Download
Share
Print this page
  1. Manuals
  2. Brands
  3. HunterDouglas Manuals
  4. Indoor Furnishing
  5. PowerView M25T
  6. Manual

HunterDouglas PowerView M25T Manual

Roller blind 18vdc tubular motor
Hide thumbs Also See for PowerView M25T:

Advertisement

Quick Links

Download this manual
MANUAL
Safety instructions
The motor may only be operated after reading these safety instructions, failing to do so might cause serious harm.
• Do not operate a blind which in any way is damaged
• Charging of battery operated blinds, only with suitable chargers
• only operate the blind within the prescribed environmental situation
• the motor may only be used in combination with the recommended and suitable power source, originally supplied
with the blind.
• A remote control is considered NOT to be a children's toy
• window decoration motors should be replaced when the rated cycle limitation is reached
Never drop the
Never drill into
motor!
the motor!
Page 1 of 30
Do not immerse
Avoid
into liquid!
collisions!
version: 1.2

Advertisement

loading
Need help?

Need help?

Do you have a question about the PowerView M25T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HunterDouglas PowerView M25T

Summary of Contents for HunterDouglas PowerView M25T

  • Page 1 MANUAL Safety instructions The motor may only be operated after reading these safety instructions, failing to do so might cause serious harm. • Do not operate a blind which in any way is damaged • Charging of battery operated blinds, only with suitable chargers •...

  • Page 2: Delivery Condition

    MANUAL PowerView® Twist® Roller Blind 18VDC The PowerView® M25T tubular motor is suited to be used with Twist® Roller Blinds from HunterDouglas. Twist® Roller Blind 1. Delivery condition As standard, no remote control or hub is connected to the motor. No limits are set. Motor is default set to Roller blind motor type.
  • Page 3 MANUAL 1.1.1 Power up the motor by connecting the power cable to the battery wand or power supply. 1.1.2 Immediately Check the motor button LED sequence after start up. 1.1.3 LED sequence of motor set to LED sequence of motor set to Roller blind Twist®...
  • Page 4 MANUAL Note  This procedure can be skipped for a fresh out of the box motor. The motor will jog 2x when receiving any PowerView® command (e.g. Pressing the manual control button on the motor), to confirm no limits are set. 1.2.1 Remove power from the motor by disconnecting the power cable from the battery wand or power supply...

  • Page 5: Network Reset

    MANUAL 1.2.4 Press and hold the manual control button until the motor jogs 1x. The motor LED flashes red-orange after the motor jogs 1.2.5 Release the manual control button The end limits have been cleared. 1.3. Network reset This procedure will erase all network data stored in the motor, including Network ID and Group assignments. It will not clear the end limits.
  • Page 6 MANUAL 1.3.2 Release the manual control button after the second jog. The Network ID and Group assignments have been cleared. 2. Pairing a remote A PowerView® remote can control up to 6 individual groups of blinds (buttons 1 to 6 at the top of the remote). The instructions below assign a blind to group 1.
  • Page 7 MANUAL Press the  button. group1 IMPORTANT  Watch out to perform steps 2.4 and 2.5 within 3 seconds! Press and hold the manual control button Press the  open button. The blind will jog 1x. Page 7 of 30 version: 1.2...
  • Page 8 MANUAL Release the manual control button Press and hold the  button for 6 seconds. stop Keep pressing until the remote lights stop blinking. The remote will exit programming mode automatically after 20 seconds. 3. Checking motor direction IMPORTANT  Reversing motor direction is only possible with a fresh out of the box motor (no limits set) or when the end limits are reset.
  • Page 9 MANUAL 3.1.1 Press and hold the manual control button 3.1.2 Press the  button. open The blind will jog 1x. Make sure  group1 on the remote is selected. 3.1.3 Release the manual control button The motor LED turns red to acknowledge the motor is in program mode.
  • Page 10 MANUAL 3.2.1 Press the  button to check motor arrow down direction. 3.2.2.A If the blind moves upwards, immediately 3.2.2.B If the blind moves downwards, Press the  Press the  stop button. stop button and continue with step 4.1.4 Motor direction NOT OK! Motor direction OK! 3.2.3...
  • Page 11 MANUAL 4. Setting end limits It doesn’t matter if you start with setting the open or the close limit first. In this description we start with the open (top) limit. Note  It is important to have the fabric of the blind tight around the tube. 4.1.
  • Page 12 MANUAL 4.1.3 Release the manual control button The motor LED turns red to acknowledge the motor is in program mode. 4.1.4 Use the  ,  and  buttons to open stop close move the blind to the desired top position. Use the ...
  • Page 13 MANUAL IMPORTANT  Watch out to perform steps 4.1.6 and 4.1.7 within 3 seconds! 4.1.6 Press and hold the manual control button 4.1.7 Press the  button. open The blind will jog 1x to acknowledge the limit is set. 4.1.8 Release the manual control button The motor LED turns off.
  • Page 14 MANUAL 4.1.9 Press and hold the  button for 6 seconds. stop Keep pressing until the remote lights stop blinking. The remote will exit programming mode automatically after 20 seconds. 4.1.10 The top limit is set! Note  To re-position the top limit of the blind, repeat step 4.1 Open limit (top) Page 14 of 30 version: 1.2...
  • Page 15 MANUAL 4.2. Close limit (bottom) 4.2.1 Press and hold the manual control button 4.2.2 Press the  close button. The blind will jog 1x. Make sure  group1 on the remote is selected. 4.2.3 Release the manual control button The motor LED turns red to acknowledge the motor is in program mode.
  • Page 16 MANUAL 4.2.4 Use the  ,  and  buttons to open stop close move the blind to the desired bottom position. Use the  and  buttons to arrow up arrow down fine tune the desired position. 4.2.5 Press and hold the  button for 6 seconds.
  • Page 17 MANUAL 4.2.7 Press the  button. close The blind will move to the top limit to acknowledge the bottom limit is set. 4.2.8 Release the manual control button The motor LED turns off. 4.2.9 Press and hold the  button for 6 seconds. stop Keep pressing until the remote lights stop blinking.
  • Page 18 MANUAL 4.2.10 The bottom limit is set! Note  To re-position the bottom limit of the blind, repeat step 4.2. Close limit (bottom) 5. fabric open position When the end limits of a Twist® Roller Blind have been programmed correctly, setting the fabric open position allows the Twist®...
  • Page 19 MANUAL 5.1. Set fabric open position 5.1.1 Locate the on your blind. manual control button 5.1.2 Press the  group1 button. 5.1.3 Press the  button to move the blind to the close bottom position. Page 19 of 30 version: 1.2...
  • Page 20 MANUAL 5.1.4 Determine the fabric open position using the  ,  and  buttons. arrow up arrow down stop 5.1.5 Press and hold the  button for 6 seconds. stop Keep pressing until the remote lights start blinking. DO NOT select a group on the remote! IMPORTANT ...
  • Page 21 MANUAL 5.1.7 Press the  button. arrow up The blind will jog 1x to acknowledge the fabric open position is set. 5.1.8 Release the manual control button 5.1.9 Press and hold the  button for 6 seconds. stop Keep pressing until the remote lights stop blinking. The remote will exit programming mode automatically after 20 seconds.
  • Page 22 MANUAL 5.1.10 The fabric open position is set! 5.2 Clear fabric open position When the fabric open position of a Twist® Roller Blind is not programmed correctly or a new position needs to be set, the current fabric open postion can be easily removed and allows you to program a new fabric open position. 5.2.1 Press the ...
  • Page 23 MANUAL 5.2.2 Use the  ,  ,  ,  open close stop arrow up buttons to move the blind to the arrow down  fabric open position. 5.2.3 Find the manual control button on your blind. 5.2.4 Press and hold  for 6 seconds.
  • Page 24 MANUAL 5.2.5 Press and hold the manual control button 5.2.6 Press the  button. arrow down The blind will jog 1x to acknowledge the fabric open position is removed. 5.2.7 Release the manual control button 5.2.8 Press and hold  stop for 6 seconds.

  • Page 25: Delivery Conditions

    MANUAL 5.2.9 The fabric open position is cleared! Note  To set a new fabric open position, repeat step 5.1. Setting fabric open position. 6. Special motor functions This chapter describes how to activate special functions with a standard PowerView® remote control: When activating a PowerView®...
  • Page 26 MANUAL 6.2. Enable Twist® Roller Blind type & Disable slow scene speed 6.2.1 Select the right group on the remote. In our example, we select  on the group1 remote. IMPORTANT  In the next steps, all buttons have to be pressed with a second interval! 6.2.2 1.
  • Page 27 MANUAL 6.3. Enable Twist® Roller Blind type 6.3.1 Select the right group on the remote. In our example, we select  on the group1 remote. IMPORTANT  In the next steps, all buttons have to be pressed with a second interval! 6.3.2 1.
  • Page 28 MANUAL 7. Motor control button LED The motor control button LED gives an indication of the motor status. The LED can flash RED, ORANGE or GREEN. Below is the overview of all possible combinations. Sequence Explanation After power up Restart / Start up Blind type: Roller blind Blind type:...

  • Page 29: Important Notice

    MANUAL Network reset on manual control button release, chapter 1.3. Blind type: Roller blind Network reset on manual control button release, chapter 1.3. Blind type: Twist® Roller Blind Battery operation Low battery indication (< 11.0V). The blind will run in slow mode and can only be send upwards.
  • Page 30 MANUAL specifications applicable at the time of sale, in accordance with its standard warranty terms. Testing and other quality control techniques are used to the extent Hunter Douglas deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed.