Related Manuals for Briggs & Stratton LT 125
Summary of Contents for Briggs & Stratton LT 125
- Page 1 ATTACHMENT OPERATOR’S MANUAL Triple Catcher LT 125 Mfg. No. Description 1695598 LT125 Triple Catcher / 46 Mower 1737348 Rev. B Rev. Date 02/2009...
-
Page 3: Table Of Contents
Table of Contents Operator Safety ..............General Warnings ................. Safety Decals ..................Assembly................Baffle Installation .................. Hitch and Frame Installation ..............Tube Assembly ..................Operation................Collector Installation ................Attach Collector Bags ................Operation ....................Collector Removal ................. Storage ................NOTE: In these instructions, “left”... -
Page 4: Operator Safety
Operator Safety Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifi... -
Page 5: Assembly
Assembly Before beginning any service work turn WARNING: off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). Baffl e Installation 1. Lift side discharge chute (A, Figure 1). 2. Insert baffl e (B) through discharge opening and position baffl... -
Page 6: Hitch And Frame Installation
Assembly 4. Slide the hitch (A, Figure 3) onto the right and left shoul- Before beginning any service work turn WARNING: der bolts (B) of the rear frame support (C) . off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). - Page 7 Assembly 5. Install the bag and cover support (A, Figure 4) to upright 6. Attach cover assembly (B, Figure 5) to cover support support (B) using 3/8-16 x .875 bolt (C) and locknuts (D) bracket (A) using hinge pivots (C). Secure cover using as shown.
-
Page 8: Tube Assembly
Assembly Tube Assembly 1. Slide lower tube (A, Figure 8) underneath defl ector mounting bracket (B). Side tab (C) of chute fi ts inside the Frame Hung Mowers mower deck (D). 1. Remove existing hardware from wheel bracket (A, Figure 2. - Page 9 Assembly Frame Hung Mowers Assemble Upper & Middle Tube 1. Fit other side of lower tube (A, Figure 10) onto bolt (B) 1. Slide the upper tube (A, Figure 12) into cover (B) mounted on deck. aligning ridge (C) with cutout (D) as shown. 2.
-
Page 10: Operation
Operation 3. Raise the cover (C). Collector Installation 4. Attach collector bags (F) using grass bag hanger (G) to 1. Mount the hitch and frame assembly (A, Figure 14) onto bag hanger post. rear tractor frame. Note: It may be necessary to fold seat forward to allow 2. -
Page 11: Attach Collector Bags
Operation Attach Collector Bags 1. Raise the cover (A, Figure 15). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). Note: It may be necessary to fold seat forward to allow cover to stay in the raised position. Figure 15... -
Page 12: Operation
Operation Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. -
Page 13: Collector Removal
Operation Collector Removal 3. Loosen middle tube strap from lower chute (D) and remove middle / upper tube assembly (E). : Operation Without Bagger 4. Lift discharge defl ector (F). Rotate latch (G) upward on CAUTION For operation without bagger, the mower defl ector MUST front of lower chute. -
Page 14: Storage
Storage Storing The Grass Catcher Clean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove any debris from the screen on the underside of the lid. If paint has been scratched on metal parts, touch up with paint, or apply a thin fi... - Page 16 Briggs & Stratton Yard Power Products Group Copyright © 2009 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved...