Related Manuals for Briggs & Stratton 1695710
Summary of Contents for Briggs & Stratton 1695710
- Page 1 ATTACHMENT OPERATOR’S MANUAL Turboless Triple Bagger Mfg. No. Description 1695710 Triple Bagger - 46” / 52” Mowers 1737726 Rev.: D...
- Page 2 Operator Safety Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed.
- Page 3 Table of Contents / Parts Bag Contents Table of Contents Operator Safety ....Inside Cover Kit Contents ..........4 Assembly ..........5 Operation / Removal / Storage .... 10 Warranty ..........12 2 - CAPSCREW, 3/8”-16 x 1.25” 4 - CARRIAGE BOLT, (Ref.
- Page 4 Kit Contents Kit Contents Ref. Qty. Description Ref. Qty. Description UPPER TUBE UPRIGHT SUPPORT, Assembly MIDDLE TUBE, Clear CARRIAGE BOLT, 1/4”-20 x 1.25” BOOT, Bagging NUT, Conical.1/4”-20 SCREW, 1/4” x .75” NUT, Flange, Nylock, 5/16”-18 COVER ASSEMBLY, Triple Bagger WASHER, .33” ID X 1.25” OD COVER SUPPORT SPACER, Single Step HAIR PIN...
- Page 5 Assembly Install Mounting Spacers - WARNING Conquest / 1700 / 2700 / YT & Prestige / 1800 / 2800 / GT Series Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect Install Spacers the spark plug wire(s).
- Page 6 Assembly Tube & Baffl e Assembly Install Baffl e Hardware Installation For 46” Mower Decks 1. On the left side of discharge opening, insert 1/4”- 1. Lift side discharge chute (A, Figure 7). 20x1.25” carriage bolt (18, Figure 5) through inside of 2.
- Page 7 Assembly Install Tube For 52” Mower Decks 1. Lift side discharge chute (A, Figure 8). Note: Remove and re-assembling hardware may be required. 2. Insert longest baffle (28B) through discharge opening and position baffle inside deck. 1. Ensure latch hardware is in the correct hole for the deck sizes as shown in Figure 9.
- Page 8 Assembly Cover Support Assembly 5. Rotate latch (A, Figure 11) into pocket (B) of hardware assembly (C). 1. Install the bracket and cover support (6, Figure 14) to upright support (A) using 3/8”-16 x 1.0” carriage bolts (9) and 3/8”-16 flange nut (10) as shown. Figure 11 6.
- Page 9 Assembly Cover Assembly Upper & Middle Tube Assembly 1. Attach cover assembly (5, Figure 16) to cover support 1. Slide clear middle tube (2, Figure 17) into upper tube bracket (6) using hinge pivots (A). Secure cover using (1). hinge pins (8) and hair pins (7) as shown. 2.
- Page 10 Operation Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.
- Page 11 Operation Collector Removal CAUTION Operation Without Bagger For operation without bagger, the mower deflector MUST be properly installed in the down position and retained by the spring latch. 1. Lift up cover (5, Figure 19) then remove and empty bags (30). 2.
- Page 12 BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment that is defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of charge, any part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both.
- Page 13 Notes...
- Page 14 Notes...
- Page 16 Copyright © 2011 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved...