 16 INSTALLATION PARTS REQUIRED: 3" (7,6 cm) 1-1/2" (3,8 cm) Secure 24' wall panel to 12' wall stud with 1-1/2" nails spaced 6" apart. 3" (7,6 cm) Fig. D Screw Secure wall top plate with (1) 3" screw at the corner at an angle as shown (Fig.
Page 79
12' GABLE WALL 01 WITH DOOR INSTALLATION PARTS REQUIRED 2" (5,1 cm) 3" (7,6 cm) 2" (5,1 cm) 1-1/2" (3,8 cm) 3" (7,6 cm) Fig. B BEGIN 2" (5,1 cm) Place 12' gable wall on fl oor, centered Screw between installed walls. Secure wall with 2"...
Page 80
12' x 24' WALL DOUBLERS INSTALLATION PARTS REQUIRED: PARTS REQUIRED: 2 x 4 x 44-3/8" (5,1 x 10,2 x 112,7 cm) 3" (7,6 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) 3" (7,6 cm) 2 x 4 x 92-5/8" (5,1 x 10,2 x 235 cm) 2 x 4 x 96"...
Page 81
Please continue to the included booklet PART 2 to complete your shed.