Ratings And Specifications - Omron E3Z-LT86-L Manual

Ratings and Specifications

Sensing
method
Response
NPN output
Model
Item PNP output
Sensing distance
Set distance range
Spot diameter (typical)
Standard sensing object
Minimum detectable
object (typical)
Differential travel
Black/white error
Directional angle
Light source (wavelength)
Power supply voltage
Current consumption
Control output
Residual output voltage
Output mode switching
Protection circuits
Response time
Sensitivity adjustment
Ambient illumination
(Receiver side)
Ambient temperature range
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Degree of protection
Connection method
Indicator
E3Z Laser Models
Through-beam
E3Z-LT61/-LT66
E3Z-LT81/-LT86
(when using E39-R1)
60 m *1
(when using E39-R12)
(when using E39-R6)
---
5 mm dia. at 3 m
Opaque:
12 mm dia. min.
6 mm dia. opaque object at 3 m
---
---
Receiver: 3 to 15°
Red LED (655 nm), JIS CLass 1, IEC Class 1, FDA Class II
Emitter: 15 mA
Receiver: 20 mA
Load power supply voltage: 26.4 VDC max., Load current: 100 mA max., Open collector output
Switch to change between light-ON and dark-ON
Reversed power supply
polarity protection,
Reversed power supply polarity protection, Output short-circuit protection,
Output short-circuit pro-
tection, and Reversed
output polarity protection
Operate or reset: 1 ms max.
One-turn adjuster
Operating: − 10 to 55 ° C, Storage: − 25 to 70 ° C (with no icing or condensation)
Operating: 35% to 85%, Storage: 35% to 95% (with no icing or condensation)
Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 500 m/s
Pre-wired cable (standard length: 2 m): E3Z-L@@1/-L@@3
Emitter for Through-bream Models has power indicator (orange) only.
Retro-reflective with
MSR function
Standard response
E3Z-LR61/-LR66 E3Z-LL61/-LL66
E3Z-LR81/-LR86 E3Z-LL81/-LL86
0.3 to 15 m
(100 × 100 mm):
0.2 to 7 m
(100 × 100 mm):
0.2 to 7 m
(100 × 100 mm):
(100 × 100 mm):
Opaque:
75 mm dia. min.
0.2 mm dia. stainless-steel pin gauge at 300 mm
12 to 24 VDC±10%, ripple (p-p): 10% max.
Load current of less than 10 mA: 1 V max.
Load current of 10 to 100 mA: 2 V max.
Mutual interference prevention, and Reversed output polarity protection
Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
20 MΩ min. at 500 VDC
1,000 VAC, 50/60 Hz for 1 min
2
3 times each in X, Y, and Z directions
IP67 (IEC 60529)
Standard M8 Connector: E3Z-L@@6/-L@@8
Operation indicator (orange)
Stability indicator (green)
Distance-settable (BGS models)
High-speed response
E3Z-LL63/-LL68
E3Z-LL83/-LL88
White paper White paper
(100 × 100 mm):
20 to 300 mm 25 to 300 mm
Black paper Black paper
(100 × 100 mm):
20 to 160 mm 25 to 100 mm
White paper White paper
(100 × 100 mm):
40 to 300 mm 40 to 300 mm
Black paper Black paper
(100 × 100 mm):
40 to 160 mm 40 to 100 mm
0.5 mm dia. at 300 mm
---
5% max. of set distance
5% at 160 mm 5% at 100 mm
---
30 mA max.
Operate or reset:
0.5 ms max.
Five-turn endless adjuster
5