Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Skytron ST9 Series
Summary of Contents for Skytron ST9 Series
- Page 1 STELLAR ST9 SERIES EXAMINATION LIGHTS OPERATORS • MAINTENANCE • PARTS REV 8/05...
-
Page 3: Table Of Contents
4. Portable Stand Assembly ......................18 5. Wall Mount Assembly ........................22 Original printing ....... 4/03 Revised ........... 5/04 Revised ........... 8/05 REV 8/05 Although current at the time of publication, SKYTRON'S policy of continuous development makes this manual subject to change without notice. -
Page 4: Equipment Labels And Specifications
Page 2 EQUIPMENT LABELS AND SPECIFICATIONS ATTENTION, CONSULT MANUAL FOR FURTHER INSTRUCTIONS. INDICATES SPECIAL USER ATTENTION. AC VOLTAGE FUSE TYPE 1.75 AMP, FAST ACTING (FA) CLASS I DEFIBRILLATION PROOF, TYPE B EQUIPMENT- IPX4 RATED. INTERNALLY POWERED EQUIPMENT TYPE B EQUIPMENT FOR DRY LOCATIONS UNIT TO BE USED ONLY IN SPECIFIED ENVIRONMENTAL CONDITIONS TEMPERATURE: 15˚... -
Page 5: Model Identification
Page 3 MODEL IDENTIFICATION 70.5" 29" 20˚ 360˚ 360˚ 360˚ 90˚ 320˚ 80" 2030mm ST9W 73" 10.25" 31.5" 260mm 3.75" 20˚ 9" 180˚ 229mm 360˚ 4.75" 360˚ 90˚ 320˚ 121mm 6" 70" 152mm 1778mm ST9S 320˚ 35.5" 360˚ 902mm 50˚ 86.5"... -
Page 6: Section I Operation
Page 4 SECTION I OPERATION Model ST9, Ceiling Mount 1. Turn the power to the light fixture "ON" at 3. When the light is no longer required, turn the the wall switch if applicable. Turn the power to the power to the light "OFF" at the lighthead mounted lighthead "ON"... - Page 7 Page 5 Sterilization 3. When the light is no longer required, turn the Recommended sterilization parameters for optional power to the light "OFF" at the lighthead mounted sterilizable handle: intensity control, return the lighthead to its horizon- a. Prevac, 270° F, 4 minutes tal position against the wall and turn the power b.
-
Page 8: Section Ii Maintenance
SECTION II MAINTENANCE General Semi-Annual (6-months) Maintenance To insure proper operation and extend the life of •Clean diffuser/Filter Assembly your SKYTRON examination lighting system, the following preventive maintenance procedures are • DO NOT operate light without the filter/diffuser in recommended. place. - Page 9 Page 7 Bulb Replacement To replace the Halogen bulb, use the following REFLECTOR procedure: SURFACE BASE 1. Ensure electrical power to the light is "OFF" and the bulb has cooled before changing. 2. Hold the diffuser with one hand, loosen the 1/4 turn screw and lower the diffuser assembly.
-
Page 10: Section Iii Adjustments
Page 8 SECTION III ADJUSTMENTS Check the light fixture axis tension adjustments by moving the lighthead through its full range of travel. WARNING See figure 3-1. All axis should move freely yet maintain any position without drifting. If an adjust- Disconnect electrical power to the ment is required, use the following procedures. -
Page 11: Lighthead Roll Adjustment
Page 9 B. Lighthead Roll Adjustment C. Vertical Travel The vertical travel spring tension is set at the 1. Locate the adjustment hole in the bottom of factory (ceiling and wall mount models) and should the support arm collar. See figure 3-3. not need adjusting. -
Page 12: Lighthead Horizontal Rotation Adjustment
UPPER RADIAL ARM ADJUSTMENT Bulb Voltage ADJUSTMENT The ST9 series is equipped with a voltage compen- HOLE sation device that will deliver the necessary bulb output with a voltage range of between 110VAC LOWER and 120VAC. Routine bulb voltage adjustments... -
Page 13: Section Iv Replacement Parts
Each serviceable part in these exploded views is identified by a reference number. Use this number to locate necessary part information in the parts list adjacent to the exploded view. Always use the complete SKYTRON part number and description when ordering replacement parts. Abbreviations As Required ............ -
Page 14: Ceiling Mount Assembly
Page 12 1. CEILING MOUNT ASSEMBLY st9.0203.001... - Page 15 Page 13 1. CEILING MOUNT ASSEMBLY Item Part No. Description Qty. B5-011-03 SCREW, phillips, M4x10 ..................A/R B4-242-63 COVER, transformer housing ..................1 B4-242-72 TRANSFORMER, 80W, 25V ..................1 B4-242-03 HOUSING, transformer ....................1 B4-020-22 NUT, M4 ........................A/R B4-210-14 WASHER, lock, M4 ....................
