01. SAFETY INSTRUCTIONS Dit product is gecertificeerd in overeenstemming met de WAARSCHUWINGEN ALGEMEEN veiligheidsnormen van de Europese Commissie (“EC”). • Deze handleiding bevat zeer belangrijke veiligheids- en gebruiksinformatie. Dit product voldoet aan Richtlijn 2011/65/EU van het Europees ZEER BELANGRIJK. Lees alle instructies zorgvuldig door voor u met de Parlement en de Raad, van 8 juni 2011, betreffende beperking installatie/gebruik procedures begint en bewaar deze handleiding op van het gebruik van bepaalde gevaarlijke stoffen in elektrische...
Page 4
01. SAFETY INSTRUCTIONS • Als de voedingskabel beschadigd is, moet deze worden vervangen door buizen leiden, om ze te beschermen tegen mechanische invloeden, in de fabrikant, de after-sales service of vergelijkbaar gekwalificeerd het bijzonder de voedingskabel. Let erop dat alle kabels van onderaf personeel om gevaar te voorkomen.
01. SAFETY INSTRUCTIONS 02. CONTROL BOARD TECHNICAL SPECIFICATIONS • Indien het systeem moet worden gerepareerd of aangepast, ontgrendel dan het apparaat, schakel de stroom uit en gebruik het niet totdat aan The MC50SC is a monophasic control board com a control system via incorporated rádio, developed for the automation of sliding gates and sectional doors.
02. CONTROL BOARD 03. INSTALLATION PROGRAMMING PRE-RECOMENDATIONS INSTALLATION OF MCONNECT LINK (OPTIONAL) Dipper To enhance knowledge about the control board operation, before proceeding to the setup, give special attention to the instructions that follow. LO FA FC LA LE 3 4 5 1 2 3 4 5 LS •...
03. INSTALLATION 03. INSTALLATION ESSENTIAL STEPS FOR INSTALLATION REMOTE CONTROLS Programming a remote control for full opening. The installation process assumes that the gate has already limit switches plates installed. For more information consult the motor's manual. Programming a remote control for pedestrian opening. •...
03. INSTALLATION 03. INSTALLATION "P" MENU FUNCTIONS "E" MENU FUNCTIONS • To access the E menu press the MENU button for 10sec. FACTORY • Use ↓↑ to navigate through the menus. MENU FUNCTION MIN. MAX. STATE PAGE VALUE MENU • Press MENU when you want to confirm access to a menu. ↑...
04. PROGRAMMING "P" 04. PROGRAMMING "P" AUTOMATIC AND SEMI-AUTOMATIC COURSE PROGRAMMING AUTOMATIC AND SEMI-AUTOMATIC COURSE PROGRAMMING This menu allows automatic programming of the motor and deceleration. With this menu you can change the direction of the motor's movement, without change the connection of the motor wires and limit switches.
04. PROGRAMMING "P" 04. PROGRAMMING "P" FORCE AND SENSITIVITY ADJUSTMENT PAUSE TIME Total closing pause time adjustment It allows you to adjust the motor sensitivity Factory values Allows you to set the waiting time for the gate from when it finishes fully in detecting obstacles.
04. PROGRAMMING "P" 04. PROGRAMMING "P" SAFETY EDGE OPERATING LOGIC 00 (disables safety edge) 01 (activates safety edge) Factory values This menu allows you to set the gate's operating mode. SC, BR, SE: 00 The menu allows you to activate/deactivate its operation. Functioning in automatic mode 00 (8k2 input) 01 (NC input) 1st impulse - OPENS...
04. PROGRAMMING "P" 05. PROGRAMMING "E" FLASHING LIGHT HUMAN PRESENCE 01 • Press MENU for 3 seconds. 02 • P0 appears. Press ↓ eight times. Deactivates human presence 03 • P8 appears. Press MENU for 1 second. 04 • Appears the function currently set. If you want, change the function to 00, 01, 02 or 03, using ↓↑. Factory values Ascent and descent in Human Presence SC, BR, SE: 00...
05. PROGRAMMING "E" 05. PROGRAMMING "E" COURTESY LIGHT TIME/PRE-FLASHING LIGHT ELECTRIC BRAKE With the electronic brake, whenever the gate stops, or is given an order to This menu is only available if the Courtesy Light function is active in menu P8 (see page 11A). Factory values reverse the movement, the advance decreases, counteracting the inertia exerted SC, BR, SE: 00...
05. PROGRAMMING "E" 06. DISPLAY RESET - RESTORE FACTORY VALUES DISPLAY INDICATIONS By doing reset, all factory settings will be restored. Factory values MENU DESCRIPTION SC, BR, SE: 00 Only the maneuvers counter will have the data memorised. Motor opening 01 •...
07. COMPONENTS TEST CAPACITOR SCHEME To detect which components have problems during automatism installation, sometimes it's necessary to conduct tests with a direct connection to a 110/230V power supply. For this, it's necessary to interpose a capacitor on the connection so that the motor can work (check the capacitor type to be used in the product's manual). In the below diagram is shown how this connection must be made and how to merge the different component wires.
09. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS/TECHNICIANS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem 1 • Open control box and check if 3 • Switch off the control 4 • If the motor works, the 5 • If the motor doesn’t work, •...
Need help?
Do you have a question about the MC50 and is the answer not in the manual?
Questions and answers