SGM LB-100 Manual

SGM LB-100 Manual

Led balls
Hide thumbs Also See for LB-100:

Advertisement

Quick Links

LB·100
LED BALLS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LB-100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SGM LB-100

  • Page 1 LB·100 LED BALLS...
  • Page 2 Dimensions of LB-100 LED Balls All dimensions in mm. Drawing not to scale.
  • Page 3 The SGM logo, the SGM name and all other trademar s in this document pertaining to ser ices or products by SGM or its af liates and subsidiaries are trademar s o ned or licensed by SGM or its af liates or subsidiaries.
  • Page 4: Table Of Contents

    Contents Safety Information....................5 Read the Manual..............................6 Protection from Injury............................6 Introduction..........................7 Parts Identi cation and erminology........................Features..............................8 Connections Overview............................9 Connecting to M ouring D Driver ....................sing custom ower su ly and M ada tor ca le..................Service..........................12 Cleaning..............................Troubleshooting......................13 Speci cations -100 00 0001 ................14 Users notes........................16...
  • Page 5: Safety Information

    • Verify that the power feed cable is rated for the current draw of all connected tures. See application informa- tion on page 11. • Do not modify the ture or install other than genuine SGM parts. • Do not operate the system if the ambient air temperature Ta e ceeds 40 C 104...
  • Page 6: Read The Manual

    D alls, and follow the safety precautions. Always observe all warnings in this manual and printed on the system. If you have questions about how to oper- ate the system safely, please contact your SGM representative. Protection from injury • nsure that any structure used for support as well as all fastened and connected hardware can hold at least 10 times the weight of all supported devices and equipment.
  • Page 7: Introduction

    Introduction Part identi cation and terminolo y See ig. 1 for part terminology and identi cation. ne string D alls 7 D balls ne row of D alls consisting of 1 to strings Ma . 56 D balls . Fig.
  • Page 8: Features

    Features The SGM D alls form a modular semi-transparent D video curtain with a 12cm pi el pitch, which can be viewed in a 360 angle. D all driver is capable of producing a seamless image of 6.6 meters vertically and for as long in the hori ontal direction as the number of drivers permit ig.2 .
  • Page 9: Connections Overview

    Connections Overview D ball string has a female 4 pin RJ765 connector at the inlet before ball 1 , and a male 4 pin RJ765 con- nector at the outlet after ball 7 . ig. 3 shows the pin layout. pin female R 6 connector Connector front shown...
  • Page 10 onnectin to Tourin ri er T D-612 0070201...
  • Page 11 ustom o er su ly and G ada tor ca le When e tending the supply cable between the adaptor 3060201 and a user speci ed 12VDC SU, make sure to use cables according to speci cations in the table below. When using a 12V DC custom power supply, it must be protected with a T12.5A fuse.
  • Page 12: Service

    This procedure will allow you to assess cleaning requirements in your particular situation. If in doubt, consult your SGM dealer for a suitable maintenance schedule. Clean the D alls with a soft cloth dampened with a solution of water and a mild detergent such as car shampoo.
  • Page 13: Troubleshooting

    Troubleshooting Problem Probable cause(s) Remedy No DMX signal is Replace DMX source received from source Check addresses and protocol settings No light in Defective DMX source Replace DMX source D ball Incorrect addressing Check addresses and protocol settings Defective Replace D string Replace DMX source Defective DMX source...
  • Page 14: Speci Cations

    Speci cations (Part BALL DIMENSIONS Diameter...............................2 mm i el pitch................................12cm 7 balls string length alls CC ..........................72cm i el weight..............................20g INSTALLATION Orientation............................Any AMBIENT OPERATING CONDITIONS Ma imum ambient temperature T ....................40 °C 104 ° Minimum ambient temperature T ....................-10 °C 14 ° Operating humidity..............................100% I rating................................I 65 SIGNAL SOURCE...
  • Page 15: 100 Art 00 0001

    CONNECTIONS Data input........................Male locking 4 pin RJ765 socket Data output......................emale locking 4 pin RJ765 socket ELECTRICAL ower supply voltage..........................12V -0.2V ower consumption per -100 7 pi els ......................5.4W APPROVALS Safety................................ N 60 50-1 MC............................. N 55103-1, N 55103-2 INCLUDED PARTS •...
  • Page 16: Users Notes

    Users notes...
  • Page 20 SGM A/S · Soeren Frichs Vej 51-53 · DK 8230 Aabyhoej · Denmark Tel +45 70 20 74 00 · info@sgmlight.com · www.sgmlight.com...

Table of Contents