Table of Contents
Advertisement
To check the step count
●
Display the TIME+DAILY screen.
Selecting a Timekeeping Mode Digital
l
Display Format
Note
The step count can show a value up to
●
99,999 steps. If the step count
exceeds 99,999, the maximum value
(99,999) remains on the display.
To prevent miscounts, the displayed
●
count does not increase for about 10
seconds after you start walking. After
you have been walking for about 10
seconds, the correct count appears,
including the steps you took during the
previous 10 seconds.
The step count is reset to zero at
●
midnight each day.
To save power, measurement stops
●
automatically if you take off the watch
(no watch movement) and do not
perform any operation for two or three
minutes.
Causes of Incorrect Step
Count
Any of the conditions below may make proper
counting impossible.
Walking while wearing slippers, sandals, or
●
other footwear that encourages a shuffling
gait
Walking on tile, carpeting, snow, or other
●
surface that causes a shuffling gait
Irregular walking (in a crowded location, in
●
a line where walking stops and starts at
short intervals, etc.)
Extremely slow walking or extremely fast
●
running
Pushing a shopping cart or baby stroller
●
In a location where there is a lot of vibration,
●
or riding on a bicycle or in a vehicle
Frequent movement of the hand or arm
●
(clapping, fanning movement, etc.)
Walking while holding hands, walking with
●
a cane or stick, or engaging in any other
movement in which your hand and leg
movements are not coordinated with each
other
Normal daily non-walking activities
●
(cleaning, etc.)
Wearing the watch on your dominant hand
●
Walking for 10 seconds or less
●
Watch Operation Guide 3506
Other Settings
This section explains other watch settings you
can configure.
Enabling the Button
Operation Tone
Use the procedure below to enable or disable
the tone that sounds when you press a button.
1.
Enter the Timekeeping Mode.
Navigating Between Modes
l
2.
Hold down (A) for at least two seconds.
This displays the Timekeeping Mode
setting screen.
Pointer
3.
Use (A) and (C) to move the pointer to
[BEEP].
4.
Press (B).
5.
Use (A) and (C) to move the pointer to
[OPERATION].
6.
Press (B).
7.
Use (A) and (C) to move the pointer to
[ON] (enabled) or [OFF] (disabled).
8.
Press (B) to complete the setting
operation.
After the setting operation is complete,
[SETTING COMPLETED] will appear for
a few seconds, and then the BEEP
(sound) setting screen will re-appear.
●
Mode while the operation tone is
disabled.
9.
Press (D) twice to exit the setting screen.
is displayed in the Timekeeping
Configuring Notification
Sound Settings
You can use the procedure below to enable or
disable the notification sound.
1.
Enter the Timekeeping Mode.
Navigating Between Modes
l
2.
Hold down (A) for at least two seconds.
This displays the Timekeeping Mode
setting screen.
Pointer
3.
Use (A) and (C) to move the pointer to
[BEEP].
4.
Press (B).
5.
Use (A) and (C) to move the pointer to
[NOTIFICATION].
6.
Press (B).
7.
Use (A) and (C) to select a notification
sound ON/OFF setting.
Enables sound for all
[ALL ON]
notifications.
Enables sound only for items
[USER]
specified by you.
Disables sound for all
[ALL OFF]
notifications.
Note
The configuration of [USER]
●
notifications can be changed using G-
SHOCK MOVE.
8.
Press (B) to complete the setting
operation.
After the setting operation is complete,
[SETTING COMPLETED] will appear for
a few seconds, and then the BEEP
(sound) setting screen will re-appear.
is displayed in the Timekeeping
●
Mode while the notification tone is
disabled.
9.
Press (D) twice to exit the setting screen.
29
Advertisement
Table of Contents
