Subscribe to Our Youtube Channel
Related Manuals for SGM X-5
Summary of Contents for SGM X-5
- Page 1 X·5 / XC·5 LED STROBE...
- Page 2 X·5 / XC·5 LED Strobe dimensions All dimensions in mm. Drawing not to scale.
- Page 3 The SGM logo, the SGM name and all other trademarks in this document pertaining to services or products by SGM or its affiliates and subsidiaries are trademarks owned or licensed by SGM or its affiliates or subsidiaries.
-
Page 4: Table Of Contents
Contents Safety Information....................5 Preparation for Use....................7 Controller Operation....................9 Setup......................10 DMX Control Summary...................12 Service......................14 DMX Protocols......................15 Specifications..................20 Users notes ........................ -
Page 5: Safety Information
Safety Information WARNING! This product is for professional use only! It is not for household use. Strobe lights are known to trigger epileptic seizures in persons who are photosensitive. To guard against electric shock. • Do not open: there are no user-serviceable parts inside. •... - Page 6 • Provide a minimum clearance of 0.1 meters (4 inches) around air vents. • Do not modify the fixture or install other than genuine SGM parts. • Do not operate the fixture if the ambient air temperature (Ta) exceeds 40˚ C (104˚ F).
-
Page 7: Preparation For Use
The auto-ranging power supply automatically adjusts to AC power from 200-240 volts nominal at 50/60 Hz. The current required by the X-5/XC-5 is 4 amps. To avoid overload, allow one 4 amp branch circuit per fixture to operate the X-5/XC-5 model at full power. - Page 8 To rig the fixture Always use a secure means of secondary fixing such as a safety wire Before installing, verify that; • the attachment hardware is in good condition and designed to carry at least 10 times the fixture’s weight, •...
-
Page 9: Controller Operation
Data Connection The X-5/XC-5 provided 5-pin XLR sockets for data connection. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5. The sockets are wired in parallel: both inputs connect to both outputs. -
Page 10: Setup
Setup The fixture uses an interactive display for setting up DMX address and operation mode. Use the five buttons next to the display to navigate the setup structure (Fig. 1). Operation Data mode indicator Fig. 1 Fig. 2 Data Address protocol When the product is switched on, the fixture will be at its default setting showing the ROOT menu (Fig. - Page 11 Setting DMX address In the root menu the user can set the DMX address directly by using the arrow UP and DOWN (Fig. 3). Fig. 3 The fixture has a handy feature which displays the DMX value for the next fixture (assuming you are connecting more than one fixture) The selected address is stored by pushing ENTER storing the DMX address.
-
Page 12: Dmx Control Summary
(where it is always at maximum intensity). A special pixel mode enables the fixture to be used as a blinder, where the intensity of blinder colour (XC-5 models) or each of three pixel segments (X-5 models) can be set. Duration Flash duration can be set from 0 to 650 ms on 50 Hz power supplies, or 0 to 530 ms on 60 Hz power supplies in 3, 4, 6 or 7 channel DMX modes. - Page 13 • Ramp up: Light gradually increases in intensity, then blacks out. • Ramp down: Light flashes to full intensity, then gradually fades. • Ramp up-down: Light gradually increases and decreases. • Random flash: Light flashes randomly with variable rate and intensity. Multiple units flash independently of each other. •...
-
Page 14: Service
Fuse Replacement The X-5/XC-5 uses a time-delay fuse for protection against current overload. The fuse is located inside the base on the main PCB of the fixture – next to the low voltage power supply. Fuses must be replaced by a certified professional. -
Page 15: Dmx Protocols
DMX Protocols 1 channel mode Channel Value Percent Function Blackout 6-249 2-97 Flash rate, slow to fast 250-255 98-100 Continuous blinder effect 3 channel mode Channel Value Percent Function Blackout 6-255 2-100 Flash intensity - minimum to maximum Flash duration: 0-255 0-100 0-650 ms @ 50 Hz AC... - Page 16 4 channel mode Channel Value Percent Function Blackout 6-255 2-100 Flash intensity - minimum to maximum Flash duration: 0-255 0-100 0-650 ms @ 50 Hz AC 0-530 ms @ 60 Hz AC No flash (trigger single flash using channel 1) Flash rate: 6-255 2-100...
- Page 17 6-255 2-100 Flash intensity - minimum to maximum Blackout Red blinder intensity (XC-5 models), or 6-255 2-100 Segment 1 intensity (X-5 models) Blackout Green blinder intensity (XC-5 models), or 6-255 2-100 Segment 2 intensity (X-5 models) Blackout Blue blinder intensity (XC-5 models), or...
- Page 18 6-255 2-100 Flash intensity - minimum to maximum Blackout Red blinder intensity (XC-5 models), or 6-255 2-100 Segment 1 intensity (X-5 models) Blackout Green blinder intensity (XC-5 models), or 6-255 2-100 Segment 2 intensity (X-5 models) Blackout Blue blinder intensity (XC-5 models), or...
- Page 19 Channel Value Percent Blinder intensity Blackout Red blinder intensity (XC-5 models), or 6-255 2-100 Segment 1 intensity (X-5 models) Blackout Green blinder intensity (XC-5 models), or 6-255 2-100 Segment 2 intensity (X-5 models) Blackout Blue blinder intensity (XC-5 models), or...
-
Page 20: Specifications
Specifications X·5 (Part #: 80090001) XC·5 (Part #: 80090002) PHYSICAL Size (without bracket)………..............………………………… 268 x 500 x 120 mm Weight…………………………………………………………............……..……5.8 kg THERMAL Maximum ambient temperature……………………………...............40° C (104° F) CONTROL AND PROGRAMMING USITT DMX512-A control………........1, 3, 4, 6, and 7 channel modes, pixel mode (3 channels) AC POWER AC input……………………………………………………………..............Powercon Approved AC power (EU)………………….............200 - 240 V nominal, 50/60 Hz... - Page 21 CONSTRUCTION Housing……………………………………………………………..........Aluminium Finish…………………………………………..............Electrostatic powder coating INSTALLATION Minimum clearance around fan and air vents…………………..............0.1 m (4 in) Specifications subject to change without notice...
-
Page 22: Users Notes
Users notes...
Need help?
Do you have a question about the X-5 and is the answer not in the manual?
Questions and answers