Motorline professional MC62 User's And Installer's Manual
Control board
Hide thumbs
Also See for MC62:
- User's and installer's manual (17 pages) ,
- User's and installer's manual (18 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Motorline professional MC62
Summary of Contents for Motorline professional MC62
- Page 1 MC62 MC62 USER’S AND INSTALLER’S MANUAL v1.4 REV. 07/2021...
-
Page 2: Table Of Contents
00. CONTENT 00. CONTENT INDEX INDEX 01. SAFETY INSTRUCTIONS 07. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS / TECHNICIANS 02. CONTROL BOARD 08. CONEXION SCHEME CHARACTERISTICS CONEXIONS MAP RECOMMENDATIONS PRIOR TO PROGRAMMING 03. INSTALLATION BASE INSTALLATION PROCESS TRANSMITTERS FUNCTIONS P MENUS E MENUS 04. -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS 01. SAFETY INSTRUCTIONS ATTENTION: GENERAL WARNINGS • This manual contains very important safety and usage information. This product is certified in accordance with European very important. Read all instructions carefully before beginning Community (EC) safety standards. the installation/usage procedures and keep this manual in a safe place that it can be consulted whenever necessary. - Page 4 01. SAFETY INSTRUCTIONS 01. SAFETY INSTRUCTIONS • Children shouldn’t play with the product or opening devices from the ground or other level of access, the minimum safety to avoid the motorized door or gate from being triggered • and health requirements for the use of work equipment workers involuntarily.
-
Page 5: Control Board
01. SAFETY INSTRUCTIONS 02. CONTROL BOARD CHARACTERISTICS The MC62 is a control board with built-in radio control system, developed for the in in motion, and do not create strength to the gate movement. automation of 24V swing gates. • Do not perform any operation on mechanical elements or hinges if the product is in motion. -
Page 6: Installation
02. CONTROL BOARD 03. INSTALLATION CHARACTERISTICS BASE INSTALLATION PROCESS 01 • Full Pulsing Input (NO) The installation process assumes that the gate already has mechanical or 02 • Common electrical limit switches installed. For more information read the motor's manual 01 •... -
Page 7: Transmitters 7A
03. INSTALLATION 03. INSTALLATION TRANSMITTERS FUNCTIONS Transmitter programming for total opening. Transmitter programming for pedestrian opening. We can only go into programming with the gate electrically stumbled. • PROGRAMMING TRANSMITTERS • ERASE TRANSMITTERS The functions of the plant are divided into 2 areas: •... -
Page 8: P Menus 8A
03. INSTALLATION 03. INSTALLATION P MENUS E MENUS MAX. MIN. FACTORY MAX. MIN. FACTORY MENU FUNCTION STATE PAGE MENU FUNCTION STATE PAGE PROGRAMMABLE VALUE PROGRAMMABLE VALUE Desactivates present man Manual Programming Activates present man Course Programming 1 motor Disables push buttons mode 2 motors Activates push buttons mode Present Man... -
Page 9: Programming "P
04. PROGRAMMING "P" 04. PROGRAMMING "P" COURSE PROGRAMMING DECELERATION TIME ADJUSTMENT This menu allows to set the deceleration time of each leaf at opening and closing. Programmation Motors This menu allows automatic motor and This menu allows you to program whether the relaxation programming. -
Page 10: P3-Pedestrian Course Time 10A
04. PROGRAMMING "P" 04. PROGRAMMING "P" FORCE AND SENSIBILITY ADJUSTMENT PAUSE TIME AND DOORS DELAY 01 • Press MENU for 2 sec. until it appears 01 • Press MENU for 2 sec. until it appears 02 • Use UP until appears 02 •... -
Page 11: P6-Photocells 2 Programming 11A
04. PROGRAMMING "P" 04. PROGRAMMING "P" PHOTOCELLS 2 PROGRAMMING OPERATING LOGIC 01 • Press MENU for 2 sec. until it appears Allows to program le security behavior (photocell 2). 02 • Use UP until appears 03 • Press Menu will appear 04 •... -
Page 12: Programming "E
04. PROGRAMMING "P" 05. PROGRAMMING "E" REMOTE PROGRAMMING SOFT START 01 • Press MENU for 2 sec. until it appears 00 off 02 • Use UP until appears 01 active 03 • Press Menu will appear Enables or disables the soft start. With the soft start function activated, at each start of move- 04 •... -
Page 13: E4-Course Time Adjustment
05. PROGRAMMING "E" 05. PROGRAMMING "E" FOLLOW ME BRAKE/LOCK/PUSH 00 function disabled Allows to program gate behavior 01 function activated after opening 02 function activated on opening 00 (disables 00 (active lock on 00 (disable opening 00 (disables closing 00 (disables engine Allows you to activate the Follow me option. -
Page 14: E7-Manuevers Counter
05. PROGRAMMING "E" 05. PROGRAMMING "E" MANUEVERS COUNTER RESET - RESET FACTORY VALUES This menu allows you to view the number of maneuvers performed. (complete maneuver means opening and closing). When you reset, all factory values will be reset and all commands will be erased. -
Page 15: Display
06. DISPLAY DISPLAY INDICATIONS MENU DESCRIPTION MENU DESCRIPTION In the still position, fully open All commands erased In the still position, intermediate position Command triggered from the indicated position In the still position, fully closed Obstructed photocell Full opening button pressed Obstructed photocell Pedestrian opening button pressed In pause time... -
Page 16: Troubleshooting
07. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS / TECHNICIANS Anomaly Anomaly Procedure Procedure Behavior Behavior Procedure II Procedure II Discovering the origin of the problem Discovering the origin of the problem • Make sure you • Make sure you 1 • Open control box and check if 1 •... -
Page 17: Conexion Scheme Conexions Map
08. CONEXION SCHEME CONEXIONS MAP...
Need help?
Do you have a question about the MC62 and is the answer not in the manual?
Questions and answers