1. Manuals
  2. Brands
  3. Briggs & Stratton Manuals
  4. Lawn Mower Accessories
  5. 1692149
  6. Operator's manual

Briggs & Stratton 1692149 Operator's Manual

Clean sweep twin catcher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Copyright © 2011 Briggs & Stratton Power Products Group, LLC
Milwaukee, WI
ATTACHMENT
OPERATOR'S
MANUAL
Clean Sweep
Twin Catcher
Model No.
Description
1692149
Clean Sweep Twin Catcher (for 30" Mower Decks)
1692150
Clean Sweep Twin Catcher (for 34" Mower Decks)
1709142 - K
Rev: K

Advertisement

Table of Contents
loading

Related Manuals for Briggs & Stratton 1692149

Summary of Contents for Briggs & Stratton 1692149

  • Page 1 OPERATOR’S MANUAL Clean Sweep Twin Catcher Model No. Description 1692149 Clean Sweep Twin Catcher (for 30” Mower Decks) 1692150 Clean Sweep Twin Catcher (for 34” Mower Decks) Copyright © 2011 Briggs & Stratton Power Products Group, LLC 1709142 - K...

  • Page 3: Table Of Contents

    Table of Contents TABLE OF CONTENTS Operator Safety ................General Warnings ..............Safety Decals ................Assembly ..................30” Models - Blade and Adapter Assembly ....... 34” Models - Baffl e, Blade, & Adapter Assembly ....... Frame & Bagger Support Assembly. - All ........Grass Catcher Assembly.

  • Page 4: Operator Safety

    Operator Safety WARNING Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed.

  • Page 5: Assembly

    Assembly 30” MODELS - BLADE AND ADAPTER 3. Install 5/16-18 x 2-1/4” carriage bolt (A, Figure 8) through front hole in mower deck along with cup (B), ASSEMBLY whiz flange nut (C), wing nut (D) and center lock nut (E). Blade Assembly - 30”...

  • Page 6: 34" Models - Baffle, Blade, & Adapter Assembly

    Assembly 34” MODELS - BAFFLE, BLADE, & ADAPTER Install Blades - Early Models with Splined Arbor ASSEMBLY 1. Remove existing discharge-side blade but retain hardware. Remove the retaining band (E, Figure 5b) Install Baffl e from the arbor shaft and remove the existing splined 1.

  • Page 7: Frame & Bagger Support Assembly. - All

    Assembly FRAME & BAGGER SUPPORT ASSEMBLY - GRASS CATCHER ASSEMBLY - All Models All Models Note: Cover and bag support are packaged as an assembly Note: Units with 0510 transmissions use anchors (A, Figure with long clevis pins and clips. It may be easier to separate 7) with a notch, all other units use anchor with no notch.
  • Page 8 Assembly 4. Raise the seat deck to expose the right-hand top duct. 7. Open grass bag cover and install grass bag frames (A, Figure 12) to support brackets (B). Make sure cover 5. See Figure 10. Cut out the exhaust shield mounting handle latches to grass bag frames.

  • Page 9: Installation / Removal

    Installation / Removal INSTALLATION & REMOVAL 3. Open grass bag cover and install grass bag frames (A, Figure 17) to support brackets (B). NOTE: For first-time installation, refer to Initial Setup & Installation. NOTE: If mower deck is equipped with Mulching Kit, the mulching baffles must be removed for grass collection.
  • Page 10 Installation / Removal 5. Apply dry talc to rubber seal at cover opening. Install tube (A, Figure 19) as far as possible into opening to clear adapter and install over adapter. Secure by WARNING rotating wire form (C, Figure 20) down into locked position over puck on adapter.

  • Page 11: Operation

    Operation BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important.

  • Page 12: Emptying The Bags

    Operation EMPTYING THE BAGS STORAGE Raise the bagger cover. If a plastic liner was not used, The adapter and tube should be removed for cleaning. unhook the bag and turn upside down to empty (use handle Unhook the wire form and remove the tube from the on bottom).

  • Page 13: Troubleshooting

    Troubleshooting The following table provides troubleshooting instructions for the more common and easily corrected problems. For problems not covered in the table, see your dealer. WARNING To avoid serious Injury, perform maintenance on the grass catcher only after stopping the engine and waiting for all moving parts to come to a complete stop.

  • Page 14: Warranty

    Warranty BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment that is defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of charge, any part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both.
  • Page 16 Briggs & Stratton Yard Power Products Group Copyright © 2010 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved...

This manual is also suitable for:

1692150

Table of Contents