Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Motorline professional SIGMA 4M
Summary of Contents for Motorline professional SIGMA 4M
- Page 1 SIGMA SIGMA USER / INSTALLER'S MANUAL v1.0 REV. 12/2019...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS INDEX ATENTION: 01. SAFETY INSTRUCTIONS This product is certified in accordance with European Community (EC) safety standards. 02. AUTOMATISM TECHNICAL CHARACTERISTICS This product complies with Directive 2011/65/EU of the KIT COMPONENTS European Parliament and of the Council, of 8 June 2011, on LIGHT FLASHLIGHT the restriction of the use of certain hazardous substances in LOCK / UNLOCK AUTOMATISM... - Page 3 01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. very important. Read all instructions carefully before beginning the WARNINGS FOR TECHNICIANS installation/usage procedures and keep this manual in a safe place that it can be consulted whenever necessary.
- Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY September 2009. • Attach the permanent label for the manual release as close as possible • Supplier disclaims any liability if: to the release mechanism. • Product failure or deformation result from improper installation • Disconnect means, such as a switch or circuit breaker on the electrical use or maintenance! panel, must be provided on the product’s fixed power supply leads in •...
-
Page 5: Automatism
02. AUTOMATISM 02. AUTOMATISM TECHNICAL CHARACTERISTICS KIT COMPONENTS You should check if the following items are in the automatism package before you start the installation. SIGMA is an electromechanical barrier designed to control vehicle access to private, industrial or commercial areas. •... -
Page 6: Light Flashlight 5A
02. AUTOMATISM 02. AUTOMATISM LIGHT FLASHLIGHT LOCK / UNLOCK AUTOMATISM This barrier has two RGB flashlights integrated in the top cover, for emission of red, green and blue In an emergency or during the barrier installation / adjustment phase, it may be necessary to move colors. -
Page 7: Installation
03. INSTALLATION INSTALLATION MAP 1 • Sigma 9 • Barrier Cover 2 • Bar 10 • Transformer 3 • Bar Extension 11 • Unlocker 4 • Photocell support column (not included) 12 • Motor 5 • Photocell 13 • Spring(s) 6 •... -
Page 8: Remove Cover And Profiles 7A
03. INSTALLATION 03. INSTALLATION REMOVE COVER AND PROFILES SHOE CREATE SHOE This barrier allows free access to the interior to facilitate the product installation and maintenance • process. To do so, remove the aluminum cover and profiles from the barrier. Drill a hole of 355x470mm and 400mm (or greater) deep to create the fixing shoe. -
Page 9: Automatism Installation
03. INSTALLATION AUTOMATISM INSTALLATION Mount the bolts and screws to the mounting Route the electrical cables to connect the engine to the accessories and power supply. Leave cables plate as exemplified in step of a length that ensures easy connection to the control panel at the top of the barrier. Position the barrier on the plate leaving it centered and secure it by tapping the screws inside the barrier. -
Page 10: Bar Position
03. INSTALLATION 03. INSTALLATION BAR POSITION INVERTER POSIÇÃO DA HASTE LEFT BAR RIGHT BAR • • If the motor and springs are on the opposite side as intended, according to the diagrams on the left page, you should change the position of these components before placing the bar in the barrier. -
Page 11: Invert Bar Position
03. INSTALLATION INVERT BAR POSITION INVERT MOTOR APPLY SPRINGS • • Unlock the motor (page 5B). Loosen the screw that secures the motor tip to the lever as well as washers and socket. Remove the motor fixation bolt to the bottom plate A ·... -
Page 12: Bar Mounting
03. INSTALLATION BAR MOUNTING Fit the remaining pieces in the order shown in the picture. Route the cable that comes out of the barrier shaft through the hole in the assembly you REVERSE BAR SUPPORT • assembled. Secure the parts to the stem clamping plate with screws and bolts provided in the package. Make the connection between the cable that goes out through the barrier shaft and the LED cable on the bar. -
Page 13: Fix Bar Supports
03. INSTALLATION FIX BAR SUPPORTS SET EXTENDING BAR LENGTH ADJUSTING SUPPORT (FIXED) HEIGHT • • If the height of the support arm is misaligned to the height of the bar you will have to adjust the arm You should now set its length so that you can then place the support as shown in the image below. height. -
Page 14: Adjust The Springs
03. INSTALLATION ADJUST THE SPRINGS Before adjusting the springs, manually place the bar in the upright position (motor extended) so that the Hold the threaded bar with pliers so that it springs are in the lowest tension position, and lock the motor in this position. does not rotate, and then tighten the adjusting female until each spring is stretched the distance mentioned in the table on page 14. -
Page 15: Adjusting Tables
03. INSTALLATION ADJUSTING TABLES LEVER HOLES 6M BAR • • Hole 3 Hole 2 Hole 1 SIMPLE BAR 6000 5500 5000 4500 4000 3500 Hole: Hole 3 Hole 3 Hole 2 Hole 2 Hole 3 Hole 3 SPRING 1 (Big) 2 mm 25 mm 5 mm... -
Page 16: Testing Spring Adjustment
03. INSTALLATION 03. INSTALLATION TESTING SPRING ADJUSTMENT ADJUSTING LIMIT SWITCHS The mechanical limit switches present in the barrier are visible in the image below. • They consist of 2 adjusting screws (one on each side of the barrier) fixed to the bar movement lever. The motor must remain unlocked to perform the tuning test. -
Page 17: Power Cable
03. INSTALLATION POWER CABLE *The barrier frame has a tube located on the inside so that it can conduct power wiring to the connectors (top of the barrier). Route the power cables coming from the ground through the pipe. When the power cable reaches the barrier surface, connect the wires to the connector on the electronics support plate. -
Page 18: Apply Profiles And Cover
03. INSTALLATION APPLY PROFILES AND COVER APPLY PROFILES • Position the BACK PROFILE in the correct location (profile previously placed for rod application). Holding the BACK PROFILE so that it does not dislocate, fit the SIDE PROFILES into the barrier frame. -
Page 19: Connections
04. CONNECTIONS ENGINE AND FLASHING LIGHT CONNECTIONS • RGB module and MP106 module inside 24AC LOCK FCH PUL + BAT - LAMP • Control board MC61 BR (Barrier Interior) • Transformer • Limit Switch • SIGMA • MP106 module Barrier LGHI 12V+ GI RGI... -
Page 20: Photocell Connections And Safety Band
04. CONNECTIONS PHOTOCELL CONNECTIONS AND SAFETY BAND WITHOUT SAFETY BAND WITH SAFETY BAND (SERIAL CONNECTION) • • • LED strip (bar) • Security Band (Optional) • Control board LOCK FCH PUL 24AC LOCK FCH PUL • Control board MC61 + BAT - LAMP MC61 BR (Barrier BR (Barrier Interior) -
Page 21: Troubleshooting
05. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS / SPECIALIZED TECHNICIANS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem 1 • Remove the barrier top cover; • Barrier • Make sure you have • Still not working • Consult a qualified 2 •...
Need help?
Do you have a question about the SIGMA 4M and is the answer not in the manual?
Questions and answers