Ratings And Specifications; Amplifier Units - Omron E3X-DACLRX1P-M3J 0.3M Manual

Ratings and Specifications

Amplifier Units

Item
Light source (wavelength)
Sensing method
Number of registered
colors
Power supply voltage
Power consumption
Control outputs
Number of control outputs
Remote control input
Protection circuits
Super-high-speed mode *3
Response
High-speed mode
time
Standard mode
High-resolution mode
Sensitivity setting (color regis-
tration, allowable range)
Operation mode
Timer function
Control outputs
Functions
Remote control
Display switch *4
Initialization
Zero reset
Indicators
Digital display
Display direction
Ambient illumination (Receiver
side)
Ambient temperature range *5
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Degree of protection
Connection method
Weight (packed state)
Case
Materials
Cover
*1. When teaching with/without a workpiece, the best sensing method will be automatically selected (RGB ratio (C Mode) or light intensity determination (I Mode)). If
color differences are not strong enough and RGB ratios would result in unstable detection, then light intensity determination (I Mode) will be selected.
The detection mode can be set to C, I, or Black Mode.
*2. Input Specifications
2
Type Single colour
White LED (420 to 700 nm)
C Mode: RGB ratio determination (or I Mode: Light intensity determination for red, green, or blue;
Black Mode: Determination of total light intensity for red, green, and blue) *1
1
12 to 24 VDC 10%, ripple (p-p) 10% max.
960 mW max. (current consumption: 40 mA max. at power supply voltage of 24 VDC)
NPN or PNP open collector
Load power supply voltage: 26.4 VDC max.
Load current: 50 mA max. (residual voltage: 2 V max.)
1
---
Reverse polarity for power supply connection, Output short-circuit, Reversed output polarity protection
Operate or reset: 60 s
Operate or reset: 300 s
Operate or reset: 1 ms
Operate or reset: 4 ms
– Object teaching (good sample) with auto-tolerance
– 2-point teaching (good and bad sample)
ON for match (ON for same color as registered color) or ON for mismatch (ON for different color from registered color)
Timer type: OFF delay, ON delay, or one-short, Timer time: 1 ms to 5 s (variable)
---
---
Seven patterns total: Match + Threshold, Margin + Threshold, Analog bar display, Peak + Bottom, etc.
Initial reset (factory defaults) or user reset (saved
settings)
Supported
Operation indicator (orange)/I mode display
indicator (orange)
7-segment displays (Main display: Red, Sub-display: Green)
Switchable between normal and reversed.
Incandescent lamp: 3,000 lux
Sunlight: 10,000 lux
Operating: 25C to 55C, Storage: 30C to 70C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
20 M min. (at 500 VDC)
1,000 VAC at 50/60 Hz for 1 minute
Destruction: 10 to 50 Hz with a 1.5-mm double amplitude for 2 h each in X, Y and Z directions
2
Destruction: 500 m/s , for 3 times each in X, Y and Z directions
IEC IP50 (with Protective Cover attached)
Fiber connector with 30 cm PVC cable and M8 plug Pre-wired (standard cable length: 2 m)
Approx. 100 g
Polybutylene terephthalate (PBT)
Polycarbonate (PC)
E3X-DACLR
1 to 4 colour
4
(2-color simultaneous determination  2 banks)
2
No-voltage input (contact/transistor) *2
Operate or reset: 120 s
Operate or reset: 600 s
Operate or reset: 2 ms
Operate or reset: 8 ms
Output for each channel, AND output, and OR
output
Bank switching
(switching between banks A and B and banks C
and D)
Initial reset (factory defaults)
Not supported
Operation indicator for each channel (orange)