Table of Contents
Advertisement
Quick Links
Exabyte Field Instruction
September 2003
I
NSTALLING OR
IN THE
L
1006159-001
#1006159-001#
R
E
110L A
XABYTE
,
IBRARY
OR
1
B
Y
B
EFORE
OU
EGIN
2
R
S
EMOVING THE
ERVICE
(221L
221L-Fc) . . . . . . . . . . . . . . . . . . . . . . . 4
OR
3
R
T
EMOVING THE
APE
4
I
N
NSTALLING THE
5
R
O
ESUMING
EPLACING A
UTOLOADER
221L-FC L
C
ONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . 2
A
C
CCESS
OVER
D
. . . . . . . . . . . . . . . . . . 5
RIVE
T
D
. . . . . . . . . . . . . . 7
EW
APE
RIVE
. . . . . . . . . . . . . . . . . . . . . . 8
T
D
APE
RIVE
, 221L
IBRARY
Advertisement
Table of Contents
Related Manuals for Exabyte 110L LTO Ultrium AUTOLOADER
Summary of Contents for Exabyte 110L LTO Ultrium AUTOLOADER
- Page 1 Exabyte Field Instruction September 2003 NSTALLING OR EPLACING A RIVE 110L A , 221L IN THE XABYTE UTOLOADER 221L-FC L IBRARY IBRARY ONTENTS ......2...
- Page 2 OPYRIGHT Copyright 2000 - 2003 by Exabyte Corporation. All rights reserved. This item and the information contained herein are the property of Exabyte Corporation. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the express written permission of Exabyte Corporation, 1685 38th Street, Boulder, Colorado 80301.
- Page 3 If you are upgrading a 221L library from SCSI to Fibre Channel Important or from Fibre Channel LTO Ultrium 1 to Fibre Channel LTO Ultrium 2, contact Exabyte Technical Support (1-303-417-7792) to determine whether your library needs additional hardware upgrades.
- Page 4 (221L 221L-FC) EMOVING THE ERVICE CCESS OVER (221L 221L-FC) EMOVING THE ERVICE CCESS OVER If you are installing an additional tape drive in the 221L or 221L-FC library, follow these steps to remove the drive bay service access cover. If you are replacing a tape drive, skip to the following section,”Removing the Tape Drive.”...
- Page 5 EMOVING THE RIVE EMOVING THE RIVE If you are replacing an existing tape drive, follow these steps to remove the drive: 1. 1. 1. 1. Disconnect the cable(s) and terminator, if present, from the back of the tape drive you are replacing. The connectors for the tape drives are accessible from the back panel (see Figure 2 for the 221L connectors and...
- Page 6 EMOVING THE RIVE 2. 2. 2. 2. From the back panel, use a #2 Phillips screwdriver to release the captive screw that secures the tape drive carrier to the library or autoloader (see Figure Handle Captive screw Figure 4 Loosening the captive screw securing the tape drive to the library (221L shown) 3.
- Page 7 NSTALLING THE RIVE NSTALLING THE RIVE 1. 1. 1. 1. Insert the tape drive so that the handle is at the left and the fan is at the bottom, as shown in Figure 5. The tape drive should slide easily toward the front of the library.
- Page 8 § Is the library or autoloader operating in the correct control mode? (For most applications, the control mode should be set to SCSI.) If you cannot solve the problem yourself, contact your service provider or Exabyte Technical Support (1-303-417-7792). 2003 1006159 EPTEMBER...
Need help?
Do you have a question about the 110L LTO Ultrium AUTOLOADER and is the answer not in the manual?
Questions and answers