-
Page 16: Balance Mechanism Assembly
Page 14 2. BALANCE MECHANISM ASSEMBLY st9.0203.002mj... - Page 17 Page 15 2. BALANCE MECHANISM ASSEMBLY Item Part No. Description Qty. B4-241-06 COVER ........................1 B3-220-16 SCREW, phillips, M4x8 ....................4 B5-010-99 WASHER, flat, M4 ....................... 4 B3-210-04 SLIP RING ........................2 B4-020-39 SCREW, set, M3x4 ...................... 3 B4-242-13 MOUNT, slip ring ......................1 B4-242-11 SNAP RING .........................
-
Page 18: St9 Lighthead Assembly
Page 16 3. ST9 LIGHTHEAD ASSEMBLY st9.0203.003... - Page 19 Page 17 3. ST9 LIGHTHEAD ASSEMBLY Item Part No. Description Qty. B4-020-39 SCREW, set, M3x4 ...................... 1 B9-210-20 KNOB, intensity control ....................1 B4-240-02 INTENSITY CONTROL ASSEMBLY ................1 B4-240-03 SHELL, lighthead ......................1 B9-410-15 SCREW, phillips, M3x25 ..................... 2 B9-410-16 WASHER, flat, M3 .......................
-
Page 20: Portable Stand Assembly
Page 18 4. PORTABLE STAND ASSEMBLY st9.0203.004... - Page 21 Page 19 4. PORTABLE STAND ASSEMBLY Item Part No. Description Qty. B4-241-14 COVER, yoke ......................1 B3-220-16 SCREW, phillips, M4x8 ....................2 B5-010-99 WASHER, flat, M4 ....................... 2 B3-210-04 SLIP RING ........................1 B4-241-13 YOKE, lighthead ......................1 B4-241-12 BEARING BODY ......................1 B5-011-03 SCREW, phillips, M4x10 .....................
- Page 22 Page 20 4. PORTABLE STAND ASSEMBLY (continued) st9.0203.004...
- Page 23 Page 21 4. PORTABLE STAND ASSEMBLY (continued) Item Part No. Description Qty. B4-210-14 WASHER, lock, M4 ....................A/R B4-242-53 SCREW, phillips, M4x12 ..................... 5 B4-242-65 DECAL, fuse type ......................1 B4-242-66 DECAL, caution ......................1 B4-242-67 DECAL, serial number ....................1...
-
Page 24: Wall Mount Assembly
Page 22 5. WALL MOUNT ASSEMBLY st9.0203.005... - Page 25 Page 23 5. WALL MOUNT ASSEMBLY Item Part No. Description Qty. B3-220-16 SCREW, phillips, M4x8 ....................4 B4-242-53 SCREW, phillips, M4x12 ..................... 4 B4-242-54 PLATE, transformer mounting ..................1 B4-220-25 TRANSFORMER, 80W, 25V ..................1 B4-210-14 WASHER, lock, M4 ..................... 4 B4-020-22 NUT, M4 ........................
- Page 28 5000 36th Street S.E., Grand Rapids, MI 49512 1-800-SKYTRON or 1-616-957-0500 • FAX 1-616-957-5053...
Need help?
Do you have a question about the ST9 Series and is the answer not in the manual?
Questions and answers