Advertisement
Quick Links
Advertisement
Related Manuals for Advantech SmartStart
Summary of Contents for Advantech SmartStart
- Page 1 Start Guide SmartStart, SmartFlex, SmartMotion...
-
Page 2: Safety Instructions
Start Guide Safety instructions Please take care to following instructions: Use the router in compliance with national and international law and in compliance with any special or additional restrictions regulating the use of the router in the various appli- cations and environments. To avoid possible injury and/or damage to the device, observe the relevant provisions and standards. -
Page 3: Product Disposal Instructions
flash drive medium. If you are interested in obtaining the source, please contact us at: techSupport@advantech-bb.com Modifications and debugging of LGPL-linked executables: The manufacturer of the device hereby grants the right to use debugging techniques (e.g. - Page 4 Start Guide QSG-0002-EN, August 4, 2021 Released in the Czech Republic...
- Page 5 SmartStart SmartStart Router SL302, SL304, SL305, SL306 QSG-0002-EN, August 4, 2021 Released in the Czech Republic...
-
Page 6: First Use
SmartStart First Use Before applying power to the router, connect all the components that you need for your applications. Do not run the router without an antenna connected to the main antenna connector as the energy from the transmission is effectively reflected by the open end and can damage the equipment. - Page 7 SmartStart Disconnect the router from the power supply before handling the SIM card! 3. Power The router requires an external DC power supply. The DC voltage required is between +9 and +36 V DC. The router has built-in protection against reverse polarity without signaling.
- Page 8 SmartStart 4. Ethernet For an initial configuration, made in a web browser, connect a PC by an Ethernet cable to the default LAN interface, use the ETH port, see the figure above. By default, this interface has the following configuration:...
- Page 9 Hereby, Advantech Czech s.r.o. declares that the radio equipment type SmartStart SL304 and SL305 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: icr.advantech.cz/eudoc...
- Page 10 SmartStart QSG-0002-EN, August 4, 2021 Released in the Czech Republic...
- Page 11 SmartFlex SmartFlex Router SR300, SR303, SR304, SR305, SR306, SR307, SR308, SR309, SR310 QSG-0002-EN, August 4, 2021 Released in the Czech Republic...
- Page 12 SmartFlex Hazardous Locations Installation Instructions These instructions apply for SR300, SR303 and SR305 versions with appropriate labeling only! These devices are open-type devices that are to be installed in an enclosure suitable for the environment and can only be accessed with the use of a tool or key. This equipment is suitable for use in Class I, Division 2, Groups A, B, C, AND D OR non- hazardous locations only.
- Page 13 SmartFlex 1. Antenna Use an SMA connectors to connect the antennas to the router, see the figure below. The main antenna is connected to the ANT connector. The second diversity antenna can be connected to the DIV connector to improve the quality and reliability of a wireless link. 2.
- Page 14 SmartFlex 3. Power The router requires an external DC power supply. The DC voltage required is between +10 to +60 V DC. The router has built-in protection against reverse polarity without signaling. Connect the power supply cable to the PWR connector on the front panel of the router, see the figure below.
- Page 15 Hereby, Advantech Czech s.r.o. declares that the radio equipment type SmartFlex SR300 (versions with radio interface only), SR303, SR304, SR305, SR306, SR307 and SR310 is in compliance with Directive 2014/53/EU. SmartFlex SR300 versions without radio interface are in compliance with the essential require- ments and other relevant provisions of Directives 2014/30/EU and 2014/35/EU.
- Page 16 SmartFlex QSG-0002-EN, August 4, 2021 Released in the Czech Republic...
- Page 17 SmartMotion SmartMotion Router ST352, ST355 QSG-0002-EN, August 4, 2021 Released in the Czech Republic...
- Page 18 SmartMotion First Use Before applying power to the router, connect all the components that you need for your applications. You cannot operate the router without a connected antenna, inserted SIM card, nor a connected power supply. Do not run the router without an antenna connected to the main antenna connector as the energy from the transmission is effectively reflected by the open end and can damage the equipment.
- Page 19 SmartMotion Before handling the SIM card disconnect the router from the power supply! 3. Power The router requires an external DC power supply. The DC voltage required is between +10 to +60 V DC. The router has built-in protection against reverse polarity without signaling. Connect the power supply cable to the PWR connector on the front panel of the router, see the figure below.
- Page 20 Hereby, Advantech Czech s.r.o. declares that the radio equipment type SmartMotion ST352 and ST355 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: icr.advantech.cz/eudoc...