Operation Mode Switch - Vitek VT-3620 ST Manual Instruction

• For children safety reasons do not leave poly-
ethylene bags used as a packaging unat-
tended.
•
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger
of suffocation!
•
Check the power cord and plug periodically.
Do not use the unit if its body, power plug or
power cord is damaged.
• To avoid damages, transport the unit in the
original package only.
• Do not use the unit if the power cord or plug
is damaged, if the unit malfunctions, after the
unit was dropped or damaged in any other
way.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
Keep the unit out of reach of children.
THIS UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature.
•
Unpack the unit and remove any stickers that
can prevent unit operation.
•
Check the unit for damages; do not use it in
case of damages.
• Before switching the unit on, make sure that
voltage of the mains corresponds to unit oper-
ating voltage.
•
Clean the unit body with a damp cloth and
then wipe it dry.
•
Wash all removable parts with warm water and
neutral detergent, then rinse and dry thor-
oughly before assembling.

OPERATION MODE SWITCH

The marks on the switch (8) correspond to the
following operation modes:
«0» – the meat grinder is off, the middle position
of the switch.
«ON» – the meat grinder is on, the fixed position
of the switch.
«R» – reverse mode, the switch position is not
fixed.
IM VT-3620.indd 5
ATTENTION!
• The meat grinder is intended to mince bone-
less meat for household use only.
•
Before grinding meat, make sure that meat is
fully defrosted, all bones and excess fat are
removed. Cut meat into small pieces (no more
than 2 cm x 2 cm x 6 cm), so they can fit easily
into the food tray (2) opening.
•
Place the unit on a flat dry surface.
• Make sure that ventilation openings on the
unit body are not blocked.
• Do not push the products with any foreign
objects or your fingers, use only the push-
ers (1) or (14) supplied with the unit.
•
Never immerse the meat grinder body, the
power plug or the power cord into water or
other liquids.
•
Do not try to process food with hard fiber (for
example, ginger or horseradish) in the meat
grinder.
• To avoid obstructions, do not apply excessive
force while pushing products with the push-
ers (1) or (14).
•
If any hard piece of food stops the feeder screw
or cutting blade rotation, immediately switch the
unit off by setting the switch (8) to the «0» (off)
position and use the screw reverse mode «R»
(reverse) to remove the obstruction before start-
ing again. To do this press and hold the switch (8)
in the position «R» for several seconds.
•
Do not run the unit for more than 5 minutes
continuously.
•
After 5 minutes of continuous use, switch
the unit off and allow it to cool down during
10-15 minutes before further operation.
• After you finish operating, switch the meat
grinder off, setting the switch (8) to the posi-
tion «0» and unplug the unit; after that you can
disassemble it.
MEAT PROCESSING
Press and hold the meat grinder head lock
1.
button (5).
Insert the meat grinder head (3) into the open-
2.
ing (4) matching the ledges on the head (3)
with the openings in the setting place (4) and
release the button (5) (pic. 1).
Then turn the meat grinder head (3) counter-
3.
clockwise until locking (pic. 2).
Install the screw (9) into the meat grinder
4.
head (3) body until bumping, slightly turning
it in different directions (pic. 3).
Install the crossed blade (10) (pic. 4).
5.
5
ENGLISH
17.11.2016 12:14:30