Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantech SmartStart Series
Summary of Contents for Advantech SmartStart Series
- Page 1 Start Guide SmartStart, SmartFlex, SmartMotion...
-
Page 2: Safety Instructions
Start Guide Safety instructions Please take care to following instructions: Use the router in compliance with national and international law and in compliance with any special or additional restrictions regulating the use of the router in the various appli- cations and environments. To avoid possible injury and/or damage to the device, observe the relevant provisions and standards. -
Page 3: Product Disposal Instructions
flash drive medium. If you are interested in obtaining the source, please contact us at: techSupport@advantech-bb.com Modifications and debugging of LGPL-linked executables: The manufacturer of the device hereby grants the right to use debugging techniques (e.g. - Page 4 Start Guide QSG-0002-EN, January 24, 2020 Released in the Czech Republic...
- Page 5 SmartStart SmartStart Router SL302, SL304, SL306 QSG-0002-EN, January 24, 2020 Released in the Czech Republic...
-
Page 6: First Use
SmartStart First Use Before applying power to the router, connect the components that you required for your applications. You cannot operate the router without a connected antenna, inserted SIM card, nor a connected power supply. If you do not have connected the main antenna during operation of the router, the router can be damaged! 1. - Page 7 SmartStart Before handling the SIM card disconnect the router from the power supply! 3. Power The router requires an external DC power supply. The DC voltage required is between +9 to +36 V DC. The router has built-in protection against reverse polarity without signaling. Connect the power supply cable to the PWR connector on the front panel of the router (see the figure below).
- Page 8 SmartStart 4. Ethernet An Ethernet cable may be connected to the ETH connector (designated as ETH0 in some versions of this router) on the front panel (see the figure above). By default, the Ethernet port is configured as follows: Connector Purpose Default Setting LAN port (default)
-
Page 9: Important Notes
User’s Manual and Configuration Manual for the router can be found and downloaded on this web site: www.advantech-bb.cz/download Hereby, Advantech Czech s.r.o. declares that the radio equipment type SmartStart SL304 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.advantech-bb.cz/eudoc... - Page 10 SmartStart QSG-0002-EN, January 24, 2020 Released in the Czech Republic...
- Page 11 SmartFlex SmartFlex Router SR300, SR303, SR304, SR305, SR306, SR307, SR308, SR309 QSG-0002-EN, January 24, 2020 Released in the Czech Republic...
-
Page 12: Hazardous Locations Installation Instructions
SmartFlex Hazardous Locations Installation Instructions These instructions apply for SR300, SR303 and SR305 versions with appropriate labeling only! These devices are open-type devices that are to be installed in an enclosure suitable for the environment and can only be accessed with the use of a tool or key. This equipment is suitable for use in Class I, Division 2, Groups A, B, C, AND D OR non- hazardous locations only. - Page 13 SmartFlex 1. Antenna Use an SMA connector to connect the antennas to the router. The main antenna is con- nected to the router by screwing on the ANT connector (see the figure below). A second diversity antenna can also be connected to the DIV connector to improve performance. 2.
- Page 14 SmartFlex 3. Power The router requires an external DC power supply. The DC voltage required is between +10 to +60 V DC. The router has built-in protection against reverse polarity without signaling. Connect the power supply cable to the PWR connector on the front panel of the router (see the figure below).
- Page 15 User’s Manual and Configuration Manual for the router can be found and downloaded on this web site: www.advantech-bb.cz/download Hereby, Advantech Czech s.r.o. declares that the radio equipment type SmartFlex SR300 (versions with radio interface only), SR303, SR304, SR305, SR306 and SR307 is in compliance with Directive 2014/53/EU.
- Page 16 SmartFlex QSG-0002-EN, January 24, 2020 Released in the Czech Republic...
- Page 17 SmartMotion SmartMotion Router ST352, ST355 QSG-0002-EN, January 24, 2020 Released in the Czech Republic...
- Page 18 SmartMotion First Use Before applying power to the router, connect the components that you required for your applications. You cannot operate the router without a connected antenna, inserted SIM card, nor a connected power supply. If you do not have connected the main antenna during operation of the router, the router can be damaged! 1.
- Page 19 SmartMotion Before handling the SIM card disconnect the router from the power supply! 3. Power The router requires an external DC power supply. The DC voltage required is between +10 to +60 V DC. The router has built-in protection against reverse polarity without signaling. Connect the power supply cable to the PWR connector on the front panel of the router (see the figure below).
- Page 20 Hereby, Advantech Czech s.r.o. declares that the radio equipment type SmartMotion ST352 and ST355 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.advantech-bb.cz/eudoc...