Related Manuals for Briggs & Stratton 1694919
Summary of Contents for Briggs & Stratton 1694919
- Page 1 ATTACHMENT OPERATOR’S MANUAL 42” Snow Blade Mfg. No. Description 1694919 42” Remote Angling Snow Blade 1732529-B Revision: B...
-
Page 3: Table Of Contents
Table of Contents Operator Safety ................General Warnings ..............Safety Decals ................Features and Controls ..............Assembly..................Initial Setup................Install Reach on to Tractor ............Attach Lift Assembly to Snow Blade .......... Attach Snow Blade to Tractor............. Install Snow Blade Arm ............. Attche Control Arm Support Bracket to Tractor ...... -
Page 4: Operator Safety
Operator Safety Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. -
Page 5: Safety Decals
Operator Safety Safety Decals PREPARATION Several safety labels are installed on the unit to remind you • Disengage the PTO before making any adjustments. of important information while you are operating your unit. • Never attempt to make any adjustments while engine All DANGER, WARNING, CAUTION and instructional is running. -
Page 6: Features And Controls
Features & Controls WARNING Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and stop the unit. -
Page 7: Assembly
Assembly 25 13 Figure 2 Initial Setup Description Description Extension Spring Long Eye Bolt Hair Pin Short Eye Bolt Flat Washer Bottom Blade Rod Lift Rod Assembly 1.00” Cap Screw Lift Pivot Flange Nut Lock Washer Top Blade Rod .875” Cap Screw Control Arm Support Bracket Reach Washer... -
Page 8: Install Reach On To Tractor
Assembly Install Reach on to Tractor 6. Slide the reach (A, Figure 5) under tractor and lift to slide reach mounting arms (B) over reach support shaft 1. Remove mower deck. (C). 2. On right side of reach (A, Figure 3), install the bell crank (B) through the front holes . -
Page 9: Attach Lift Assembly To Snow Blade
Assembly Attaching Hitch Lift Assembly to Snow Blade 4. Insert the large loop of spring (A, Figure 9) through the hole (B) in hitch lift assembly and then the small loop 1. Attach the hitch lift assembly (A, Figure 7) to snow through eyebolt (C). -
Page 10: Install Snow Blade Arm
Assembly Install Snow Blade Lift Arm 4. Install the extension spring (A, Figure 13) into square hole (B) at the rear edge of the tractor frame. Note: The following steps are preformed under right rear 5. Secure the other end of extension spring to the “C” lift fender. -
Page 11: Attche Control Arm Support Bracket To Tractor
Assembly Attaching Control Arm Support Bracket to 5. Slide the control arm assembly (A, Figure 18) through the two adjustment arm joints (B). Secure the control Tractor arm with four hair pins (C). 1. On right side of tractor, install the control arm support bracket (A, Figure 15) using a 1.00”... -
Page 12: Operation
Operations Transporting DANGER For maximum ground clearance, transport the blade OPERATING ON SLOPES CAN BE DANGEROUS to and from work areas fully raised and angled straight Never operate on slopes greater than 17.6% (10°) ahead. which is a rise of 3-1/2 feet (106cm) vertically in 10 feet (607cm) horizontally. -
Page 13: Maintenance
Maintenance Figure 20 Schedule For Normal Care Care Required Schedule WARNING To avoid serious injury, perform maintenance on the Clean snow and ice from After each use. unit only when the engine is stopped and all moving the snow blade. parts have stopped. -
Page 14: Snow Blade Removal
Snow Blade Removal Travel Height Adjustment 4. Remove the hair pin (A, Figure 23) from bell crank (B) and remove the lift arm assembly (C). CAUTION Make sure to shut off the engine and lock the tractor brakes or block the rear wheels before beginning the snow blade removal process. - Page 15 Snow Blade Removal 6. Turn the front wheels fully to the left. 9. At back of tractor, slide reach mounting arms (A, Figure 26) out of the reach support shaft (B). Slide the reach 7. Remove the hair pin (A, Figure 25) and slide the latch from under the tractor.
-
Page 16: Troubleshooting
TroubleShooting Troubleshooting While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may WARNING eventually require that service be performed to allow it to • To avoid serious injury, perform maintenance on the continue operating properly. -
Page 17: Skid Shoe Adjustment
TroubleShooting Skid Shoe Adjustment Lift Adjustment On smooth surfaces such as concrete or asphalt, the In the fully raised position the attachment should be 4”-5” scraper bar should scrape the surface. On surfaces such off the ground. as gravel, the scraper bar should be set high enough so 1. -
Page 18: Storage
Storage IMPORTANT Note: Refer to Tractor Operator’s Manual for important information concerning safely storing your tractor. Daily Storage 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. -
Page 19: Warranty
Warranty LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment that is defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of charge, any part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both. - Page 20 Copyright © 2011 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved...