Before The First Use; Operation Mode Switch - Vitek VT-3625 Manual Instruction

ENGLISH
• For children safety reasons do not leave poly-
ethylene bags used as a packaging unat-
tended.
•
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger
of suffocation!
• Check the power cord and plug periodically.
•
Do not use the unit if its body, power plug or
power cord is damaged.
•
Do not use the unit if the power cord or plug
is damaged, if the unit malfunctions, after the
unit was dropped or damaged in any other way.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
To avoid damages, transport the unit in the
original package only.
• Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE IN
PRODUCTION AREAS AND WORK SPACES ARE
PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature.
•
Unpack the unit completely and remove any
packaging materials that can prevent the unit
operation.
• Check the unit for damages, do not use it in
case of damages.
•
Before switching the unit on, make sure that
voltage of the mains corresponds to unit oper-
ating voltage.
• Clean the unit body with a damp cloth and
then wipe it dry.
•
Wash all the removable parts (1, 2, 3, 9, 10,
11, 12, 13) with warm water and neutral deter-
gent, rinse and dry them thoroughly before
assembling.

OPERATION MODE SWITCH

The marks on the switch (8) correspond to the
following operation modes:
IM VT-3625.indd 4
«0» – the meat grinder is off, the middle posi-
tion of the switch.
«ON» – the meat grinder is on, the fixed posi-
tion of the switch.
«R» – reverse mode, the switch position is
not fixed.
ATTENTION!
•
The meat grinder is intended to mince bone-
less meat for household use only.
•
Before grinding meat, make sure that meat is
fully defrosted, all bones and excess fat are
removed. Cut meat into small pieces (no more
than 2 cm x 2 cm x 6 cm), so they can fit easily
into the food tray (2) opening.
•
Place the unit on a flat dry surface.
•
Make sure that the ventilation openings on the
unit body are not blocked.
•
Do not push the products with any foreign
objects or your fingers, use only the pusher
(1) supplied with the unit for pushing the prod-
ucts through.
• Never immerse the meat grinder body, the
power plug or the power cord into water or
other liquids.
•
Do not try to process food with hard fiber (for
example, ginger or horseradish) in the meat
grinder.
• To avoid obstructions, do not apply excessive
force while pushing meat with the pusher (1).
•
If any hard piece of food stops the feeder
screw or cutting blade rotation, immediately
switch the unit off by setting the switch to the
"0" (off) position and use the screw reverse
mode «R» (reverse) to remove the obstruc-
tion before starting again. To do this press and
hold the switch (8) in the position "R" for sev-
eral seconds.
• Do not run the unit for more than 5 minutes
continuously.
•
After 5 minutes of continuous use, switch
the unit off and allow it to cool down during
10-15 minutes before further operation.
•
After you finish operating, switch the meat
grinder off, setting the switch (8) to the posi-
tion «0» and unplug the unit; after that you can
disassemble it.
MEAT PROCESSING
• Press and hold the meat grinder head lock
button (5).
4
05.02.2018 17:51:07