Subscribe to Our Youtube Channel
Related Manuals for Lincoln SKF J Series
Summary of Contents for Lincoln SKF J Series
- Page 1 Installation instructions Air-operated chassis pump Model 83513, series “J” Date of issue June 2020 Form number 403513 Version...
-
Page 2: Table Of Contents
Contents EC Declaration of Incorporation Safety Explanation of safety signals Description Specifications Dimensions Installation Typical system hookup Accessories Pressure relief procedure Operation Inspect before use Pump use Lubrication Lubricate air valve mechanism Material restriction prevention Corrosion prevention Disassembly Assembly Troubleshooting Repair Service parts Illutrated parts breakdown... -
Page 3: Ec Declaration Of Incorporation
EC Declaration of Incorporation Manufacturer: SKF 5148 N. Hanley Road St Louis, MO U.S.A. URL: SKF.com Phone: 314-679-4200 EU Contact:SKF Heinrich-Hertz-Straße 2-8 69190 Walldorf Phone: 59 (0) 6227-33259 Product: Series 20 pump Description: Air driven grease and oil pumps Model(s): 83513, Year of construction: see type identification plate complies with all basic requirements of the following directives at the time when first being launched in the market. -
Page 4: Safety
Safety Explanation of safety signals Read and understand all warnings, cautions and instructions before operating equipment. NOTE • Extreme caution should be used when Emphasizes useful hints and operating equipment as personal injury recommendations as well as and/or property damage can result from information to prevent property damage equipment misuse. -
Page 5: Description
Description Table 1 Specifications Air motor effective diameter 2.5 in (63.5 mm) Model 83513 is an air operated chassis Air inlet in NPTF pump designed to pump low and medium Material outlet in NPTF viscosity materials (grease) from drums Ratio 50:1 and pails. -
Page 6: Dimensions
Fig 1 Dimensions 6 in (152 mm) (71 mm) (81 mm) (73 mm) 4 in (101 mm) 11 in (279 mm) NPTF in – 20 (19 mm) (46 mm) (57 mm) (479 mm) Ø 1 in (25 mm) Air inlet. Lubricant outlet. -
Page 7: Installation
• Eyebolt kit installing a system. • Follower plate 120 lb. (54 kg), Contact Lincoln factory representative for 400 lb. (181 kg) assistance in designing system for specific • Drum cover 120 lb. (54 kg), requirement. -
Page 8: Pressure Relief Procedure
Pressure relief Pump use 7 Stop pump immediately if accelerates quickly or is running too fast. Check procedure 1 To start pump, turn on main air supply. grease supply and refill if necessary. 2 Slowly open air regulator. Regulate air 7 1 Circulating systems: pressure from 20–40 psi (1.4–2.8 bar) Pump runs continuously and slows... -
Page 9: Lubrication
Perform pressure Air line filter/regulator is recommended for relief procedure prior to starting pump. use with Lincoln pump to remove harmful Flush system as required with a compatible Failure to comply may result in death dirt and moisture from compressor air solvent to prevent material buildup when or serious injury. -
Page 10: Disassembly
Disassembly NOTE Lubricate air cylinder and air piston rod before assembly to prevent damage to 1 Remove valve cap (12) and trip rod air piston packing and pump gland pin (11). packing. Thread piston rod through 2 Unscrew four nuts (64) from tie rods (65) gland packing when assembling pump. -
Page 11: Troubleshooting
Special procedures and tools service center. When submitting equipment are required. Contact Lincoln Customer to be repaired, be sure to state the nature Service, 5148 North Hanley Road, St. Louis, of the problem and indicate if a repair cost MO 63134, (314) 679-4200 for your nearest estimate is required. -
Page 12: Service Parts
Service parts Item number Description Quantity Part number Item number Description Quantity Part number Air motor piston rod 11340 Coupling stud 11346 Air piston bolt 11329 Ball stop 57027 Air piston washer 48212 Check Ball 69102 1) 3) Air piston packing 34090 Plunger and bushing assembly 1 90554... -
Page 13: Illutrated Parts Breakdown
Fig IPB 1 Use Locktite 510 gasket eliminator on threads. Tighten to 10–15 lbf-ft. (13–20 Nm). To make compatible with synthetic greases, refer to Synthetic grease kit 245530.* Indicates change. -
Page 14: Synthetic Grease Kit 245530
Fig IPB 2 Description Part number Weight Length lbs. Bare pump 83513 – – – Piston rod 11799 – – Pump tube 61293 – – 29/ 32 Drum size – – – Dimension A – – – Synthetic grease kit 245530* Converts pump to be compatible with synthetic greases and lubricants. - Page 15 Fig IPB 3 in NPTF Air exhaust port. Lubricate balls and springs before assembly. Tighten to 30–40 lbf-in. (3.3–4.5 Nm). Tighten to 90–100 lbf-in. (10 to 11 Nm). Air valve mechanism. Lubricant outlet. Do not exceed 15 lbf-ft. (20 Nm). Optional eyebolt kit for hoisting purposes.
-
Page 16: Warranty
| lincolnindustrial com ® SKF, Lincoln and PowerMaster are registered trademarks of the SKF Group. © SKF Group 2020 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted.
Need help?
Do you have a question about the SKF J Series and is the answer not in the manual?
Questions and answers