Gage Bilt GB756 Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Tools
  5. GB756
  6. Manual

Gage Bilt GB756 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S/N: 1226 AND ABOVE
GB756
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB756 and is the answer not in the manual?

Questions and answers

Related Manuals for Gage Bilt GB756

Summary of Contents for Gage Bilt GB756

  • Page 1 S/N: 1226 AND ABOVE GB756 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    Dexron III, or equivalent. Setting stroke - .960" (24.4mm) Rated pull load - 10,000 lbs. (44.5kN) Noise level - 81.5 dB (A) Vibration - Tested– No hazards found. S/N: 1226 AND ABOVE REV. 3/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    81.5 dB(A). Therefore, daily basis for damage or wear. Any repair should it is required where prolonged use, hearing be done by qualified personnel trained on Gage Bilt protection be used. procedures. WARNING...

  • Page 4: How To Use The Gb756

    NOSE ASSEMBLY CYLINDER HEAD DEFLECTOR RIVET WORK TRIGGER SHIPPING PLUG Image may not reflect actual tool QUICK DISCONNECT FITTING S/N: 1226 AND ABOVE REV. 3/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: Description, Operation And Maintenance

    It has a .960" (24.4mm) rivet setting stroke and a rated pull load of 10,000 lbs (44.5kN). The GB756 riveter operates with 90 to 100 psi (6.2-6.9 bar) of air. At 90 psi. (6.2 bar) air pressure, the GB756 does not exceed 81.5 db (A) and consumes 6.0 cfm at 20 cycles per minute.

  • Page 6: Filling And Bleeding

    (A-1115) from holes marked #1 and #2 and push piston ass’y (756211) to the rear (Dim. B). Replace rear button head screw (402482) and stat-o-seal (A-1115) in rear hold marked #2 and repeat steps 9-20. S/N: 1226 AND ABOVE REV. 3/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 7: Stroke Chart

    19.05mm 3.73mm 22.78mm .375" .147" .522" 756155 .585 9.53mm 3.73mm 13.26mm Bleeder screw 402482 and seal A-1155 Bleeder screw 402482 and seal A-1155 Figure “B” S/N: 1226 AND ABOVE REV. 3/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Troubleshooting And Overhaul

    Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.

  • Page 9: Disassembly And Parts Lists

    (756144). With piston rod ass’y (756134) in the down position, fill oil passages on top of handle (756229) with automatic transmission fluid. S/N: 1226 AND ABOVE REV. 3/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 10 A-1087 - RETAINING RING 756243 - SPACER A-1095 - POLYSEAL S837 - O'RING 403176 - PARBAK 756218 - PACKING PLUG 400779 - O'RING Figure “C” S/N: 1226 AND ABOVE REV. 3/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 11: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations S/N: 1226 AND ABOVE REV. 3/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Nose Assembly/Stroke Limiter Attachment

    Nose assemblies are attached using a 1-1/4 inch socket on the rear of the piston ass’y. Socket (A-1307) may be ordered separately from Gage Bilt. GB756TK tool repair kit may also be ordered separately which in- cludes socket (A-1307) and other tools needed for complete tool overhaul.

  • Page 13: Nose Assembly Selection Chart

    A SP ®, B OM ®, LGP ®, C6L®, GP ®, A ND M A GNA -GRIP ® A RE REGISTERED TRA DEM A RKS OF A LCOA INC. A VB OLT®, A VDELOK®, A ND M A XLOK® A RE REGISTERED TRA DEM A RKS OF A VDEL UK LIM ITED. GAGE BILT CERTIFIES THE GB756 WILL INSTALL THE ABOVE FASTENERS *ALL OFFSET 204 SERIES NOSES REQUIRE 353204 ADAPTER WITH 756152 STROKE LIMITER..

  • Page 14: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB756 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.

Table of Contents