Briggs & Stratton 1695353 Operator's Manual
  1. Manuals
  2. Brands
  3. Briggs & Stratton Manuals
  4. Lawn Mower Accessories
  5. 1695353
  6. Operator's manual
Briggs & Stratton 1695353 Operator's Manual

Briggs & Stratton 1695353 Operator's Manual

38” turboless twin catcher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S
MANUAL
Turboless Twin Catcher
Turboless Twin Catcher
Mfg. No.
Description
1695353
38" Turboless Twin Catcher
C C A A U U T T I I O O N N : : R R e e a a d d a a n n d d
f f o o l l l l o o w w a a l l l l i i n n s s t t r r u u c c t t i i o o n n s s . .
Manual Part No. 1734772
Revision 01
Rev. Date 05/2007
TP 100-4528-01-AT-SMAN

Advertisement

Table of Contents
loading

Related Manuals for Briggs & Stratton 1695353

Summary of Contents for Briggs & Stratton 1695353

  • Page 1 Turboless Twin Catcher Mfg. No. Description 1695353 38” Turboless Twin Catcher C C A A U U T T I I O O N N : : R R e e a a d d a a n n d d f f o o l l l l o o w w a a l l l l i i n n s s t t r r u u c c t t i i o o n n s s .

  • Page 2: Read The Manual

    READ THE MANUAL The operator’s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation. Safe operating techniques, an explanation of the product’s features and controls, and maintenance information is included to help you get the most out of your equipment investment. Failure to obey the safety rules could result in loss of control of the unit, sever personal injury or death to you, or bystanders, or damage to property or equipment.

  • Page 3: Table Of Contents

    Table of Contents Operator Safety ......... . 2 Operator Safety .

  • Page 4: Operator Safety

    GENERAL WARNINGS • Know the unit’s controls and how to stop quickly. READ THE OPERATOR’S MANUALS. • Read and obey all safety decals. • Only allow responsible adults, who are familiar with the instructions, to operate the unit. • Disengage the PTO. Shut off the engine and wait for all moving parts to stop before attaching, adjusting, or disconnecting any part of the collection system.

  • Page 5: Mowing With The Catcher

    Mowing with the Catcher Always operate with throttle at full speed when mowing. Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging.

  • Page 7: Assembly

    Assembly INSTALL MOUNTING PLATES - BROADMOOR / 1600 / 2600 / LT SERIES Install Plates & Spacers 1. Mount the side brackets (C, Figure 1) to both sides of the frame using the holes shown. Secure with one 3/8-16 x 1 capscrew (D), 3/8 lockwasher (B), and 3/8-16 nut (A) per side.

  • Page 8: Install Baffle And Blade

    Torque Capscrew to 45-55 ft. lbs. (61-75 Nm) Figure 3. Baffle Assembly Install Baffle and Blade Note: Units with an anti-blowout baffle do not require the Clean Sweep baffle. 1. Remove mower deck. See OPERATOR’S MANUAL. 2. Install notched side of baffle (A, Figure 3) to discharge side of deck securing with 5/16-18 x 2 carriage bolt (C) and 5/16-18 locknut (D).

  • Page 9: Install Lower Chute Components

    Install Lower Chute Components INSTALL BRACKET AND PIN ON LOWER CHUTE 1. Secure the puck (C, Figure 6) to lower chute (A) using 5/16-18 x 3/4 capscrew (D) and 5/16-18 locknut (E). 2. Install bracket (F) and deflector prop (G) to lower chute (A) using 5/16-18 x 3/4 capscrews (D) and 5/16-18 locknuts (E).

  • Page 10: Install Bag And Cover Support

    INSTALL BAG AND COVER SUPPORT 1. Install the bag and cover support (B, Figure 7) to upright support (A) using reinforcement plate (C) and 3/8-16 x 1 capscrews (D) and 3/8-16 locknuts (E) as shown. Figure 7. Install Bag and Cover Support A.

  • Page 11: Install Collector Bags

    INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 10). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). Figure 10. Install Collector Bags A. Cover B. Collector Bag C. Grass Bag Hanger D. Bag Hanger Posts INSTALL LOWER DISCHARGE CHUTE 1.

  • Page 12: Install Discharge Tube

    Figure 12. Install Discharge Tube A. Boot B. Discharge Tube C. Seal D. Puck, Metal E. Wire Form F. Slits INSTALL DISCHARGE TUBE 1.Slide discharge tube (B, Figure 12) into seal (C). It may be necessary to lengthen several slits (F) in order for tube (A) to fit into seal (B) 2.

  • Page 13: Normal Removal & Installation

    Normal Removal & Installation of Lower Discharge Chute Note: See previous pages for more detailed installation and operation instructions if necessary. 1. Lift discharge deflector up (E, Figure 13). 2. Slide the notch of bracket (G) on to deflector hinge rod (F).

  • Page 14: Bagger Removal

    Figure 14. Normal Installation & Removal WARNING OPERATION WITHOUT BAGGER For operation without bagger, the mower deflector MUST be properly installed in the down position and retained by the spring latch. Bagger Removal 1. Disconnect the discharge tube (G, Figure 14) from boot (J) by moving wire form (H) up and out from metal puck (I).
  • Page 16 M A N U FA C T U R I N G , I N C . 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com Briggs &...

Table of Contents